Pinnacle Ikonic dss003 User manual

On the back of the lock you will see screw buttons which relate to the push buttons on the front of the lock.

To set the numbers for your code, depress and turn the screw button relating to the desired digit 180 degrees so that the

dot is facing inwards (towards the F). If you wish to take a number out of the code, turn the screw button so that the dot

is facing outwards (towards G).

IMPORTANT NOTE: Be sure to check the code on the lock works before tting/re-tting the lock and closing the door.

When the lock is coded and you would like to change the code, be sure to turn all screw buttons from the current code in

a clockwise direction 180 degrees (all dots facing outwards) to cancel the original code then set your new one.

Each and every time you wish to unlock your door you must start by pushing the ‘C’ button.

The snib on the internal block can be used to keep the latch open. Simply turn the lever handle to withdraw the

latch and push the snib to the opposite side.

See instructions on the snib that performs this function in the next section. Also check that the latch moves freely by pressing the end and by turning with the spindle.

ALL NUMBERS OFF ALL NUMBERS ON

Applying the template:

1) Tape the template to the door. Make sure that you fold it along the appropriate line.

The back set on the included latch is 60mm.

2) Mark and drill the two 10mm holes and one 13mm hole.

3) Mark a central point on the “center line of latch” on the door edge.

4) Drill a 25mm hole x 85mm deep.

5) Insert the latch into the hole and draw around the face plate.

6) Remove the latch and cut a 3mm rebate so that the face plate will t ush with the door.

7) Secure the latch with the wood screws.

Please fasten all screws by hand. Do not use an

electric screwdriver or drill as over tightening is

not recommended.

You will need untighten the screw in the large hole on the

back of your digital lock to change the vertical handle to a

horizontal left or right hand opening.

Please Note:

13mm

&10mm

drill bits

Fixing the lock

1) Cut the xing bolt length to suit the thickness of your door.

2) Place the neoprene seals between the front and back plate and install onto door.

3) Tighten the upper and lower xings although be sure not to over tighten the xing bolts as this may

cause distortion and lead to poor operation.

Please note: Do not close the door until you are sure that the code works.

Fitting the spring loaded spindle

1) The split is loaded with a spring which ensures the split line is in line with the center line of the latch.

2) The spring can be used for doors with a thickness of 35 - 60mm.

3) The spring installed must be on the end that goes into the front plate.

Split line of latch

Front plate

Fitting the striker plate:

1) Position the striker plate on the door so that it lines up with the at base of the latch bolt (not the plunger).

2) Mark the inner and outer edges of the striker plate with a pencil/marker then remove and cut a 1mm rebate so that the striker plate

ts ush with the surface of the door frame.

3) Drill or cut the recess for the latch bolt.

4) Fix the striker plate with one screw rst. Test the lock to see if it works and is latching and locking correctly. If not proceed with any

necessary adjustments before securing completely.

Handy Hint

• If your door frame interferes with the lever it can be reversed by simply loosening the screw from the large hole in the back with a

screwdriver which will then loosen the handle and allow you to rotate it in the position that best suits your door. Please refer to diagram.

Please note: Every time you wish to unlock your door you must start by pushing “C”.

Warranty conditions

Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under this warranty, take the product (with proof of purchase) to any Bunnings store (for AUS customers seewww.bunnings.

com.auand for NZ customers see www.bunnings.co.nz for store locations). Pinnacle Hardware bears reasonable, direct expenses of claiming under the warranty. You may submit details and proof of purchase to our support centre for

consideration. The warranty covers manufacturer defects in materials, workmanship and nish under normal use. This warranty is provided in addition to other rights and remedies you may have under law: Our goods come with guarantees that

cannot be excluded under the Australian consumer law or Consumer Guarantees Act 1993 (NZ). You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also

entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty excludes damage resulting from product misuse or product neglect, any modications,

additions or alterations to the product including the addition of extra shelves. Additions or modications can compromise the structure and safety of the product. The warranty covers domestic use only and does not apply to commercial

applications. This warranty is given by Pinnacle Hardware, ABN 87 614 496 196, 28 Hudson Court, Keysborough Vic 3173, 1800 349 776, Email:[email protected]. Products sold in New Zealand are imported by Bunnings New Zealand.