Pioneer AVH-P4150DVD User manual

<CRD4379-A> <1>
English
Installation Manual
설치 설명서
DVD AV RECEIVER
DVD AV 接收機
DVD AV 수신기
AVH-P4150DVD
한글
中文
CRD4379ANinst.indb1CRD4379ANinst.indb1 2008/10/0915:25:402008/10/0915:25:40

2
<CRD4379-A> <2>
Contents
Connecting the units ............................ 3
Parts supplied .................................................. 5
Connecting the power cord ............................... 6
When connecting to
separately sold power amp........................ 8
When connecting
with supplied USB cable ............................9
When connecting
with optional CD-IU200V cable ..................9
When connecting
with a rear view camera............................ 10
When connecting
with a multi-channel processor ...............11
Connecting and installing
the optical cable connection box.............12
Connecting the optical cable .................................12
Installing the optical cable connection box..........12
When connecting the external
video component and the display............ 13
When using a display connected to
rear video output............................................13
Installation ........................................... 14
Installation using the screw holes
on the side of the unit ............................. 14
CRD4379ANinst.indb2CRD4379ANinst.indb2 2008/10/0915:25:422008/10/0915:25:42

3
<CRD4379-A> <3>
English
Connecting the units
WARNING
• To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or
TV (sold separately) feature should never be
used while the vehicle is being driven. Also, rear
displays should not be in a location where it is a
visible distraction to the driver.
• In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit’s DVD features should not be used.
CAUTION
• PIONEER does not recommend that you
install or service your display yourself.
Installing or servicing the product may
expose you to risk of electric shock or other
hazards. Refer all installation and servicing
of your display to authorized Pioneer service
personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wiring
to remain exposed.
• Do not drill a hole into the engine
compartment to connect the yellow lead
of the unit to the vehicle battery. Engine
vibration may eventually cause the insulation
to fail at the point where the wire passes from
the passenger compartment into the engine
compartment. Take extra care in securing the
wire at this point.
• It is extremely dangerous to allow the display
lead to become wound around the steering
column or gearshift. Be sure to install the
display in such a way that it will not obstruct
driving.
• Make sure that wires will not interfere with
moving parts of the vehicle, such as the
gearshift, parking brake or seat sliding
mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work properly.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR
IS DESIGNED TO DETECT PARKED STATUS
AND MUST BE CONNECTED TO THE POWER
SUPPLY SIDE OF THE PARKING BRAKE SWITCH.
IMPROPER CONNECTION OR USE OF THIS
LEAD MAY VIOLATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.
CRD4379ANinst.indb3CRD4379ANinst.indb3 2008/10/0915:25:422008/10/0915:25:42

4
<CRD4379-A> <4>
Connecting the units
Note
• This unit cannot be installed in a vehicle without
ACC (accessory) position on the ignition switch.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s
negative cables.
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
booster power supply terminal.
• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect
it to the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product’s ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
CRD4379ANinst.indb4CRD4379ANinst.indb4 2008/10/0915:25:432008/10/0915:25:43

5
<CRD4379-B> <5>
English
Connecting the units
Parts supplied
This product Power cord USB cable
Frame Flush surface screw
(5 mm × 8 mm) (8 pcs.)
Binding screw
(5 mm × 8 mm) (8 pcs.)
Touch panel pen Remote control unit
CRD4379BNinst.indb5CRD4379BNinst.indb5 2008/11/1014:31:052008/11/1014:31:05

6
<CRD4379-A> <6>
Connecting the units
Connecting the power cord










Yellow
Connect to the constant 12 V supply terminal.
Fuse resistor
Red
Connect to terminal controlled by ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Left Right
Front speaker Front speaker
Rear speaker or
Subwoofer (4 Ω)
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Violet
Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not
connect anything to Green and Green/black leads.
Subwoofer (4 Ω)
× 2
Rear speaker or
Subwoofer (4 Ω)
Fuse (10 A)
Antenna input
Orange/white
Connect to lighting switch terminal.
Fuse resistor
Use a mini plug cable to
connect with auxiliary
device
AUX jack (3.5 ø)
This product
CRD4379ANinst.indb6CRD4379ANinst.indb6 2008/10/0915:25:472008/10/0915:25:47

7
<CRD4379-A> <7>
English
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Yellow/black
If you use equipment with Mute function, wire this lead to the
Audio Mute lead on that piece of equipment. If not, keep the
Audio Mute lead free of any connections.
Light green
Used to detect the ON/OFF status of the parking
brake. This lead must be connected to the power
supply side of the parking brake switch.
Blue/white
Connect to system control terminal of the power amp or
auto-antenna relay control terminal (max. 300 mA 12 V DC).
Ground side
Power supply side
Parking brake
switch
Fuse resistor
With a 2 speaker system, do not connect anything to the speaker leads
that are not connected to speakers.
Note:
· Change the initial setting of this unit (refer
to the Operation Manual). The subwoofer
output of this unit is monaural.
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
When you connect the separately sold
multi-channel processor (e.g., DEQ-P7650) to
this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
Connecting the units
CRD4379ANinst.indb7CRD4379ANinst.indb7 2008/10/0915:25:482008/10/0915:25:48

8
<CRD4379-A> <8>
Connecting the units
When connecting to separately sold power amp












Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
When you connect the separately sold
multi-channel processor (e.g., DEQ-P7650) to
this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
This product
Connect with RCA cables
(sold separately)
Rear speaker
Perform these connections when
using the optional amplifier.
System remote control
Front speaker Front speaker
Left Right
Front output
When you connect the multi-channel processor
to this unit, refer to multi-channel processor’s
installation manual for the connection method.
Rear speaker
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Subwoofer Subwoofer
Rear output
Subwoofer output
To front output
To rear output
To subwoofer
output
CRD4379ANinst.indb8CRD4379ANinst.indb8 2008/10/0915:25:492008/10/0915:25:49

9
<CRD4379-A> <9>
English
Connecting the units
When connecting with supplied USB cable
This product
1.5 m
USB cable
Connect to sparately sold
USB device.
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS cable
(Supplied with Bluetooth adapter)
Black
Bluetooth adapter
(e.g. CD-BTB100)
(sold separately)
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
Blue
IP-BUS input
1.5 m
When connecting with optional CD-IU200V cable
This product
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
Dock connector
Interface cable
(CD-IU200V) (sold separately)
iPod with video capabilities
(sold separately)
IP-BUS cable
(Supplied with Bluetooth adapter)
Black
Bluetooth adapter
(e.g. CD-BTB100)
(sold separately)
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
IP-BUS input
USB input
AUX input (AUX IN)
1.5 m
CRD4379ANinst.indb9CRD4379ANinst.indb9 2008/10/0915:25:512008/10/0915:25:51

10
<CRD4379-A> <10>
Connecting the units
When connecting with a rear view camera
When this product is used with a rear view camera, it is possible to automatically switch
from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
• The screen image may appear reversed.
• The rear view camera function is to be used as an aid for backing into a tight parking spot.
Do not use this function for entertainment purposes.
• Objects in the rear view may appear closer or more distant than they actually are.
RCA cable
(sold separately)
To video output
Rear view camera
Rear view camera input
(REAR CAMERA IN)
This product
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
You must use a camera
which outputs mirror
reversed images.
CAUTION
Fuse resistor
• It is necessary to set Camera Porality properly in System Menu when connecting the rear
view camera.
CRD4379ANinst.indb10CRD4379ANinst.indb10 2008/10/0915:25:522008/10/0915:25:52