Pioneer Elite PRO-1000HDI User manual

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2003
PRO-1000HDI
ARP3187
PLASMA DISPLAY
PRO-1000HDI
THIS MANUAL IS APPLICABLETOTHE FOLLOWING MODEL(S) ANDTYPE(S).
This service manual should be used together with the following manual(s).
•Parts of the exploded views are all mentioned in this manual.
•The electrical parts are mentioned by contrast table in this manual.
(Refer to“3. Contrast of miscellaneous parts.”)
Model Type Power Requirement Remarks
PRO-1000HDI LUCXC AC120V
Model No. Order No. Remarks
PDP-503CMX/ LUCB ARP3150 SAFETY INFORMATION, EXPLODED VIEWS AND PARTS LIST , BLOCK
DIAGRAM, PCB PARTS LIST, ADJUSTMENT, IC INFORMATION etc.
ARP3152 SCHEMATIC DIAGRAM and PCB CONNECTION DIAGRAM
For details, refer to "Important symbols for good services" .
T-ZZY DEC. 2003 printed in Japan

PRO-1000HDI
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely,
you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts
must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
SAFETY PRECAUTIONS
NOTICE : Comply with all cautions and safety related notes
located on or inside the cabinet and on the chassis.
The following precautions should be observed :
1. When service is required, even though the PDP UNIT an
isolation transformer should be inserted between the power line
and the set in safety before any service is performed.
2. When replacing a chassis in the set, all the protective devices
must be put back in place, such as barriers, nonmetallic knobs,
adjustment and compartment covershields, isolation resistor-
capacitor, etc.
3. When service is required, observe the original lead dress. Extra
precaution should be taken to assure correct lead dress in the
high voltage circuitry area.
4. Always use the manufacture's replacement components.
Especially critical components as indicated on the circuit
diagram should not be replaced by other manufacture's.
Furthermore where a short circuit has occurred, replace those
components that indicate evidence of overheating.
5. Before returning a serviced set to the customer, the service
technician must thoroughly test the unit to be certain that it is
completely safe to operate without danger of electrical shock,
and be sure that no protective device built into the set by the
manufacture has become defective, or inadvertently defeated
during servicing. Therefore, the following checks should be
performed for the continued protection of the customer and
servicetechnician.
6. Perform the following precautions against unwanted radiation
and rise in internal temperature.
• Always return the internal wiring to the original styling.
• Attach parts (Gascket, Ferrite Core, Ground, Rear Cover,
Shield Case etc.) surely after disassembly.
7. Perform the following precautions for the PDP panel.
• When the front case is removed, make sure nothing hits the
panel face, panel corner, and panel edge (so that the glass does
not break).
• Make sure that the panel vent does not break. (Check that the
cover is attached.)
• Handle the FPC connected to the panel carefully.
Twisting or pulling the FPC when connecting it to the
connector will cause it to peel off from the panel.
8. Pay attention to the following.
• When the front case is removed, infrared ray is radiated and
may disturb reception of the remote control unit.
• Pay extreme caution when the front case and rear panel are
removed because this may cause a high risk of disturbance to
TVs and radios in the surrounding.

PRO-1000HDI 3
5678
5678
C
D
F
A
B
E
Leakage Current Cold Check
With the AC plug removed from anAC power source, place a
jumper across the two plug prongs. Turn theAC power switch on.
Using an insulation tester (DC 500V), connect one lead to the
jumpered AC plug and touch the other lead to each exposed metal
part (input/output terminals, screwheads, metal overlays, control
shafts, etc.), particularly any exposed metal part having a return
path to the chassis. Exposed metal parts having a return path to
the chassis should have a minimum resistor reading of 0.3MΩ
and a maximum resistor reading of 5MΩ. Any resistor value
below or above this range indicates an abnormality which
requires corrective action. Exposed metal parts not having a
return path to the chassis will indicate an open circuit.
Leakage Current Hot Check
Plug the AC line cord directly into an AC power source (do not
use an isolation transformer for this check).
Turn the AC power switch on.
Using a "Leakage Current Tester (Simpson Model 229
equivalent)", measure for current from all exposed metal parts of
the cabinet (input/output terminals, screwheads, metal overlays,
control shaft, etc.), particularly any exposed metal part having a
return path to the chassis, to a known earth ground (water pipe,
conduit, etc.). Any current measured must not exceed 0.5mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE SET TO THE CUSTOMER.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in PIONEER set have
special safety related characteristics. These are often not evident
from visual inspection nor the protection afforded by them
necessarily can be obtained by using replacement components
rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in this
Service Manual.
Electrical components having such features are identified by
marking with a on the schematics and on the parts list in this
Service Manual.
The use of a substitute replacement component which dose not
have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in this
Service Manual, may create shock, fire or other hazards.
Product Safety is continuously under review and new instructions
are issued from time to time. For the latest information, always
consult the current PIONEER Service Manual. A subscription to,
or additional copies of, PIONEER Service Manual may be
obtained at a nominal charge from PIONEER.
Leakage
current
tester
Reading should
not be above
0.5mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test

PRO-1000HDI
4
1234
1234
C
D
F
A
B
E
Charged Section
The places where the commercial AC power is used without
passing through the power supply transformer.
If the places are touched, there is a risk of electric shock. In
addition, the measuring equipment can be damaged if it is
connected to the GND of the charged section and the GND of the
non-charged section while connecting the set directly to the
commercial AC power supply. Therefore, be sure to connect the
set via an insulated transformer and supply the current.
1. AC Power Cord
2. AC Inlet with Filter
3. Power Switch (S1)
4. Fuse (In the SW POWER SUPPLY Module)
5. STB Transformer and Converter Transformer
(In the SW POWER SUPPLY Module)
6. Other primary side of the SW POWER SUPPLY Module
High Voltage Generating Point
The places where voltage is 100V or more except for the charged
places described above. If the places are touched, there is a risk of
electric shock.
1. SW POWER SUPPLY Module ...................................... (225V)
2. X DRIVE Assy ............................................... (–300V to 225V)
3. Y DRIVE Assy ................................................................(355V)
4. SCAN (A) Assy .............................................................. (355V)
5. SCAN (B) Assy .............................................................. (355V)
6. X CONNECTOR (A)Assy ............................ (–300V to 225V)
7. X CONNECTOR (B)Assy ............................ (–300V to 225V)
X CONNECTOR (B)
Assy
AC Inlet with Filter
Power Cord
Power Switch
(S1)
Y DRIVE
Assy
SCAN (A)
Assy
SCAN (B)
Assy
X CONNECTOR (A)
Assy
SW POWER SUPPLY
Module
Fig.1 Charged Section and High Voltage Generating Point (Rear View)
: Part is the High Voltage Generating Points
other than the Charged Section.
: Part is Charged Section.

PRO-1000HDI 5
5678
5678
C
D
F
A
B
E
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.

PRO-1000HDI
6
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION.....................................................................................................................................2
1. SPECIFICATIONS ............................................................................................................................................ 7
2. EXPLODED VIEWS AND PARTS LIST............................................................................................................8
2.1 PACKING ...................................................................................................................................................8
2.2 UNDER LAYER SECTION (1) .................................................................................................................10
2.3 UNDER LAYER SECTION (2) .................................................................................................................12
2.4 UNDER LAYER SECTION (3) .................................................................................................................14
2.5 UNDER LAYER SECTION (4) .................................................................................................................16
2.6 UNDER LAYER SECTION (5) .................................................................................................................17
2.7 UNDER LAYER SECTION (6) .................................................................................................................18
2.8 MIDDLE LAYER SECTION (1).................................................................................................................19
2.9 MIDDLE LAYER SECTION (2).................................................................................................................20
2.10 MIDDLE LAYER SECTION (3)...............................................................................................................21
2.11 MIDDLE LAYER SECTION (4)...............................................................................................................22
2.12 UPPER LAYER SECTION (1)................................................................................................................23
2.13 UPPER LAYER SECTION (2)................................................................................................................24
2.14 FRONT CASE SECTION (1)..................................................................................................................26
2.15 FRONT CASE SECTION (2)..................................................................................................................27
2.16 REAR SECTION....................................................................................................................................28
2.17 PANEL CHASSIS (50) ASSY (AWU1066) .............................................................................................28
3. CONTRAST OF MISCELLANEOUS PARTS..................................................................................................29
4. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM..........................................................................................30
4.1 BLOCK DIAGRAM...................................................................................................................................30
4.1.1 OVERALL DIAGRAM......................................................................................................................... 30
4.1.2 RGB ASSY ........................................................................................................................................32
4.1.3 VIDEO SIGNAL ROUTE....................................................................................................................34
4.1.4 SYNC SIGNAL ROUT .......................................................................................................................35
4.2 WAVEFORMS..........................................................................................................................................36
4.3 SCHEMATIC DIAGRAM........................................................................................................................... 42
4.3.1 I/O ASSY (1/2)...................................................................................................................................42
4.3.2 I/O ASSY (2/2)...................................................................................................................................44
4.3.3 RGB ASSY (1/10)..............................................................................................................................46
4.3.4 RGB ASSY (2/10)..............................................................................................................................48
4.3.5 RGB ASSY (3/10)..............................................................................................................................50
4.3.6 RGB ASSY (4/10)..............................................................................................................................52
4.3.7 RGB ASSY (5/10)..............................................................................................................................56
4.3.8 RGB ASSY (6/10)..............................................................................................................................60
4.3.9 RGB ASSY (7/10)..............................................................................................................................62
4.3.10 RGB ASSY (8/10)............................................................................................................................66
4.3.11 RGB ASSY (9/10)............................................................................................................................68
4.3.12 RGB ASSY (10/10)..........................................................................................................................70
4.3.13 VIDEO SLOT US2 ASSY (1/6) ........................................................................................................72
4.3.14 VIDEO SLOT US2 ASSY (2/6) ........................................................................................................74
4.3.15 VIDEO SLOT US2 ASSY (3/6) ........................................................................................................76
4.3.16 VIDEO SLOT US2 ASSY (4/6) ........................................................................................................78
4.3.17 VIDEO SLOT US2 ASSY (5/6) ........................................................................................................80
4.3.18 VIDEO SLOT US2 ASSY (6/6) ........................................................................................................82
5. PCB CONNECTION DIAGRAM .....................................................................................................................84
5.1 I/O ASSY..................................................................................................................................................85
5.2 RGB ASSY...............................................................................................................................................86
5.3 VIDEO SLOT US2 ASSY.........................................................................................................................90
6. PCB PARTS LIST ...........................................................................................................................................92
7. ADJUSTMENT ............................................................................................................................................... 98
7.1 SERVICE FACTORY MODE ....................................................................................................................98
7.1.1 State Transition Diagram.................................................................................................................... 98
7.1.2 Table of Adjustment Items in Service Factory..................................................................................101
7.1.3 Description of Service Factory Menu Display..................................................................................103
7.2 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED.....................................132
7.3 ADJUSTMENT.......................................................................................................................................133
7.3.1 VIDEO SLOT US2 ADJUSTMENT ..................................................................................................133
7.3.2 MAIN UNIT ADJUSTMENT.............................................................................................................136
7.4 COMMAND............................................................................................................................................141
7.4.1 RS-232C COMMANDS (for adjustment) .........................................................................................141
7.4.2 RS-232C COMMANDS (for setting) ................................................................................................142
7.4.3 GET COMMAND .............................................................................................................................145
8. GENERAL INFORMATION........................................................................................................................... 154
8.1 DIAGNOSIS...........................................................................................................................................154
8.1.1 CONFIGURATION OF THE PC BOARD......................................................................................... 154
8.1.2 DIAGNOSIS FOR SHUTDOWN AND POWER-DOWN BY LED.....................................................155
8.1.3 AUTOMATIC BACKUP OF DIGITAL VIDEO ASSY DATA................................................................ 165
8.1.4 PROTECTION OPERATION MODE................................................................................................167
8.1.5 DISASSEMBLY.....................................................................................................................................168

PRO-1000HDI 7
5678
5678
C
D
F
A
B
E
1. SPECIFICATIONS
General (PRO-1000HDI)
Light emission panel ............ 50 inch plasma display panel
Number of pixels .............................................. 1280 x 768
Power supply ........................................... AC 120 V, 60 Hz
Rated current ............................................................. 3.2 A
Standby power consumption ...................................... 1 W
External dimensions ... 1259 (W) x 776 (H) x 104.7 (D) mm
............................. 49-9/16 (W) x 30-9/16 (H) x 4-1/8 (D) in.
Weight............................................. 46.5 kg (102 lbs. 8 oz)
Input/output
Video
INPUT 1
Input Mini D-sub 15 pin (socket connector)
RGB signal (G ON SYNC compatible)
RGB ... 0.7 Vp-p/75 Ω/no sync.
HD/CS, VD ... TTL level
/positive and negative polarity
/2.2 kΩ
G ON SYNC
... 1 Vp-p/75 Ω/negative sync.
*Compatible with Microsoft’s Plug & Play
(VESA DDC1/2B)
Component video signal
Y ... 1 Vp-p/75 Ω/negative sync.
CB/PB, CR/PR
... 0.525 Vp-p/75 Ω
(75% satulation level)
Output Mini D-sub 15 pin (socket connector)
75 Ω/with buffer
INPUT 2
Input BNC jack (x5)
RGB signal (G ON SYNC compatible)
RGB ... 0.7 Vp-p/75Ω/no sync.
HD/CS, VD ... TTL level
/positive and negative polarity/
75 Ωor 2.2 kΩ
(impedance switch)
G ON SYNC ...
1 Vp-p/75 Ω/negative sync.
Component video signal
Y ... 1 Vp-p/75 Ω/negative sync.
CB/PB, CR/PR
... 0.525 Vp-p/75 Ω
(75% satulation level)
INPUT 3
Input S terminal (Mini DIN 4 pin)
• Y/C saparate video signal (NTSC)
Y . . . 1 Vp-p/75Ω/negative sync.
C . . . 0.286 Vp-p/75Ω
INPUT 4
Input BNC jack
• Composite video signal (NTSC)
1 Vp-p/75Ω/negative sync.
INPUT 5
Input HDMI jack
• Digital signal
3.3 V T.M.D.S. / 50 Ω
Audio
Input AUDIO INPUT (for INPUT 1/2)
Stereo mini jack
L/R ... 500mVrms/more than 10 kΩ
AUDIO INPUT (for INPUT 3)
Pin jack (x2)
L/R ... 500mVrms/more than 10 kΩ
AUDIO INPUT (for INPUT 4)
Pin jack (x2)
L/R ... 500mVrms/more than 10 kΩ
AUDIO INPUT (for INPUT 5)
Pin jack (x2)
L/R ... 500mVrms/more than 10 kΩ
Output AUDIO OUTPUT
Stereo mini jack
L/R ... 500mVrms (max)/less than 5 kΩ
SPEAKER
L/R ... 8 – 16 Ω/2W +2W (at 8 Ω)
Control
RS-232C ... D-sub 9 pin (pin connector)
COMBINATION IN/OUT
... Mini DIN 6 pin (x2)
CONTROL IN/OUT ... monaural mini jack (x2)
Warranty x1
Operating Instructions x1
Due to improvements, specifications and design are subject to
change without notice.
Power Cord x1
(ADG1208)
Remote Control Unit x1
(AXD1459) Binder Assy x1 (AEC1758)
Dry Cell Battery (R6P, AA)
Cleaning Cloth (for wiping front panel) x1
(AED1208)
Speed Clamp (×2)
Bead Bands (×2)
Accessories

PRO-1000HDI
8
1234
1234
C
D
F
A
B
E
2. EXPLODEDVIEWS AND PARTS LIST
2.1 PACKING
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
1
23
4
11
12
13
2
614
10
13
22
7
5
15
19
16
17
18
8
No.
SD
9
4
3
23
20 21

PRO-1000HDI 9
5678
5678
C
D
F
A
B
E
PACKING parts Lis
Mark No. Description Part No.
1Packing Case TOP AHD3208
2 Under Carton AHD3112
3 Corner Pad A AHA2288
4 Corner Pad B AHA2289
5 Vinyl Sheet 60 Under AHG1234
NSP 6 Poly Bag AHG1285
NSP 7 Dry Cell Battery (R6P, AA) AEX1026
8 Caution Sheet ARM1176
NSP 9 Warranty Card ARY1123
10 Front Sheet AHB1241
11 Cord Case AHC1037
>
12 Power Cord ADG1208
13 Vinyl Bag AHG1310
14 Accessory Case AHC1036
15 Operating Instructions ARB1560
(English)
16 Caution Sheet ARM1194
17 Caution Sheet ARM1203
18 Plasma Caution Sheet ARM1145
NSP 19 Card VRY1132
20 Binder Assy AEC1758
(Speed Clamp x 2, Bead Band x 2)
21 Cleaning Cloth AED1208
(forWiping Front Panel)
22 Remote Control Unit AXD1459
23 Battery Cover AZN2462

PRO-1000HDI
10
1234
1234
C
D
F
A
B
E
2.2 UNDER LAYER SECTION (1)
UNDER LAYER SECTION (1) parts List
11
1
10 10
11
2
Refer to
next page.
4
10
11
3
67666
Upper side
6
8
9
9
8
6
67
6
5
10
1112
7
Mark No. Description Part No.
1 CLAMP A Assy AWZ6738
2 CLAMP B Assy AWZ6739
3 CLAMP C Assy AWZ6740
4 CLAMP D Assy AWZ6741
5 Service Panel Assy AWU1068
6 Wire Saddle AEC1904
7 Circuit Board Spacer AEC1872
8 Circuit Board Spacer AEC1873
NSP 9 PCB Spacer AEC1121
10 Locking Card Spacer AEC1736
11 Screw ABA1301
12 V Cushion AED1205
Mark No. Description Part No.

PRO-1000HDI 11
5678
5678
C
D
F
A
B
E
Caution in Replacement of Panel Chassis (50) Assy
Service Panel Assy (AWU1068) is all common use parts of for business, public use and module.
Supply it by the state that installed Circuit Board Spacer (AEC1872) and Wire Saddle (AEC1904)as follows.
Therefore need to remove it in accordance with model.
Confirm character carved a seal near the parts, and remove it.
P:Public exclusive use
W:Module exclusive use
PW : Common use of public use and module
∗In case of this unit, all the parts carved a seal of character removes it.
Wire Saddle
(AEC1904)
Service Panel Assy (AWU1068)
Circuit Board Spacer
(AEC1872) Circuit Board Spacer (AEC1872)
(There is marking of "P" nearby.)

PRO-1000HDI
12
1234
1234
C
D
F
A
B
E
2.3 UNDER LAYER SECTION (2)
Upper side
15
11
9
481
2
73
5 or 6
10
236 4
11 9
10
7 or 8
10
1010

PRO-1000HDI 13
5678
5678
C
D
F
A
B
E
UNDER LAYER SECTION (2) parts List
Mark No. Description Part No.
NSP 1 ADR CONNECT A Assy AWZ6626
NSP 2 ADR CONNECT B Assy AWZ6627
NSP 3 ADR CONNECT C Assy AWZ6628
NSP 4 ADR CONNECT D Assy AWZ6629
5 BRIDGE A Assy AWZ6734
6 BRIDGE B Assy AWZ6735
7 BRIDGE C Assy AWZ6736
8 BRIDGE D Assy AWZ6737
9 ADR RESONANCE Assy AWZ6750
10 Screw ABA1301
11 Screw VBB30P100FNI

PRO-1000HDI
14
1234
1234
C
D
F
A
B
E
2.4 UNDER LAYER SECTION (3)
5
4
33
1111
1010
1010
14
14
14
14
13
13
13
13
13
13
13
13
Upper side
1
721 20
8 8
19
9
13 13 15
1317 1318
16
77
77
1212
1212 1212
14
14
14
14
22
22
236

PRO-1000HDI 15
5678
5678
C
D
F
A
B
E
UNDER LAYER SECTION (3) parts List
Mark No. Description Part No.
1 DIGITAL VIDEO Assy AWV2072
2 MX AUDIO Assy AWZ6644
3XDRIVE Assy AWV1984
NSP 4 X CONNECTOR (A) Assy AWZ6732
NSP 5 X CONNECTOR (B) Assy AWZ6733
6 Sheet D AEC1985
7 Flat Clamp AEC1879
NSP 8 Metal Fittings ANG2464
NSP 9 Heat Sink ANH1594
10 Coil Silicone Sheet AEH1048
11 Circuit Board Spacer AEC1872
12 Screw ABZ30P060FMC
13 Screw VBB30P100FNI
14 Screw PMB30P060FNI
15 J201 Flexible Flat Cable ADD1183
16 J202 Flexible Flat Cable ADD1183
17 J209 Flexible Flat Cable ADD1191
18 J204 Flexible Flat Cable ADD1196
19 J210 Flexible Flat Cable ADD1190
20 J211 Flexible Flat Cable ADD1186
21 J212 Flexible Flat Cable ADD1188
22 Audio Sheet AMR3305

PRO-1000HDI
16
1234
1234
C
D
F
A
B
E
2.5 UNDER LAYER SECTION (4)
UNDER LAYER SECTION (4) parts List
Bottom side
2
9
22 20
1010
1515
1515
1515
17
17
17
17
18
18
18
18
18
18
18
18
17
17
17
17
1414 55
2
4
3
11
12
17
17
13
2121
21
23
21
2828
1416 1416
1416
7777
14191419 77
Mark No. Description Part No.
1 DIGITAL VIDEO Assy AWV2072
2YDRIVE Assy AWZ6745
NSP 3 SCAN (A) Assy AWZ6722
NSP 4 SCAN (B) Assy AWZ6723
5 SENSOR Assy AWZ6696
6•• • • •
7 Flat Clamp AEC1879
NSP 8 Metal Fittings ANG2464
NSP 9 Heat Sink ANH1594
10 Coil Silicone Sheet AEH1048
11 Scan IC Spring (L) ABK1026
12 Scan IC Spring (R) ABK1027
13 Scan Insulation Sheet AMR3271
14 Rivet BEC1066
15 Circuit Board Spacer AEC1872
16 Screw ABZ30P060FMC
17 Screw PMB30P060FNI
18 Screw VBB30P100FNI
19 J208 Flexible Flat Cable ADD1191
20 J207 Flexible Flat Cable ADD1190
21 J203 Flexible Flat Cable ADD1184
22 J205 Flexible Flat Cable ADD1189
23 J206 Flexible Flat Cable ADD1187
Mark No. Description Part No.

PRO-1000HDI 17
5678
5678
C
D
F
A
B
E
2.6 UNDER LAYER SECTION (5)
UNDER LAYER SECTION (5) parts List
8
9
10
11
11
11
11 4
2 (Upper Side)
1
1312 3 (Bottom Side)
11
1414
Bottom side
5
66
Mark No. Description Part No.
1 ADR RESONANCE Assy AWZ6750
2 SUB ADDRESS A Assy AWZ6689
3 SUB ADDRESS B Assy AWZ6690
4 Circuit Board Spacer AEC1873
5Power Sheet AMR3291
6 Rivet BEC1066
7•• • • •
NSP 8 Fan Metal ANG2465
9Fan Motor AXM1040
10 Screw PPZ50P100FZK
11 Screw ABZ30P060FMC
NSP 12 Heatsink ANH1594
13 Silicone Sheet AEH1039
14 Insulating Sheet AMR3343
Mark No. Description Part No.

PRO-1000HDI
18
1234
1234
C
D
F
A
B
E
2.7 UNDER LAYER SECTION (6)
MIDDLE LAYER SECTION (1) parts List
Y1Y2
D18
D1
D16
D10
D11
D15
D14
D13D12 D17
SA1SA2
A6
A3
A5
A1
X1
D12
X2
TE1
SA2SA1
D6 D7
D2
D3
D8 D9
Upper side 1 16 2 10 5 3 4
17
18
433521
15
14
13
12
24
27
26
6 11533 22 7 31
20
30
19
28
23
29 32258 9 3434
Mark No. Description Part No.
NSP 1 ADR CONNECT A Assy AWZ6626
NSP 2 ADR CONNECT B Assy AWZ6627
NSP 3 ADR CONNECT C Assy AWZ6628
NSP 4 ADR CONNECT D Assy AWZ6629
5 ADR RESONANCE Assy AWZ6750
6 BRIDGE A Assy AWZ6734
7 BRIDGE B Assy AWZ6735
8 BRIDGE C Assy AWZ6736
9 BRIDGE D Assy AWZ6737
10 SUB ADDRESS A Assy AWZ6689
11 SUB ADDRESS B Assy AWZ6690
NSP 12 SCAN (A) Assy AWZ6722
NSP 13 SCAN (B) Assy AWZ6723
14 Y DRIVE Assy AWZ6745
15 DIGITAL VIDEO Assy AWV2072
16 SENSOR Assy AWZ6696
17 X CONNECTOR (A) Assy AWZ6732
18 X CONNECTOR (B) Assy AWZ6733
19 X DRIVE Assy AWV1984
20 MX AUDIO Assy AWZ6644
21 • • • • •
22 Flat Clamp AEC1879
23 J115 3P Housing Wire ADX2705
24 J110 3P Housing Wire ADX2704
25 J108 8P Housing Wire ADX2811
26 J101 Wire F ADX2695
27 J102 Wire E ADX2782
28 J103 13P Housing Wire ADX2700
29 J116 4P Housing SP Wire ADX2756
30 J109 Wire G ADX2696
31 J111 Wire I ADX2698
32 J104 Wire H ADX2697
33 J117 4P Housing SP Wire ADX2756
34 Binder AEC-093
35 J118 5P Housing Wire ADX2776
Mark No. Description Part No.

PRO-1000HDI 19
5678
5678
C
D
F
A
B
E
2.8 MIDDLE LAYER SECTION (1)
MIDDLE LAYER SECTION (2) parts List
1
12 7
7
11
11
6
11
14
11
12
1
2
6
10
13 13 13 13 13
9
9
9
4
3
5
15
9
8
8
88
99
99
9
7
7
13 13 13 13 13
9
99
4
3
5
15
9
8
8
88
99
10
99
9
7
7
Mark No. Description Part No.
1 Card Corner Holder BEC1144
2 Niplocker BEC1136
NSP 3 Front Chassis H ANA1683
4 Sub Frame L ANG2455
5 Sub Frame R ANG2456
6 FPC Cushion AEB1370
NSP 7 Front Chassis V ANA1661
8 Screw AMZ30P060FZK
9 Screw ABA1294
10 Screw BMZ30P060FMC
11 V Cushion AED1205
12 Gasket R ANK1695
NSP 13 Spacer AEC1902
14 Seet C AEC1927
NSP 15 Front Chassis HU ANA1697
Mark No. Description Part No.

PRO-1000HDI
20
1234
1234
C
D
F
A
B
E
2.9 MIDDLE LAYER SECTION (2)
MIDDLE LAYER SECTION (2) parts List
37
29
9
4
5
1
9
8
10
10
6
6
11
11
Mark No. Description Part No.
1 IR Assy AWZ6643
2 MX LED Assy AWZ6642
3 J113 Wire J ADX2699
4 KEY CONNECTOR Assy AWZ6695
NSP 5 IR Holder ANG2494
6 Nyron Rivet AEC1671
7 J111 Wire I ADX2698
NSP 8 Switch Holder ANG2493
9 Screw BMZ30P040FMC
10 Screw ABZ30P050FZK
11 Gasket R ANK1695
Mark No. Description Part No.