PIETRO FIORENTINI SSM-ICON User manual

SSM-ICON
Static smart meter
EN
USE, MAINTENANCEUSE, MAINTENANCE
AND WARNINGAND WARNING
MANUALMANUAL
Revision B – Edition 02/2022

2
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B
Use, maintenance and warning manual

3
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B EN
Use, maintenance and warning manual
1 - INTRODUCTION
FOREWORD
All rights reserved. No part of this publication may be reproduced, distributed, translated into other languages or trans-
mitted by any electronic or mechanical media, including photocopies, recording or any other storage and retrieval system,
for any other purposes that are not exclusively the personal use of the buyer, without the express written permission of
the Manufacturer.
The manufacturer is in no way responsible for the consequences of operations carried out in a manner not in accordance
with the manual.
GENERAL CONSIDERATIONS
All the operating, maintenance instructions and recommendations described in this manual must be adhered to in order to:
• obtain the best possible performance from the equipment;
• keep the equipment in efcient conditions.
Training the personnel in charge is essential in order to:
• use and service the equipment properly;
• correctly apply the safety alerts and procedures recommended.
Revision: B
COPYRIGHT 2022
© PIETRO FIORENTINI S.P.A.
NOTICE!
The images shown in this document indicate the type of product and may differ in detail.

4
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B

5
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B EN
1.1 - REVISION HISTORY
Revision
index Date Revision contents
A02/2022 First issue
B02/2022
Changed name SSM-iCON > SSM-ICON
Chap. 1: added note in foreword
Par. 4.1.4: edited paragraph (Acquisition)
Par. 4.3: changes in tab. 4.20 (Technical data)
Par. 2.8.1.1: changes in tab. 2.9 (Type of gauge)
Par. 2.8.1.2: changes in tab. 2.10 (Type of remote communication)
Par. 3.6: edited paragraph (Safety and anti-fraud)
Tab. 1.1.

6
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B
TABLE OF CONTENTS
1 - INTRODUCTION .................................................................................................................. 3
1.1 - REVISION HISTORY.................................................................................................................................. 5
2 - GENERAL INFORMATION ................................................................................................ 11
2.1 - MANUFACTURER IDENTIFICATION........................................................................................................ 11
2.2 - IDENTIFICATION OF THE PRODUCT ...................................................................................................... 11
2.3 - REGULATORY FRAMEWORK................................................................................................................. 12
2.4 - WARRANTY............................................................................................................................................ 12
2.4.1 - REFERENCE OPERATING CONDITIONS ..............................................................................................13
2.5 - ADDRESSEES, SUPPLY AND STORAGE OF THE MANUAL................................................................... 14
2.6 - LANGUAGE ............................................................................................................................................ 14
2.7 - SYMBOLS USED IN THE MANUAL......................................................................................................... 15
2.8 - NAMEPLATES APPLIED ......................................................................................................................... 16
2.8.1 - IDENTIFIER OF THE LOGIC DEVICE .....................................................................................................17
2.8.1.1 - TYPE OF GAUGE .........................................................................................................................17
2.8.1.2 - REMOTE COMMUNICATION TYPE ..............................................................................................17
2.8.2 - DESCRIPTION OF THE NAMEPLATES..................................................................................................18
2.9 - GLOSSARY OF MEASUREMENT UNITS................................................................................................. 19
2.10 -QUALIFIED PROFESSIONAL FIGURES................................................................................................... 20
3 - SAFETY .............................................................................................................................. 21
3.1 - GENERAL SAFETY WARNINGS.............................................................................................................. 21
3.2 - ATEX DIRECTIVE SAFETY INSTRUCTIONS ............................................................................................ 22
3.2.1 - ELECTROSTATIC DISCHARGES...........................................................................................................22
3.2.2 - CONNECTING TO OTHER DEVICES.....................................................................................................22
3.2.3 - POWER SUPPLY DEVICES ...................................................................................................................22
3.2.4 - SAFETY INSTRUCTIONS FOR INSTALLATION IN HAZARDOUS AREA.................................................23
3.3 - PERSONAL PROTECTIVE EQUIPMENT.................................................................................................. 24
3.4 - OBLIGATIONS AND PROHIBITIONS....................................................................................................... 25
3.5 - RESIDUAL RISKS ................................................................................................................................... 26
3.5.1 - RISK OF ELECTROSTATIC DISCHARGE...............................................................................................26
3.6 - SAFETY AND FRAUD PREVENTION....................................................................................................... 27
3.7 - SAFETY PICTOGRAMS .......................................................................................................................... 28
3.8 - RISK LEVEL ............................................................................................................................................ 28

7
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B EN
4 - DESCRIPTION AND OPERATION .................................................................................... 29
4.1 - GENERAL DESCRIPTION ....................................................................................................................... 29
4.1.1 - POWER SUPPLY DEVICES ...................................................................................................................30
4.1.1.1 - CONNECTION OF THE POWER SUPPLY DEVICES .....................................................................30
4.1.1.2 - POWER SUPPLY STATUS ............................................................................................................30
4.1.2 - SHUT-OFF VALVE (OPTIONAL)..............................................................................................................31
4.1.3 - ACQUISITION OF THE MEASURE.........................................................................................................32
4.1.4 - EVENTS AND DIAGNOSTICS................................................................................................................32
4.1.5 - ACTIVATION AND CONFIGURATION.....................................................................................................32
4.1.6 - COMMUNICATION INTERFACES ..........................................................................................................32
4.1.7 - USER INTERFACE.................................................................................................................................32
4.2 - INTENDED USE ...................................................................................................................................... 33
4.2.1 - ENVISAGED USE ..................................................................................................................................33
4.2.2 - REASONABLY FORESEEABLE MISUSE ...............................................................................................33
4.3 - TECHNICAL DATA .................................................................................................................................. 34
5 - USER INTERFACE............................................................................................................. 35
5.1 - GENERAL DESCRIPTION ....................................................................................................................... 35
5.2 - LCD DISPLAY DESCRIPTION ................................................................................................................. 36
5.3 - NAVIGATION PROCEDURE .................................................................................................................... 38
5.3.1 - DEFAULT CHAPTER (CURRENT RATE PERIOD)...................................................................................39
5.3.2 - CHAPTER SELECTION .........................................................................................................................39
5.3.3 - CHAPTER 1 (PREVIOUS BILLING PERIOD)...........................................................................................40
5.3.4 - CHAPTER 2 (MAIN PARAMETERS).......................................................................................................40
5.3.4.1 - SUB-MENU OF THE FIRMWARE DEVICE AND THE OPERATING STATUS ..................................41
5.3.5 - CHAPTER 3 (SERVICE) .........................................................................................................................42
5.3.6 - CHAPTER 4 (COMMUNICATION)..........................................................................................................43
5.4 - ALARMS ................................................................................................................................................. 43
5.5 - OPTIONAL SHUT-OFF VALVE OPENING................................................................................................. 44

8
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B
6 - TRANSPORT AND HANDLING......................................................................................... 45
6.1 - SPECIFIC WARNINGS FOR TRANSPORT AND HANDLING ................................................................... 45
6.1.1 - PACKAGING AND FASTENERS USED FOR TRANSPORT ....................................................................45
6.2 - PACKAGING CONTENT.......................................................................................................................... 46
6.3 - PHYSICAL CHARACTERISTICS OF THE EQUIPMENT ........................................................................... 47
6.4 - EQUIPMENT ANCHORING AND LIFTING METHOD................................................................................ 48
6.4.1 - FORKLIFT HANDLING METHOD...........................................................................................................49
6.5 - PACKAGING REMOVAL.......................................................................................................................... 51
6.5.1 - PACKAGING DISPOSAL .......................................................................................................................51
6.6 - STORAGE AND ENVIRONMENTAL CONDITIONS .................................................................................. 52
6.6.1 - STORAGE OF THE SPARE BATTERIES ................................................................................................52
7 - INSTALLATION .................................................................................................................. 53
7.1 - GENERAL WARNINGS ........................................................................................................................... 53
7.2 - INSTALLATION PRE-REQUISITES........................................................................................................... 53
7.2.1 - ALLOWED ENVIRONMENTAL CONDITIONS.........................................................................................53
7.3 - CHECKS BEFORE INSTALLATION.......................................................................................................... 54
7.4 - SPECIFIC SAFETY INSTRUCTIONS FOR THE INSTALLATION STEP...................................................... 55
7.5 - INSTALLATION PROCEDURE ................................................................................................................. 56
7.6 - EQUIPMENT ADJUSTMENTS................................................................................................................. 57
8 - CONFIGURATION.............................................................................................................. 59
8.1 - SAFETY REQUIREMENTS FOR CONFIGURATION ................................................................................. 59
8.2 - EQUIPMENT CONFIGURATION .............................................................................................................. 59
8.2.1 - USING THE OPTICAL PROBE...............................................................................................................59
8.3 - VERIFY CORRECT CONFIGURATION..................................................................................................... 59
8.4 - CONNECTING TO OTHER DEVICES ...................................................................................................... 59
9 - MAINTENANCE AND FUNCTIONAL CHECKS................................................................ 61
9.1 - GENERAL WARNINGS ........................................................................................................................... 61
9.2 - SPECIAL MAINTENANCE ....................................................................................................................... 62
9.2.1 - REPLACING THE COMMUNICATION BATTERY PACK .........................................................................62
9.2.2 - SIM REPLACEMENT (ONLY FOR SSM-ICON-GPRS AND SSM-ICON-NB) VERSIONS) ........................65

9
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B EN
10 - UNINSTALLATION AND DISPOSAL ................................................................................. 67
10.1 -GENERAL SAFETY WARNINGS.............................................................................................................. 67
10.2 -QUALIFICATION OF THE OPERATORS IN CHARGE............................................................................... 67
10.3 -UNINSTALLATION................................................................................................................................... 67
10.4 -INFORMATION REQUIRED IN CASE OF NEW INSTALLATION................................................................ 68
10.5 -STORAGE OF THE BATTERIES .............................................................................................................. 68
10.6 -INFORMATION REQUIRED IN CASE OF RE-INSTALLATION................................................................... 68
10.7 -DISPOSAL INFORMATION...................................................................................................................... 69
10.7.1 - DISPOSING OF THE BATTERIES .........................................................................................................70
10.7.1.1 - BATTERY PACKAGING.................................................................................................................70
11 - RECOMMENDED SPARE PARTS..................................................................................... 71
11.1 -GENERAL WARNINGS ........................................................................................................................... 71
11.2 -HOW TO REQUEST SPARE PARTS........................................................................................................ 71
11.3 -SPARE PARTS LIST ................................................................................................................................ 72
11.4 -PUTTING BACK BATTERIES................................................................................................................... 72

10
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |INTRODUCTION |REV. B
PAGE INTENTIONALLY LEFT BLANK

11
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B EN
2 - GENERAL INFORMATION
2.1 - MANUFACTURER IDENTIFICATION
Manufacturer PIETRO FIORENTINI S.P.A.
Address
Via Enrico Fermi, 8/10
36057 Arcugnano (VI) - ITALY
Tel. [phone] Fax [phone]
www.orentini.com sales@orentini.com
Tab. 2.2.
NOTICE!
For any problem encountered on the equipment, contact the distributor of the reference gas mains.
2.2 - IDENTIFICATION OF THE PRODUCT
Equipment STATIC SMART METER
Series SSM-ICON
Available models
• SSM-ICON-U6-GPRS
• SSM-ICON-U6-169
• SSM-ICON-U6-NB
NOTICE!
The same models are also available in the “EL” (“Extended Life”) version.
Tab. 2.3.

12
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B
2.3 - REGULATORY FRAMEWORK
PIETRO FIORENTINI S.P.A. with registered ofce in Arcugnano (Italy) - Via E. Fermi, 8/10, declares that the equipment of
the SSM-ICON series described in this manual is designed, manufactured, tested and checked in compliance with:
• the requirements of the Directives:
• 2014/32/EU “MID”;
• 2014/34/EU “ATEX”;
• 2014/53/EU “RED”;
• 2011/65/UE “RoHS 2”;
• 2012/19/EU “WEEE”;
• resolution 631/2013/R/gas of the Regulatory Authority for Energy, Networks and Environment (ARERA) and ratied in
the UNI/TS 11291 package of standards.
NOTICE!
For specic type approvals, see the appropriate section on the Manufacturer’s website: https://www.or-
entini.com
NOTICE!
The declaration of conformity in its original version is delivered together with the equipment.
2.4 - WARRANTY
PIETRO FIORENTINI S.P.A. guarantees that the equipment was manufactured using the best materials, with high quality
workmanship, and complies with the quality requirements, specications and performance set out in the order.
The warranty shall be considered null and void and PIETRO FIORENTINI S.P.A. shall not be liable for any damage and/or
malfunctions:
• due to any acts or omissions of the purchaser or end-user, or any of their carriers, employees, agents, or any third
party or entity;
• in the event that the purchaser, or a third party, makes changes to the equipment supplied by PIETRO FIORENTINI S.P.A.
without the prior written approval of the latter;
• in the event of failure by the purchaser to comply with the instructions contained in this manual, as provided by
PIETRO FIORENTINI S.P.A.
NOTICE!
The warranty conditions are specied in the commercial contract.

13
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B EN
2.4.1 - REFERENCE OPERATING CONDITIONS
The reference operating conditions to calculate the life span of the batteries are described in the UNI/TS 11291-11-1 and
11291-12-1 standards. An extract of these standards is found in Tab. 2.4:
Operative
condition Reference indications
User interface 10 minutes per month (local interface).
20 minutes per month (Display).
Shut-off
valve
(optional)
2 handling cycles (opening/closing) every year.
Upgrade
rmware code Twice in 15 years.
Communication
GPRS Version:
• 1 communication per day (recording = 30 sec., communication = 20 sec.).
Version NBIoT:
• 1 recording per year;
• 1 communication per day.
Version RF169:
• 4 transmissions per day (Tx Totaliser value);
• 1 communication per day (Tx/Rx).
Tab. 2.4.
In addition to that dened by the UNI/TS 11291-11-1 and 11291-12-1 standards, the room temperature effects the life
span of the batteries. The operating prole used to calculate the battery life expectancy is indicated in Tab. 2.5:
Reference indications
Ambient temperature
0.25% of the time at -25 °C
0.5% of the time at -20 °C
2.6% of the time at -10 °C
41.0% of the time at +5 °C
43.0% of the time at +20 °C
11.8% of the time at +35 °C
0.5% of the time at +50 °C
0.25% of the time at +60 °C
0.1% of the time at +70 °C
Tab. 2.5.

14
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B
2.5 - ADDRESSEES, SUPPLY AND STORAGE OF THE MANUAL
The manual is intended for the qualied technician responsible for operating and managing the equipment throughout its
service life.
It contains the necessary information for the correct use of the equipment in order to maintain its functional and qualitative
characteristics over time. All information and warnings for correct use in full safety are also provided.
The manual, as well as the declaration of conformity and/or test certicate, is an integral part of the equipment and must
always accompany it whenever it is moved or resold. It is the responsibility of the qualied professionals (see paragraph
2.10) to use and manage the equipment.
WARNING!
Removing, rewriting or modifying the pages of the manual and their contents is not allowed.
PIETRO FIORENTINI S.p.A. shall not be held liable for any damage to people, animals and property caused
by failure to adhere to the warnings and operating procedures described in this manual.
2.6 - LANGUAGE
The original manual has been drawn up in Italian.
Any translations into additional languages must be made from the original manual.
HAZARD!
The translations into other languages cannot be fully veried. If any inconsistency is found, please refer to
the text of the original manual.
If inconsistencies are found or the text does not make sense:
• stop any actions;
• immediately contact PIETRO FIORENTINI S.p.A. at the addresses specied in paragraph 2.1 (“Identi-
cation of the manufacturer”).
WARNING!
PIETRO FIORENTINI S.p.A. shall be held liable for the information provided in the original manual only.

15
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B EN
2.7 - SYMBOLS USED IN THE MANUAL
Symbol Denition
Symbol used to identify important warnings for the safety of the operator and/or equipment.
Symbol used to identify information of particular importance in the manual.
The information may also concern the safety of the personnel involved in using the equipment.
Obligation to consult the instruction manual/booklet.
Refers to a requirement for personnel to refer to (and understand) the operating and warning
instructions of the machine before working with or on it.
Tab. 2.6.
HAZARD!
Alerts to a hazard with a high level of risk, an imminent hazardous situation which, if not prevented, will
result in death or severe damage.
WARNING!
Alerts to a hazard with a medium level of risk, a potentially hazardous situation which, if not prevented,
may result in death or severe damage.
ATTENTION!
Alerts to a hazard with a low level of risk, a potentially hazardous situation which, if not prevented, could
result in minor or moderate damage.
NOTICE!
Alerts to specic warnings, directions or notes of particular concern, that are not related to physical injury,
as well as practices for which physical injury is not likely to occur.

16
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B
2.8 - NAMEPLATES APPLIED
The equipment and its accessories are provided with nameplates (from Id.1 to Id.3).
The plates specify identication details of the equipment and its accessories to be mentioned in case of need to
PIETRO FIORENTINI S.p.A.
List of the nameplates applied:
Id. Type of plate Image
1Mod. SSM-ICON-U6-GPRS
0407
I-2142-MI002-TG037
MYY
EN 14236:2018 Classe 1,5 "H3" "T"
Qmax= 6 m3/h Qt= 0,6 m3/h Qmin= 0,04 m3/h
tm-25 °C... +55 °C tg-25 °C... +55 °C tb15 °C
tsp 15 °C pmax 0,5 bar M2/E2 Gruppi H, L, E
2Mod. SSM-ICON-U6-169
0407
I-2142-MI002-TG037
MYY
EN 14236:2018 Classe 1,5 "H3" "T"
Qmax= 6 m3/h Qt= 0,6 m3/h Qmin= 0,04 m3/h
tm-25 °C... +55 °C tg-25 °C... +55 °C tb15 °C
tsp 15 °C pmax 0,5 bar M2/E2 Gruppi H, L, E
3Mod. SSM-ICON-U6-NB
0407
I-2142-MI002-TG037
MYY
EN 14236:2018 Classe 1,5 "H3" "T"
Qmax= 6 m3/h Qt= 0,6 m3/h Qmin= 0,04 m3/h
tm-25 °C... +55 °C tg-25 °C... +55 °C tb15 °C
tsp 15 °C pmax 0,5 bar M2/E2 Gruppi H, L, E
Tab. 2.7.
WARNING!
Removing nameplates and/or replacing them with other plates is strictly prohibited.
Should the plates be unintentionally damaged or removed, the customer must notify
PIETRO FIORENTINI S.p.A.

17
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B EN
2.8.1 - IDENTIFIER OF THE LOGIC DEVICE
Term Description
Format FIO-N-03-WV-YY-XXXXXX
FIO Fixed eld indicating the manufacturer (PIETRO FIORENTINI S.p.A.)
according to the encoding of the Flag Association
NReserved eld
03 Type of device (03=Gas Meter)
WType of gauge
VRemote communication type
YY Year of manufacture
XXXXXX Progressive number
Tab. 2.8.
2.8.1.1 - TYPE OF GAUGE
Code
“W” version Gauge value Model code
CG4 SSM-ICON-U6
Tab. 2.9.
2.8.1.2 - REMOTE COMMUNICATION TYPE
Code
“V” version Type of communication Model code
0RF 169 MHz SSM-ICON-U6-169
1GPRS SSM-ICON-U6-GPRS
4NB-IoT SSM-ICON-U6-NB
Tab. 2.10.

18
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B
2.8.2 - DESCRIPTION OF THE NAMEPLATES
The following information, described in Tab.2.11, is shown on the nameplate:
Pos. Description
1Manufacturer’s Logo.
2Static smart meter series.
3Communication battery pack identication code and device identication type.
4a Identier of the logic device (QR code).
4b Identier of the logic device.
4c Identier of the logic device (barcode).
5Casing protection rating.
6“ATEX” Directive marking.
7Reference standard for “Domestic ultrasonic gas meters”, Manufacturer's calibrations, approval levels.
8Manufacturer’s Address.
9Model code.
10 “MID” Directive marking.
11 Meter reference class.
12 Disposal guidelines (WEEE Directive 2012/19/EU).
Tab. 2.11.
1 211
9
6
4a
5 4c 4b
3
7
8
10 12
0407
I-2142-MI002-TG037
MYY
EN 14236:2018 Classe 1,5 "H3" "T"
Qmax= 6 m3/h Qt= 0,6 m3/h Qmin= 0,04 m3/h
tm-25 °C... +55 °C tg-25 °C... +55 °C tb15 °C
tsp 15 °C pmax 0,5 bar M2/E2 Gruppi H, L, E
Fig. 2.1. Description of the nameplates

19
SSM-ICON
Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B EN
2.9 - GLOSSARY OF MEASUREMENT UNITS
Type of measurement Unit of measurement Description
Consumption and
Volumetric ow rate
Sm³/h Standard cubic metres per hour
Sm³ Standard cubic metres
m³/h Cubic metres per hour
m³ Cubic metres
Pressure
bar Bar
˝wc Water column inch
Pa Pascal
Temperature °C Degree centigrade
K Kelvin
Tightening torque Nm Newton metro
Other measures
V Volt
W Watt
ΩOhm
Tab. 2.12.

20
SSM-ICON
EN Use, maintenance and warning manual
STATIC SMART METER |GENERAL INFORMATION |REV. B
2.10 - QUALIFIED PROFESSIONAL FIGURES
Qualied operators in charge of using and managing the equipment throughout its technical service life to be used as
indicated:
Professional gure Denition
Installer
Qualied operator able to:
• handle materials and equipment.
• carry out all the operations necessary to properly install the equipment;
• perform all the operations necessary to safely operate the equipment and system;
• be able to perform all the operations necessary to uninstall and subsequently dispose of
the equipment in compliance with the regulations in force in the country of installation.
Specialised
technician/
Maintenance
technician
Trained and authorised technician on the management and use of the equipment, who
must:
• be able to perform all operations required for the proper functioning of the equipment
and the system, and for their safety and that of any third parties present;
• perform maintenance on all parts of the equipment subject to maintenance (board and
batteries);
• access all device parts for visual inspection, checking equipment status, making adjust-
ments and calibrations;
• have proven experience in properly using the equipment similar to that described in this
manual, and be trained, informed and instructed in this regard.
Tab. 2.13.