Pioneer SX-10AE User manual

SX-10AE
STEREO RECEIVER
Instruction Manual
En
SN29403247_SX-10AE_En_1707XX.book 1 ページ ２０１７年７月１９日 水曜日 午後１時５９分

2
Before Start
Table of Contents
Before Start............................................................. 2
What's in the box .....................................................3
Part Names .............................................................4
Part Names .............................................................4
Install....................................................................... 8
Step1: Connect the Speakers .................................8
Step2: Connect an other External Device ...............9
Step3: Connect Other Cables ...............................10
Playback ............................................................... 11
Playing Audio from a Connected Device .............. 11
BLUETOOTH
®
Playback ......................................12
Listening to the AM/FM Radio................................13
Registering a Station ............................................. 15
Naming Radio Stations Registered as Presets ..... 16
Adjusting the Sound Quality ..................................17
Setup ..................................................................... 18
Setup Menu ...........................................................18
Others .................................................................. 21
Troubleshooting .................................................... 21
General Specifications .......................................... 23
> Before Start > Part Names > Install > Playback
Setup | Others
SN29403247_SX-10AE_En_1707XX.book 2 ページ ２０１７年７月１９日 水曜日 午後１時５９分

3
En
What's in the box
1. Main unit (1)
2. Remote controller (RC-963R) (1), batteries (AAA/R03)
(2)
3. FM indoor antenna (1)
4. AM indoor antenna (1)
≥Instruction Manual (This document) (1)
0Connect speakers with 4 ≠ to 16 ≠ impedance. Note that
when connecting to both SPEAKERS A and B terminals,
connect speakers with 8 ≠ to 16 ≠ impedance to both A
and B.
0The power cord must be connected only after all other
cable connections are completed.
0We will not accept responsibility for damage arising from
the connection of equipment manufactured by other
companies.
0Specifications and appearance are subject to change
without prior notice.
> Before Start > Part Names > Install > Playback
Setup | Others
32
4
1
SN29403247_SX-10AE_En_1707XX.book 3 ページ ２０１７年７月１９日 水曜日 午後１時５９分

4
Part Names
Part Names
Front Panel
1. ÍSTANDBY/ON button
2. SPEAKERS A/B button: Select the terminals to output audio from between SPEAKERS
A/B.
3. DIRECT button: Switches to the DIRECT mode which outputs pure sound as it was
intended.
4. Display (P5)
5. Remote control sensor: Receives signals from the remote controller.
0The signal range of the remote controller is within about 16y/5 m, at an angle of 20° on
the perpendicular axis and 30° to either side.
6. Bluetooth indicator: Lights when the unit is connected by BLUETOOTH. It will flash during
pairing or if the connection is not correct.
7. MEMORY button: Used to register AM/FM radio stations (P15).
8. TUNING/PRESET button: Switch between the TUNING mode, where you select a
frequency to tune to a station, and the PRESET mode, where you select a preset station.
9. VOLUME
10. PHONES jack: Connect stereo headphones with a standard plug (Ø1/4z/6.3 mm).
11. Input Selector buttons: Switches the input to be played.
12. TONE button: Switches to the TONE mode which enables BASS and TREBLE. After
switching to the TONE mode, press again to see the settings for "Bass", "Treble", and
"P.BASS" with each press.
13. buttons: Used to tune to AM/FM stations, select preset numbers, and to
adjust the sound quality.
14. BALANCE button: Adjusts the balance of the sounds output from the left and right
speakers (P17).
> Before Start >PartNames > Install > Playback
Setup | Others

     

SN29403247_SX-10AE_En_1707XX.book 4 ページ ２０１７年７月１９日 水曜日 午後１時５９分

5
> Before Start >PartNames > Install > Playback
Setup | Others
En
Display
1. The currently selected speaker system lights.
2. Lights when headphones are connected.
3. Lights in the following conditions.
PRESET: PRESET mode has been selected with
TUNING/PRESET on the main unit.
RDS (European and Australian models): Receiving
RDS broadcasting.
AUTO: When tuning mode is auto.
1TUNED2: Receiving AM/FM radio.
FM STEREO: Receiving FM stereo.
4. Flashes when muting is on.
5. Displays radio and a variety of other information.
6. Lights in the following conditions.
SLEEP: Sleep timer has been set.
ASb: Auto Standby has been set.
Hz: May light while "Tuner Setting" in the Setup menu
is being set.




SN29403247_SX-10AE_En_1707XX.book 5 ページ ２０１７年７月１９日 水曜日 午後１時５９分

6
Rear Panel
1. FM UMBAL 75Ω/AM LOOP ANTENNA terminals: Connect the supplied FM indoor
antenna and AM indoor antenna.
2. PRE OUT SUBWOOFER jack: Connect a powered subwoofer with a subwoofer cable.
3. SPEAKERS jacks: Connect speakers with speaker cables. You can connect a set of left
and right speakers to each of the A/B terminals.
4. Power cord
5. AUDIO IN jacks: Input audio signals from an other external device with an analog audio
cable.
6. LINE OUT jacks: Connect a recording device, such as a cassette tape deck. Connect to
the AUDIO IN jacks on the recording device using analog audio cable.
> Before Start >PartNames > Install > Playback
Setup | Others
 


SN29403247_SX-10AE_En_1707XX.book 6 ページ ２０１７年７月１９日 水曜日 午後１時５９分

7
En
Remote Controller
1. ÍSTANDBY/ON button
2. SLEEP button: Set the sleep timer (P20).
3. INPUT SELECTOR buttons: Switches the input to be played.
4. Numbered buttons
5. DIRECT TUNING button: Use to select the number of a preset station or to directly input
the frequency of the station.
6. button: Temporarily mutes audio. Press again to cancel muting.
7. VOLUME buttons
8. Cursors (Up / Down / Left / Right), ENTER button: Select the item with the cursors and
press ENTER to confirm.
9. SETUP button: You can show advanced setting items on the display to provide you with
an even better experience (P18).
10. BASS buttons: Enhance or moderate the bass range (P17).
11. TREBLE buttons: Enhance or moderate the treble range (P17).
12. DISPLAY button: Switches the information on the display.
13. DIMMER button: You can adjust the brightness of the display in three steps. It cannot be
turned off completely.
14. buttons: Select the input to be played. The input changes CD  NETWORK 
LINE 1  LINE 2  FM  AM  BLUETOOTH each time you press the button.
15. CLEAR button: Deletes all characters you have entered when entering text.
16. PAIRING button: Used to connect to another BLUETOOTH wireless technology enabled
device (P12).
17. PRESET buttons: Used to select AM/FM radio stations (P15).
18. RETURN button: Returns the display to the previous state during setting.
19. DIRECT button: Switches to the DIRECT mode which outputs pure sound as it was
intended (P17).
20. TONE button: Switches to the TONE mode which enables BASS and TREBLE (P17).
> Before Start >PartNames > Install > Playback
Setup | Others



















SN29403247_SX-10AE_En_1707XX.book 7 ページ ２０１７年７月１９日 水曜日 午後１時５９分

8
Install
Step1: Connect the Speakers
You can connect two systems, Speaker A and Speaker B,
as the Speaker System. When connecting only one set,
connect to the SPEAKERS A terminals. With one set, use
speakers with 4 ≠ to 16 ≠ impedance.
Note that when connecting to both SPEAKERS A and B
terminals, connect speakers with 8 ≠ to 16 ≠ impedance to
both A and B.
Connect the speaker cable so the wires do not protrude
from the speaker jacks. If the exposed wires of the
speakers touch the rear panel or the + and – wires touch
each other, the protection circuit will be activated.
(*)You can also connect a powered subwoofer to the PRE
OUT SUBWOOFER jack to boost bass playback even
more. Use a subwoofer cable for connection.
> Before Start > Part Names >Install > Playback
Setup | Others
a
a
5/8˝
(15 mm)
Speaker B
Speaker A
*
Right Left Right Left
a Speaker Cable
Setup
0When connected as a Speaker B System, you
can output the same audio as Speaker A System
by switching with A/B/A+B. Press SPEAKER A/B
on the main unit to switch. The selection changes
in the order SPEAKER A, SPEAKER B,
SPEAKER A+B, Off with each press.
0If any of the connected speakers have an
impedance of 4 ≠ or more to less than 6 ≠, or
when a Speaker B system is to be used, press
SETUP (P7) on the remote controller, and set "SP
Impedance" to "4 ohm".
SN29403247_SX-10AE_En_1707XX.book 8 ページ ２０１７年７月１９日 水曜日 午後１時５９分

9
En
Step2: Connect an other External Device
AUDIO IN connection
Connect an other external device with an analog audio
cable.
> Before Start > Part Names >Install > Playback
Setup | Others
CD
a
Network Audio
Player
a Analog Audio Cable
SN29403247_SX-10AE_En_1707XX.book 9 ページ ２０１７年７月１９日 水曜日 午後１時５９分

10
Step3: Connect Other Cables
Antenna Hookup
Move the antenna around while playing the radio to find the
position with the best reception.
Power Cord Hookup
The power cord must be connected only after all other
connections are completed.
> Before Start > Part Names >Install > Playback
Setup | Others
b
a
a
FM
AM
(North American
models)
(European and
Australian models)
a FM indoor antenna, b AM indoor antenna
SN29403247_SX-10AE_En_1707XX.book 10 ページ ２０１７年７月１９日 水曜日 午後１時５９分