Pioneer AVIC-F70BT User manual

Black plate (1,1)
Installation Manual
NAVIGATION AV PLAYER
AVIC-F70BT
AVIC-F970BT
English
<CRB4539-A>1

Black plate (2,1)
Precautions
Your new product and this manual 3
Important safeguards 3
Connection
Precautions before connecting the
system 5
Before installing this product 5
To prevent damage 6
–Notice for the blue/white lead 6
Parts supplied 7
Connecting the power cord (1) 8
Connecting the power cord (2) 10
Connecting the system 12
Connecting to separately sold power
amp 13
Connecting an iPhone, iPod, Android device
or a MirrorLink™device 14
Connecting an iPhone with Lightning
connector 15
–Connecting via the USB port 15
Connecting an iPhone with 30-pin
connector 15
–Connecting via the AUX input 15
–Connecting via the RGB input 16
Connecting the Android or MirrorLink™
device 16
Connecting a rear view camera 17
Connecting the external video
component 18
–Using AV input 18
–Using an AUX input 19
Connecting the rear display 20
–When using a rear display connected to
rear video output 20
Installation
Precautions before installation 21
To avoid electromagnetic interference 21
Before installing 21
–For AVIC-F70BT users 22
Installing this product 22
–Installation notes 22
–Parts supplied 23
–Installation using the screw holes on
the side of this product 23
Installing the GPS aerial 24
–Installation notes 24
–Parts supplied 24
–When installing the aerial inside the
vehicle (on the dashboard or rear
shelf) 25
Installing the microphone 26
–Parts supplied 26
–Mounting on the sun visor 26
–Installation on the steering column 27
–Adjusting the microphone angle 27
After installation
After installing this product 28
<CRB4539-A>2
Contents
Engb
2

Black plate (3,1)
Your new product and this
manual
!The navigation features of this product
(and the rear view camera option if pur-
chased) are intended solely to aid you in
the operation of your vehicle. It is not a sub-
stitute for your attentiveness, judgement
and care when driving.
!Never use this product to route to hospi-
tals, police stations, or similar facilities in
an emergency. Please call the appropriate
emergency number.
!Do not operate this product, any applica-
tions, or the rear view camera option (if pur-
chased) if doing so will divert your attention
in any way from the safe operation of your
vehicle. Always observe safe driving rules
and follow all existing traffic regulations. If
you experience difficulty in operating this
product or reading the display, park your
vehicle in a safe location and apply the
handbrake before making the necessary
adjustments.
!This manual explains how to install this
product in your vehicle. Operation of this
product is explained in the separate man-
uals.
!Do not install this product where it may (i)
obstruct the driver’s vision, (ii) impair the
performance of any of the vehicle’s operat-
ing systems of safety features, including
airbags, hazard lamp buttons, or (iii) impair
the driver’s ability to safely operate the vehi-
cle. In some cases, it may not be possible
to install this product because of the vehi-
cle type or the shape of the vehicle interior.
!Model icons shown in this manual indicate
that the description is intended for the
models indicated by the icons.
If the following icon is shown, the descrip-
tion is applied only to the model shown.
e.g.)
F70BT
Important safeguards
WARNING
Pioneer does not recommend that you install
this product yourself. This product is de-
signed for professional installation only. We
recommend that only authorised Pioneer ser-
vice personnel, who have special training
and experience in mobile electronics, set up
and install this product. NEVER SERVICE
THIS PRODUCT YOURSELF. Installing or
servicing this product and its connecting
cables may expose you to the risk of electric
shock or other hazards, and can cause da-
mage to this product that is not covered by
warranty.
!Read this manual fully and carefully before
installing this product.
!Keep this manual handy for future refer-
ence.
!Pay close attention to all warnings in this
manual and follow the instructions care-
fully.
!This product may in certain circumstances
display inaccurate position of your vehicle,
the distance of objects shown on the
screen, and compass directions. In addi-
tion, the system has certain limitations, in-
cluding the inability to identify one-way
streets, temporary traffic restrictions and
potentially unsafe driving areas. Please ex-
ercise your own judgement in the light of
actual driving conditions.
!As with any accessory in your vehicle’s in-
terior, this product should not divert your
attention from the safe operation of your
vehicle as it may result in serious injury or
death. If you experience difficulty in operat-
ing the system or reading the display,
please make adjustments while safely
parked.
!Please remember to wear your seat belt at
all times while operating your vehicle. If
you are in an accident, your injuries can be
considerably more severe if your seat belt
is not properly fastened.
<CRB4539-A>3
Engb 3
Section
01
Precautions
Precautions

Black plate (4,1)
!Certain country and government laws may
prohibit or restrict the placement and use
of this product in your vehicle. Please com-
ply with all applicable laws and regulations
regarding the use, installation and opera-
tion of this product.
<CRB4539-A>4
Engb
4
Section
01 Precautions

Black plate (5,1)
Precautions before
connecting the system
WARNING
Do not take any steps to tamper with or dis-
able the handbrake interlock system which
is in place for your protection. Tampering
with or disabling the handbrake interlock
system could result in serious injury or
death.
CAUTION
!If you decide to perform the installation
yourself, and have special training and ex-
perience in the mobile electronics instal-
lations, please carefully follow all of the
steps in the installation manual.
!Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wir-
ing to remain exposed.
!Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger com-
partment into the engine compartment. If
the yellow lead’s insulation tears as a re-
sult of contact with metal parts, short-cir-
cuiting can occur, resulting in
considerable danger.
!It is extremely dangerous to allow cables
to become wound around the steering col-
umn or gearstick. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or hin-
der driving.
!Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle’s moving parts, espe-
cially the steering wheel, gearstick, hand-
brake, sliding seat tracks, doors, or any of
the vehicle’s controls.
!Do not route wires where they will be ex-
posed to high temperatures. If the insula-
tion heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
!Do not cut the GPS aerial cable to shorten
it or use an extension to make it longer.
Altering the aerial cable could result in a
short circuit or malfunction.
!Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse resis-
tor or filter, etc.) may fail to work properly.
!Never feed power to other electronic pro-
ducts by cutting the insulation of the
power supply lead of this product and tap-
ping into the lead. The current capacity of
the lead will be exceeded, causing over-
heating.
Before installing this product
!Use this unit with a 12-volt battery and ne-
gative earthing only. Failure to do so may
result in a fire or malfunction.
!To avoid shorts in the electrical system, be
sure to disconnect the (–) battery cable be-
fore installation.
<CRB4539-A>5
Engb 5
Section
02
Connection
Connection

Black plate (6,1)
To prevent damage
WARNING
!Use speakers over 50 W (output value)
and between 4 Wto 8 W(impedance value).
Do not use 1 Wto 3 Wspeakers for this
unit.
!The black cable is earth. When installing
this unit or power amp (sold separately),
make sure to connect the earth wire first.
Ensure that the earth wire is properly con-
nected to metal parts of the car’s body.
The earth wire of the power amp and the
one of this unit or any other device must
be connected to the car separately with
different screws. If the screw for the earth
wire loosens or falls out, it could result in
fire generation of smoke or malfunction.
Earth wire
Metal parts of car’s bod
y
Power amp
Other devices
(Another electronic
device in the car)
*1Not supplied for this unit.
!When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
!When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
!This product cannot be installed in a vehi-
cle without ACC (accessory) position on
the ignition switch.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
!To avoid short-circuiting, cover the discon-
nected lead with insulating tape. It is espe-
cially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.
!Attach the connectors of the same colour
to the corresponding coloured port, i.e.,
blue connector to the blue port, black to
black, etc.
!Refer to the owner’s manual for details on
connecting the power amp and other units,
then make connections accordingly.
!Since a unique BPTL circuit is employed,
do not directly earth the *side of the
speaker lead or connect the *side of an-
other side of the speaker lead together. Be
sure to connect the *side of the speaker
lead to the *side of the speaker lead on
this product.
Notice for the blue/white lead
!When the ignition switch is turned on (ACC
ON), a control signal is output through the
blue/white lead. Connect to an external
power amp’s system remote control term-
inal, the auto-aerial relay control terminal,
or the aerial booster power control terminal
(max. 300 mA 12 V DC). The control signal
is output through the blue/white lead, even
if the audio source is switched off.
!Be sure not to use this lead as the power
supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.
!Be sure not to use this lead as the power
supply lead for the auto-aerial or aerial
booster. Such connection could cause ex-
cessive current drain and malfunction.
<CRB4539-A>6
Engb
6
Section
02 Connection

Black plate (7,1)
Parts supplied
This product Power cord
GPS aerial Microphone
USB cable
<CRB4539-A>7
Engb 7
Section
02
Connection
Connection

Black plate (8,1)
Connecting the power cord (1)








Yellow
To terminal supplied with power regardless of
ignition switch position.
Red
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (earth)
To vehicle (metal) body.
With a two-speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.
White Grey
Front speakerFront speaker
White/black Grey/black
Left Right
Rear speaker Rear speaker
Green Violet
Green/black Violet/black
<CRB4539-A>8
Engb
8
Section
02 Connection

Black plate (9,1)
Audio source will be set to mute or attenuate, while
the following sounds will not be muted or
attenuated. For details, refer to Operation Manual.
— Voice guidance of the navigation
— Incoming ring tone and incoming voice of the
mobile phone that is connected to this product
via Bluetooth wireless technology
Note
Yellow/black (MUTE)
If you use equipment with a mute
function, connect that equipment to
the Audio Mute lead. If not, keep the
Audio Mute lead free of any
connections.
Blue/white (SYSTEM REMOTE CONTROL)
To auto-aerial relay control terminal or aerial booster
power control terminal (max. 300 mA 12 V DC).
If the vehicle has a glass aerial, connect to the aerial
booster power control terminal (max. 300 mA 12 V DC).
This product
Fuse (10 A)
14 cm
Power supply
Power cord
<CRB4539-A>9
Engb 9
Section
02
Connection
Connection

Black plate (10,1)
Connecting the power cord (2)
Pink (CAR SPEED SIGNAL INPUT)
This product is connected here to detect the distance the vehicle travels. Always connect the
vehicle’s speed detection circuit. Failure to make this connection will increase errors in the
vehicle’s location display.
LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND
MUST BE CONNECTED TO THE POWER SUPPLY
SIDE OF THE HANDBRAKE SWITCH. IMPROPER
CONNECTION OR USE OF THIS LEAD MAY
VIOLATE APPLICABLE LAW AND MAY RESULT
IN SERIOUS INJURY OR DAMAGE.
Light green (PARKING BRAKE)
Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side
of the handbrake switch.
If this connection is made incorrectly or omitted, certain functions of this product will be unusable.
Power supply side
Earth side
Handbrake switch
The position of the speed detection circuit and the position of the handbrake switch vary
depending on the vehicle model. For details, consult your authorised Pioneer dealer or an
installation professional.
Note
WARNING
CAUTION
It is strongly suggested that the speed pulse wire be connected for accuracy of navigation
and better performance.
IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING
ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE
VEHICLE´S ANTILOCK BRAKING SYSTEM, AUTOMATIC GEARBOX AND
SPEEDOMETER INDICATION.
WARNING
<CRB4539-A>10
Engb
10
Section
02 Connection

Black plate (11,1)
Violet/white (REVERSE-GEAR SIGNAL INPUT)
This is connected so that this product can detect whether
the vehicle is moving forwards or backwards. Connect the
violet/white lead to the lead whose voltage changes when
the reverse gear is engaged. Unless connected, the sensor
may not detect your vehicle travelling forward/backward
properly, and thus the position of your vehicle detected by
the sensor may be misaligned from the actual position.
When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to the rear view camera picture.
This product
Note
Power cord
Power supply
<CRB4539-A>11
Engb 11
Section
02
Connection
Connection

Black plate (12,1)
Connecting the system
This product
Wired remote input
Please refer to the instruction manual for
the Hard-wired remote control adapter
(sold separately).
3.55 m
Aerial jack
Vehicle aerial
Microphone
4 m
WARNING
· To avoid the risk of accident and the potential violation of applicable laws, this
product should never be used while the vehicle is being driven except for
navigation purposes. And, also rear displays should not be in a location where it
is a visible distraction to the driver.
· In some countries, the viewing of images on a display inside a vehicle even by
persons other than the driver may be illegal. Where such regulations apply they
must be obeyed and this product’s video source should not be used.
GPS aerial
Note
F70BT
Make sure to connect the microphone supplied
with this product when using Android Auto.
<CRB4539-A>12
Engb
12
Section
02 Connection

Black plate (13,1)
Connecting to separately sold power amp












System remote control
Power cord
Blue/white
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Front speaker Rear speaker Subwoofer
RCA cables
(sold separately)
This product
15 cm
Rear outputs
(REAR OUTPUT)
Front outputs
(FRONT OUTPUT)
To system control terminal of the power amp
(max. 300 mA 12 V DC).
White, Red (SWL, SWR)
Notes
· You can change the RCA output of the subwoofer depending on your subwoofer
system. (Refer to Operation Manual.)
· The subwoofer output of this product is monaural.
Power supply
<CRB4539-A>13
Engb 13
Section
02
Connection
Connection

Black plate (14,1)
Connecting an iPhone, iPod, Android device or a
MirrorLink™device
Find your device and the function you want to operate from the list below, and refer to the page for the connection.
iPhone 6 Plus/iPhone 6/iPhone 5s/iPhone 5c/iPhone 5/iPod touch (5th generation)/iPod nano (7th genera-
tion)
Refer to Connecting via the USB port on page 15.
iPhone 4s/iPhone 4/iPhone 3GS/iPod touch (2nd, 3rd, and 4th generation)/iPod classic 160GB/iPod classic
80GB/iPod nano (3rd, 4th, 5th, and 6th generation)
Refer to Connecting via the AUX input on page 15.
Refer to Connecting via the RGB input on page 16.
Android device
Refer to Connecting the Android or MirrorLink™device on page 16.
MirrorLink device
Refer to Connecting the Android or MirrorLink™device on page 16.
<CRB4539-A>14
Engb
14
Section
02 Connection

Black plate (15,1)
Connecting an iPhone with
Lightning connector
Notes
!For details on how to connect an external de-
vice using a separately sold cable, refer to the
manual for the cable.
!For details concerning the connection, opera-
tions and compatibility of iPhone, refer to Op-
eration Manual.
Connecting via the USB port
The USB interface cable for iPod / iPhone (CD-
IU52) (sold separately) is required for the con-
nection.
USB cable
1.5 m
USB interface cable for iPod / iPhone
(CD-IU52) (sold separately)
This product
USB port 1
iPhone with
Lightning connector
USB port 2
Connecting an iPhone with
30-pin connector
Notes
!For details on how to connect an external de-
vice using a separately sold cable, refer to the
manual for the cable.
!For details concerning the connection, opera-
tions and compatibility of iPhone, refer to Op-
eration Manual.
Connecting via the AUX input
The USB interface cable for iPod / iPhone (CD-
IU201V) (sold separately) is required for the
connection.
This product
USB interface cable for iPod / iPhone
(CD-IU201V) (sold separately)
USB cable
1.5 m iPhone with
30-pin connector
AUX input
USB port 1
USB port 2
Mini-jack extension cable
(supplied with CD-IU201V)
<CRB4539-A>15
Engb 15
Section
02
Connection
Connection

Black plate (16,1)
Connecting via the RGB input
The USB interface cable for iPod / iPhone (CD-
IU201S) (sold separately) is required for the
connection.
USB cable
1.5 m
USB interface cable for iPod / iPhone
(CD-IU201S) (sold separately)
This product
USB port 1
RGB input
iPhone with
30-pin connector
Connecting the Android or
MirrorLink™device
The USB interface cable for use with Android
or MirrorLink™devices (CD-AH200) (sold sepa-
rately) is required for the connection.
USB cable
(supplied with CD-AH200)
USB - micro USB cable
(Type USB A - micro USB B)
(supplied with CD-AH200)
This product
Android or MirrorLink device
USB port 2
Note
For details on how to connect an external device
using a separately sold cable, refer to the manual
for the cable.
<CRB4539-A>16
Engb
16
Section
02 Connection

Black plate (17,1)
Connecting a rear view camera
When this product is used with a rear view
camera, it is possible to automatically switch
from the video to rear view image when the
gearstick is moved to REVERSE (R). Camera
View mode also allows you to check what is
behind you while driving.
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
!The screen image may appear reversed.
!The rear view camera is used as an aid to
keep an eye on trailers, or backing into a tight
parking spot. Do not use this function for en-
tertainment purposes.
!Objects in rear view may appear closer or
more distant than in reality.
!Please note that the image area shown by the
rear view camera may differ slightly when full-
screen images are displayed when backing
and when checking the rear of the vehicle
while moving forward.
Rear view camera
(ND-BC6)
(sold separately)
This product
Brown (BC IN)
RCA cable
(supplied with ND-BC6)
Violet/white
(REVERSE-GEAR SIGNAL
INPUT)
To video output
Power cord
Power supply
For more details about the wiring, refer to Connecting
the power cord (2) on page 10.
Notes
!This mode is available when the rear view
camera setting is set to “On”. (For details,
refer to Operation Manual.)
!Connect this product to the rear view camera
only. Do not connect to any other
equipment.
<CRB4539-A>17
Engb 17
Section
02
Connection
Connection

Black plate (18,1)
Connecting the external
video component
Using AV input
You can connect an external video component
or external camera to this product.
Connecting an external camera
To video output
External camera
(sold separately)
This product
RCA cable
(sold separately)
Yellow
(VIDEO INPUT)
15 cm
Note
This mode is available when the setting of AV
input is set to “Camera”. (For details, refer to Op-
eration Manual.)
Connecting the video component
To video outputTo au di o outputs
External video
component
(sold separately)
This product
Red, white
(AUDIO INPUT)
RCA cables
(sold separately)
Yellow
(VIDEO INPUT)
23 cm 15 cm
Note
This mode is available when the setting of AV
input is set to “Source”. (For details, refer to Op-
eration Manual.)
<CRB4539-A>18
Engb
18
Section
02 Connection

Black plate (19,1)
Using an AUX input
To video output To audio outputs
External video
component
(sold separately)
This product
Red, white
RCA cables
(sold separately)
Yellow
AUX input
Mini-jack AV cable
(CD-RM10)
(sold separately)
Notes
!This mode is available when the setting of
AUX input is set to “On”. (For details, refer to
Operation Manual.)
!When connecting an external video compo-
nent using a mini-jack AV cable, use a sepa-
rately sold AUX extension cable as necessary.
CAUTION
Be sure to use a mini-jack AV cable (CD-RM10)
(sold separately) for wiring. If you use other
cables, the wiring position might differ resulting
in disturbed images and sounds.
OK
G
VR
L
G
RV
L
L : Left audio (White)
R : Right audio (Red)
V : Video (Yellow)
G : Earth
<CRB4539-A>19
Engb 19
Section
02
Connection
Connection

Black plate (20,1)
Connecting the rear display
To video inputTo audio inputs
Rear display with
RCA input jacks
(sold separately)
RCA cable
(sold separately)
Mini pin plug cable
(sold separately)
This product
Rear audio
output
Yellow (V OUT)
When using a rear display
connected to rear video output
WARNING
NEVER install the rear display in a location
that enables the driver to watch the video
source while driving.
This product’s rear video output is for connection
of a display to enable passengers in the rear
seats to watch the video source.
<CRB4539-A>20
Engb
20
Section
02 Connection