Pioneer vsx-9900s User manual

Operating
Instructions
@) PIONEER smovece ern samen VSX-9900S
UEC
B03195
AUDIO/VIDEO STEREO RECEIVER
VSX-9900S
Thank you for buying this Pioneer product.
Please
read
through
these
operating
instructions
so
you
will
know
how
to
operate
your
model
properly.
After
you
have
finished
reading
the
instructions,
put
them
away
in
a
safe
place
for
future
reference.
In
some
countries
or
regions,
the
shape
of
the
power
plug
and
power
outlet
may
sometimes
differ
from
that
shown
in
the
explanatory
drawings.
However,
the
method
of
connecting
and
operating
the
unit
is the same.
WARNING: To PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear panel.
Please write this serial number on your enclosed warranty card and
keep it in a secure area. This is for your security.
[For Canadian model]
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
ATTENTION: Pour PREVENIR LES CHOCS ELECTRIQUES NE
PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR
UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT,
SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN
LAISSER AUCUNE PARTIE A DECOUVERT.
RETURN function
This
function
returns
the
unit
to a
set
of
initial
settings
amd
ready
to
broadcast
tuner.
This
is
helpful
during
troubleshooting
or
when
no
sound
is
output.
For
details,
refer
to
“‘FRONT
PANEL
FACILITIES,”’
page
19.
RESET function
Use this function when normal operation becomes ins possible
because of external influences such as static electricity orlgghtning,
or
when
operation
is
impossible
even
when
operation
swtches
are
pressed.
Press
the
reset
button
to
return
to
normal
operating
conditions.
If you press this button, the entire contents of the memory are
cleared.
About the Demonstration Mode
¢
The
demonstration
is
activated
by
turning
on
the
powes
switch
while
holding
down
the
RETURN
button
(from
power
standby
condition).
The
demonstration
will
appear
on
the
dispasy.
¢ Press any other switch to cancel the demonstration.
Y)
PIONEER’
The
Art
of
Entertainment

IMPORTANT
The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “‘dangerous vottage’’ within the product's
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
READ INSTRUCTIONS -- All the safety and operating
instructions should be read before the appliance is
operated.
RETAIN INSTRUCTIONS — The operating instructions
should be retained for future reference.
HEED WARNING — All warnings on the appliance and in
the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS — All operating and use in-
structions should be followed.
WATER AND MOISTURE — The appliance shoutd not
be used near water — for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet base-
ment, or near a swimming pool, etc.
LOCATION ~ The appliance should be installed in a
stable location.
WALL OR CENING MOUNTING — The apptiance
should not be mounted to a wall or ceiling.
VENTILATION -- The appliance should be situated so
that its location or position does not interfere with
its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or,
placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through
the ventilation openings.
HEAT — The appliance should be situated away from
heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers)
that produce heat.
POWER SOURCES — The appliance should be con-
nected to a power supply only of the type de-
scribed in the operating instructions or as marked
on the appliance.
POWER-CORD PROTECTION — Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them. Pay particular attention to cords at
Plugs, convenience receptacles, and the point
where they exit from the appliance.
POLARIZATION — If your purchased product is pro-
vided with a polarized power plug, please read the
following instructions. This product is equipped
with a polarized alternating current tine plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a
safety feature. If you are unabie to insert the plug
fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
CLEANING - The appliance should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or
other volatile liquids since they may corrode the
cabinet.
CAUTION
RISK OF ELECTRIC SHOCK
folem lonmel sy
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exciamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
SAFETY INSTRUCTIONS
POWER LINES — An outdoor antenna should be located
away from power lines.
NONUSE PERIODS — The power cord of the appliance
should be unplugged from the outlet when left un-
used for a long period of time.
OBJECT AND LIQUID ENTRY — Care should be taken
so that objects do not fall and liquids are not spilled
into the enclosure through openings.
DAMAGE REQUIRING SERVICE — The appliance
should be serviced by a Pioneer authorized service
center or qualified service personnel when:
The power-supply cord or the plug has been dam-
aged.
Objects have fallen, or liquid has been spilled into
the appliance.
The appliance has been exposed to rain.
The appliance does not appear to operate normally
or exhibits a marked change in performance.
The appliance has been dropped or the enclosure
damaged.
SERVICING — The user should not attempt to service
the appliance beyond that described in the opera-
ting instructions. For all other servicing, contact the
nearest Pioneer authorized service center.
OUTDOOR ANTENNA GROUNDING — if an outside an-
tenna is connected to the antenna terminal, be sure
the antenna system is grounded so as to provide
some protection against voltage surges and built
up static charges.
in the U.S.A. section 810 of the National Electrical
Code, ANSI/NFPA No. 70-1984, provides informa-
tion with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and require-
ments for the grounding electrode. See Fig. A.
CART — An appliance and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
NEC —NATIONAL ELECTRIC CODE
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 ~ 20)
ELECTRIC
SERVICE GROUNDING CONDUCTORS
EQUIPMENT (NEC SECTION 810 — 21}
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
FIG. A (NEC ART 250, PART H)
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-22 of the NEC that provides guidelines for proper grouncling
and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable emtry
as practical.
2
<ARB1332>

CONTENTS
BEFORE OPERATING, ADJUST THE POSITION OF THESE SWITCHES ...........cceceseeeeseeeeseseeterereenes 4
FEA TURES 222 cis sdehecsa cet teandetessceigg vouledc av acteee soevanas dice tasen sudees de de uceeasaduae vues gubescesdedswasy ves oot 4
BLOCK. DIAGRAM i235. Sascexsdeanevashcncdicseiaviverdeut best soecnedsceiwastuviocseGusaniaeessemen te agave chotedea seine dete 5
ACCESSORY: ITEMS scsicciccdies ick i oecdocttedinacccs soleeiSccawesudeavaaee versie gets basis vaGha dees vedehus evealt -eategees 5
DSSS (Digital Simulated Stereo System)............. ccc ccc eeeecee cee eeeeeeneesaeeeeteaeeeeeeeeeeeeneseeeeeaseaerseoens 5
SURROUND MODE tssesiccsccvcdscse saclécsdesecddar bots ndaaatce aes ceucsdeededeuecvevacncdveaeee ss cucaardeeudepencete vyesews 6
Sigel latucrebusttiie dy esttlesteigiatotests ince cael elem Redcat ik 7
FRONT PANEL: FACILIFIES iss ice sued ccctesucuessue tases yeas cltivvees cecdadicnul pewevevaan evaceutegastertda setegureceedes 19
REAR PANEL FACILITIES csscsicceccasisevesanncsesces ddatoneewe vbeceotat cgaasada cece sdetdddeteacaeddvesedeaden¥enzesctions 23
eas aite cag boas aisoaa ciel siaare SoRa gi aceasta elute hunch tera duke fiat asvaduasuensian eles 26
MANUAL TUNING Goscicsevicesvssccsavelssveuserieciaacecesteadtaeteteecvaeiabeutecucsvinaiayiwedssdeesstetebdteweeebedys 26
AUTO: TUNING bcc cadiscecstoaashedenceedcadevatesddueeevedeeaiiels eccsancnsacsdvacudessehossuacbls Costes ssbiuvestadereeceexes 26
DIRECT. ACCESS: TUNING sonic cccisvsctivacevasicdvavenebstcos geese catievesdedeadwcseoncesataaagaa tesa seeenesneteretecsenss 26
PRESET. TUNING ccisscccicccccsesecdsvssvescsdcagescee sus deucusasucoecacucesavdausecdeaniaued ud ces de¥edeas-n¥sduacsewaavess 27
NAMING A STATION i isviss ccs sieeascecosee leas sudacteendbcasvandasceevcta ducsesbebasdveiaduevesdetencdedssueensaudecrees 28
HITS (Hyper tntelligent Tuning System) ............c.cceeccseneseeneteeeecueeeeeeeeecesecenenensersesensanesaness 29
sesh paepea Bec er slaea ad att ae Oatcd ect rah ae 29
PEAY. BAGK fciec2sscccackcsuces css ceca sabeckalwisedevecante vawas dues cama es corned ae eaeeeetecaake arsed amendann tc tteesGans 30
RECORDING w titcccdesccccesstevcccetas dteusinased ceticauas soessuneeassdcaccesdedusioueasdinnsesvssewventisestesusevevey ces 30
Pe A mane En en ee Ce Sree 31
PLAYBACK viii ec dcsses oa cancels ride sce sieesSiecsatdeen adden cae siceuscececsl aves Qeveds Sete tena cctugettancacateseiesesniees) 31
VIDEO RECORDING i ctivcadctevces eiviacivewctaded ccawssrareds a swans tangs dledbadusteteecsadess acmace ioeansvesaverdeede ces 31
ed atthe chest tale N eg pa ca a tat tata teas ne onaad 32
DOLBY PRO LOGIC SURROUND AND DOLBY 3CH LOGIC... ceceecee ec eeeeeeeeseeeeteteeneeeenen 32
JAZZ, DANCE, CHURCH, HALL, THEATER — SFC (Sound Field Control) surround................55. 33
Daerah eran mer enna oot 33
HOW TO USE THE TONE CONTROL )...........ccccececcseec ere eeececeencneeeseeceteeeerseseesseeseeeeeteaeeseeeusy 33
HOW TO USE THE ACOUSTIC MEMORY ............cscccececscncesnesecseeececerseeseneeeaeeeaecosneeansaneneeens 34
HOW TO USE THE ENHANCER AND SPLIT SCREEN.............ccccecsecececceceenseceeneoessrassseenseseenes 34
HOW TO USE THE ENHANCER MEMORY .............cccscsceceseseeeccessececetensaseseseeeaeseseeeseseeeeeeeees 34
Aaah gdh tetas a see ea titel NR Soi cut nnaeatical 35
dpe baste escetacktea tet ee elitytlcced onsets Sire rt re 35
FRE rN an rere mmr Tee 36
Besa cea ta tae tics olathe acs ae Tae anes ee cae tte 38
HINTS FOR BETTER RECEPTION...........:csssecccseecessceeueceuseceessaueueecsseesseuecceeusecesessecuasegsesanens 47
TROUBLESHOOTING ae saceceveiscccatinncediveveccaDancdedeg sadcesiandenbaa lads veces sdivvdpessesdstateedacedaccacerteees 48
SPECIFICATIONS 'oseee soe abi cecesbaceeecteetece st habadautencnasiesavatsieeaventeedeas Mecaucvareeadndevarend derseaweeass 50
3
< ARB1332>

BEFORE OPERATING, ADJUST THE POSITION OF THESE SWITCHES
TWO VOLTAGE SELECTOR SWITCHES
Only muttivoltage models are provided with these switches. U.S.,
Canadian, European, U.K. and Australian models are not provided with
these switches.
Mains voltages in Saudi Arabia are 127 V and 220 V only. Never use
this model with 110 V setting in Saudi Arabia.
The line voltage selector switches are on the rear panel. Before your
model is shipped from the factory, these switches are set to the power
requirements of the destination. Check that they are set properly before
plugging the power cord into the household wail socket. If the voltage
is not properly set or if you move to an area where the voltage
requirements differ, adjust the selector switches as follows.
1. Use a medium-size screwdriver. .
2. First, insert a screwdriver in the groove of the voltage selector at
the right, and adjust so that the tip of the groove points to the voltage
value of your area:
3. Next, insert a screwdriver in the groove of the voltage selector at
the left and adjust until the voltage is the same as at the right.
TWO VOLTAGE SELECTORS
220V
v10v
ee 110V Ui
Sao 20V-127V
29N
Medium-size
screwdriver
n
5
5
4
rr
a
8
z
8
>
NOTE:
i CAUTION: TWO VOLTAGE SELECTORS
0"
CHANNEL STEP/FM DE-EMPHASIS SWITCH
(Not available on U.S. and Canadian models)
The unit has been factory-preset to the channel allocation and de-
emphasis value for the area in which it is to be sold. If these values are
set incorrectly, the frequency display may stop at the wrong frequency,
or sound may be distorted, resulting in an inability to reproduce reception
signals at their proper sound quality. For this reason, be sure to confirm
that the values are set correctly before first using the unit.
[100kHz/10kHz/75ys] position:
Set to this position for areas with an FM reception step of 100kHz, AM
10kHz, and de-emphasis 75ys.
{50kHz/9kHz/50xs] position:
Set to this position, for areas with an FM reception step of 50kHz, AM
9kHz, and de-emphasis 50uzs.
NOTE:
When unsure about the channel allocation and de-emphasis values for
your area, consult your dealer for correct information.
CHANNEL STEP
‘FM DE-EMPHASIS
SOkHz/50uS f {_100kHz/75zS ~a FM
9kHz
1OkHz —a AM
x
ie
ce
220V
240V
Both switches must be in the same switch
setting; otherwise, unit can be damaged.
FEATURES
¢ DOLBY PRO LOGIC SURROUND performed by a
Digital Signal Processor (DSP).
© DSP provides five Sound Field Control (SFC) simulated
surround settings.
® Multi-Room & Source
Using this unit in combination with the optional MR-100 Multi-Room
System Remote Control Sensor Unit lets you enjoy different sources
in different rooms at the same time.
© Enhancer, Split screen function
The built-in detail-type enhancer is beneficial when making copies of
VCR tapes. By using the split-screen function, you can simultaneously
view the enhanced and origina! (non-enhanced) images. In this way you
can select the optimum settings for enhancing the image.
® Input attenuator
Depending on the component or source, input level to this unit may be
too high, possibly resulting in a distorted sound during playback. For
this reason, there's a built-in attenuator to decrease the level, thereby
eliminating distortion.
4
<ARB1332>
¢ Auto source control function
This function lets you store your usual receiver settings in memory, and
cail them up simply by pressing the call up button. (Up to two patterns
can be memorized.)
© Confirm function (remote control operation)
This function indicates receiver settings in the display section st the
touch of a remote control button.
¢ Equipped with the JOG dial, designed for easier
operation.
* Digital Simulated Stereo System (DSSS)
© Audio/Video programmable remote control unit.

BLOCK DIAGRAM
ca
a
ae
=i,
be
Et
tt
TAPE 1REC@-0%0
VCR I RECQ-o
VCR 2REC
ENHANCER
and
TVG . SPLITSCREEN
© MONITOR |
© MONITOR 2
ACCESSORY ITEMS
a= (_)
FM T-type Antenna AM Loop Antenna Audio/Video programmable Alkaline dry cell battey x 2
remote control unit (size “AA” (LR6/AM-3 ))
DSSS (Digital Simulated Stereo System)
Special DSP circuitry gives you simulated stereo sound from monaural
sources.
This operates even when a monaural signal is input into both the left
and right channels, or only one of the channels. When a signal is input
into only one channel, the output level is lower than when the signal
is input into both the left and right channels.
You can also enjoy combining it with surround modes other than
THEATER, DOLBY PRO LOGIC SURROUND or DOLBY 3CH LOGIC.
5
<ARB1332>

SURROUND MODE
This unit is equipped with DOLBY PRO LOGIC SURROUND. There’s also
a DSP (Digital Signal Processor), with a choice of five SFC (Sound Field
Control) simulated surround settings.
e JAZZ:
This gives you the sound field of a jazz club.
¢ DANCE:
A “hot’’ high-energy sound, with extra reverb for greater ambience.
e CHURCH:
The sound field of a church, ideal for reproducing the rich sound of a
pipe organ.
¢ HALL:
You can enjoy a convincing hall sound.
e THEATER:
Use this when watching movie sources that have a stereo soundtrack
to enjoy the effect of being in a movie theater. It is also effective when
used with video software bearing the [J] mark.
(It can not be used simultaneously with DOLBY PRO LOGIC SURROUND
or DOLBY 3CH LOGIC.)
¢ DOLBY PRO LOGIC SURROUND
Choose this setting for movies and music {especially Video Discs and
video tapes bearing the oo DOLSY SURROUND mark) playback.
DOLBY PRO LOGIC SURROUND continuously detects the size and
direction of the dominant signal and cancels undesirable crosstalk,
thereby providing signal emphasis.
You can clearly perceive the directions and source of the music.
Real flow of sound also can be re-created naturally using this feature.
{t gives the feeling of being in an outstanding and expansive sound field.
When using DOLBY PRO LOGIC SURROUND, a delay time setting of
20 ms is commonly used. Use a different setting if you prefer.
¢ DOLBY 3 CH LOGIC
By adding the signal for the rear speakers to the signal for the front
speakers, the front three channels (front L, front R, and CENTER) provide
amuch wider, more spacious sound field than possible during ordinary
stereo playback.
DOLBY PRO LOGIC SURROUND is equipped with the following
3 positions for the CENTER MODE.
When using DOLBY 3 CH LOGIC, you can select NORMAL or WIDE.
When using center speaker:
¢ NORMAL
Low range frequencies, which have little effect on directionality and
positioning, are routed to the left and right front speakers. So you can
use relatively small size speakers as the center speakers.
e WIDE
{f you use large size center speaker, choose this setting. The full
frequency range of the center speakers, from low to high, is routed to
the center speaker.
When notusing a center speaker: DOLBY PRO LOGIC SURROUND
* PHANTOM
The signal which would have been sent to the center speaker is divided
equally between the left and right front speakers.
SURROUND SPEAKER INSTALLATION EXAMPLE
To get the best effect out of the surround system, place the speakers
as shown below.
An example for center speaker location
When using a center speaker
FRONT
LEFT RIGHT
SPEAKER CENTER SPEAKER SPEAKER
FRONT
Listening area
REAR
LEFT
SPEAKER
6
<ARB1332>
NOTE:
© To avoid interference with the picture on a nearby TV set, use
magneticaily shielded speaker systems. This is particularly important
for the center speaker since it is usually located closest to the TV.
® Position the left and right channel speakers at equal distances from
the TV set and approximately six feet from each other.
¢ Position the center speaker above, below, or behind the TV set. Sound
may not appear to coincide with the picture if you position it next to
the TV set.
© Rear speakers are best positioned slightly above ear level.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under one or more of the
following patents: U.S. numbers 3,632,886, 3,746,792 and
3,959,590; CANADA numbers 1,004,603 and 1,037,877.
“Dolby’’ and the double-D oad symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Manufacturé sous licence de Dolby Laboratories Licensing
Corporation. En outre, sous license d’un ou plusiers des brevets
suivants: numéros américains 3,632,886, 3,746,792 et
3,959,590; numéros canadiens 1,004,603 et 1,037,877. Le
terme ‘‘Dolby”’ et ile symbole Double-D oo sont des marques
dépsoées de Dolby Laboratories Licensing Corporation.
Note:
DOLBY PRO LOGIC SURROUND and DOLBY 3CH LOGIC wil not
operate correctly if the signal passes through a graphic equaizer.
When using DOLBY PRO LOGIC SURROUND or DOLBY 3CH LOGIC,
turn off the TAPE 2 switch or set the graphic equalizer for flat
response or to its ‘‘through’’ (defeat) (or off) setting, if it has one.

CONNECTION CHART
* Illustration shows U.S. and Canadian models.
Setting Up the AM Antenna
* Insert the claw on the bottom of the antenna into the groove in
the leg.
* Place the antenna on a level surface and rotate it to locate the
orientation that yields the best reception.
¢ Use the attachment hole in the leg to screw to wail or other
location, then insert the claw on the bottom of the antenna into
the groove in the leg (fixing the antenna in the direction that gives
the best reception).
Lead wire
CONNECTING THE POWER CORD
(For U.S. and Canadian models)
Household electrical outlets are provided with specific polarity, a
live side and a neutral (ground) side. This unit utilizes such polarity
in order to improve sound quality. As shown in the illustration, be
sure to insert the power piug so that its blades match the width of
slots in the outlet.
AC wall socket
Long slot is neutral
(ground) side.
Insert the wide blade
into the ground side slot.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the piug by tugging
the cord and never touch the power cord when your hands are wet as
this could cause a short circuit or electric shock. Do not place the unit,
apiece of furniture, etc., on the power cord, or pinch the cord. Never
make a knot in the cord or tie it with other cords. The power cords
should be routed such that they are not likely to be stepped on. A
damaged power cord can cause fire or give you an electrical shock.
Check the power cord once in a while. When you find it damaged, ask
your nearest PIONEER authorized service center or your dealer for a
replacement.
Precaution regarding installation position of cassette deck.
If the cassette deck is installed in the @) positions shown in the
drawing below, it may be adversely affected during playback. If
possible, it’s better to install it in the (8) position.
THE S-VIDEO CONNECTORS
When using a VCR 1, VCR 2, VCR 3, LD and TV monitor which
has S-VIDEO connectors, they can be connected to the S-VIDEO
connectors.
For the operation of components connected to S-VIDEO connectors,
refer to the instruction manuals of the corresponding components.
NOTE:
® In this unit, the S-VIDEO connectors (Y-C separate) and the regular
pin jacks are independent, so any signal input through a pin jack
must be output from the pin jack, and any signal input through
an S-VIDEO connector must be output through the S-VIDEO
connector.
© The S-VIDEO connector is for video portion only, so be sure to
make audio connections also.
How to use S-VIDEO connectors
uN
O 9) S-VIDEO jack
=
Check the position of
the holes and insert.
‘
S-VIDEO plug
For the method of switching the TV monitor S-VIDEOQ connector/
VIDEO jack, refer to the TV monitor's instruction man ual.
7
<= ARB1332 >

CONNECTION CHART
Basic Audio Component Connections
* FM, AM antenna connection
¢ Turntable
© First cassette deck
* Compact disc player
Accessory FM T-type antenna Cassette deck
Pe
Stretch the antenna out
: a REC PLAY
to its full ““T’’ shape, and
affix to a wall, etc.
cle
4
AC wall socket
To AC OUTLETS
To AC OUTLETS
Turntable
CD
player
8
<ARB1332>

CONNECTION CHART
Basic Video Component Connections (1)
* First VCR
VHF antenna UHF antenna
VIDEO
OUT
* “ai A
a8 68
(2)
x* S (video) connection See page 7.
9
¢ ARB1332>

CONNECTION CHART
Basic Video Component Connections (2)
® LaserDisc Player (Compatible LaserDisc player)
e TV tuner
¢ First TV monitor
* S (video) connection. See page 7.
AUDIO «viDEo)6=« GS
OUT OUT OUT
LD Player
(CD CDV LD player)
2 i
zi,
@©)OOQOOOOS©)
\)©OO®
©
QO)
vai
a 2H
a
‘@OOQOOOO
7?
AY
bi
S VIDEO
IN IN
TV tuner, etc First TV monitor
10 :
<ARB1332>

CONNECTION CHART
Additional Audio Components NOTE:
© Dolby Surround will not operate correctly if the signal passes through
* Second cassette deck (Graphic equalizer) @ graphic equalizer.
* Audio equipment (Second CD player, etc.) When using Dolby Surround, turn off the TAPE 2 MONITOR button
or set the graphic equalizer for flat response or to its through (defeat)
setting.
© Sound from TAPE 2 cannot be recorded on VCR 1, 2, or TAPE 7.
Used with a second
cassette deck.
| TIE DEE EES Used with a graphic equalizer \ atateteietebateebatatatatatatanaeteataanaeteta "
5 — and second cassette deck. '
soo
-
Used with a graphic equalizer.
‘
'
‘
t
t
i]
1
1
1
I
I
Graphic ‘
!
'
'
1
'
'
t
'
'
/
[REC] we equalizer
REC
(IN)
iRec|
PLAY
(OUT)
OUT
ToL and R ToLandR ToLandR To Land R
REC jacks PLAY jacks REC jacks PLAY jacks
ne a ee i ee ee a eee ee
®— O— O-— 6:
60 Ge
68,68
Audio equipment
(Playback only)
11
<= ARB1332>

CONNECTION CHART
Additional Video Components
*® Second VCR
© Video equipment
(Second LD player, etc.)
© Second TV monitor
%* S (video) connection.
Second VCR See page 7.
Front panel
Video equipment Second TV monitor VCR (for playback only), or
(Second LD player, etc.) another component such as
a TV camera.
12
<ARB1332>

CONNECTION CHART
When used with another amplifier (power amplifier,
preamplifier)
[FRONT]
{a}
When using the preamplifier of the receiver and using a separate stereo
power amplifier to increase power.
(b)
When using the power amplifier of the receiver and using a separate
stereo preamplifier.
Caution for use of AC OUTLETS:
Components which have electrical power consumption greater than that
indicated on the rear panel of this unit cannot be connected. Please take
necessary precaution.
fon ro nn +
{
!
'
i
{
4
Remove both
connector bars.
Keep the removed
bars for future use.
When using PRE AMP OUT jack:
Use these jacks when using a separate amplifier as the power source
instead of this unit, and listening t to speakers which are connected to
the separate amplifier.
NOTE:
Sound from the speaker channels (front, center, rear), from which the
connector bars have been removed in order to make a connection,
cannot be heard if the speakers are connected to the unit.
When using POWER AMP IN jacks:
Use these jacks when this unit is being used as the power amplifier for
the surround channels (front, center, rear).
With separate surround processing components, each corresponding
channel (front, center, rear) which has a sound output should be
connected correspondingly.
NOTE:
When the connector bars are removed to make connections, sound from
all channels of separate components connected to this unit’s input
terminals, as well as broadcasts received by the unit, cannot be heard
via speakers connected to the unit.
To AC OUTLETS
(SWITCHED)
(b)
op ae Ee ee ee ol
Stereo preamplifier
proc noche --- ------ - -- -- + --- ------------
13
<ARB1332>

CONNECTION CHART
[REAR and CENTER]
(a) {b)
When using the preamplifier of the receiver and using a separate stereo When using the power amplifier of the receiver and using a separate
power amplifier to increase power. stereo preamplifier.
(a) {b)
a ee ee laa rr
SUB WOOFER (Center) 7
CENTER
Built-in amplifier woofer,
monaural amplifier, etc.
en
Speaker
Preamplifier
=
i}
(
I
i}
1 i}
i t
| |
t
| l
' 1
| oo 00} |
i}
1 1
|
|
H J
i
Power amplifier
PRE
OUT
CNG)
60 @@
CIeNele
To AC OUTLETS
(SWITCHED)
Remove both
connector bars.
Keep the removed
bars for future use.
14
<ARB1332>

CONNECTION CHART
Speakers Connection (1)
* Front L, R speakers
* Front center speaker
* Rear L, R speakers
Twist
wire
tip.
S
bp
ip
@
Loosen
cap
When
connecting
speakers
to
the
FRONT
SPEAKERS
ie
a
Li
tyre
B terminals, the procedure is the same as that used 10 mm = ; @ Staion ap:
for connecting speakers to the FRONT SPEAKERS A (3/8 in} @) Press lever. >
terminals.
@
Insert
wire.
®
@) Release lever.
For details concerning speakers impedance.
NOTE:
Do not allow any of the cord’s conductors to protrude
from the terminals or touch any other conductors.
Malfunctioning or breakdowns may occur when
conductors come into contact with each other.
Front speaker impedance
Set the IMPEDANCE SELECTOR switch to -o—O—@
ah bath Got Gah
the nominal impedance of your speakers. . @, @)@
Ly
{ Vo.
iE A ORB; 40 TO LESS
tow THAN 82
AANDB; 8 2TO 162
NOTE:
«lf you have one pair of speakers only,
connect it to front speaker terminals A
or B.
* Position HIGH: when using one pair of
speakers of 8 2 to 76 2.
* Position LOW: when using one pair of
speakers {4 2 to 8 Q} or two pairs of
speakers (8 Qto 16 2 for each speaker).
Center speaker impedance
Connect center speaker system with a ;
nominal
impedance
of
8
0.
CENTER
Rear speaker impedance
Connect rear speaker systems with a
nominal impedance of between 8 and
16.9.
NOTE:
Be sure to observe speaker polarity.
15
<ARB1332>

CONNECTION CHART
Connecting Multi-Room and Source
¢ TV Monitor
Speakers
© Multi-Room remote control sensor unit MR-100 (option)
MAIN ROOM
16
<ARB1332>
VIDEO IN

CONNECTION CHART
NOTE:
¢ Be careful not to make the wrong connections for CONTROL IN/OUT
(black) and MULTI-ROOM REMOTE IN (green).
¢ if you connect to the CONTROL jacks of other components, such as
a CD player or cassette deck, bearing the mark, you can also
enjoy remote control of these components from room B. (For details
concerning connections, refer to page 24.)
SUB ROOM
AC wall
socket
17
<ARB1332 >

CONNECTION CHART
Application example- MULTI-AMPLIFIER SYSTEM
Crossover Network
High range
Low
range
Power
Amplifier
PREAMP POWER AMP
OUT IN
1
Receiver
I
PREAMP POWER AMP
Speaker system
18
<ARB1332>

FRONT PANEL FACILITIES
® © @ ®®OD ®@OO® ®
®@®D OB@OHVBOOD@®®H © ®
@)POWER STANDBY/ON switch/indicator
This is the switch for electric power.
ON ...cceee sees When set to the ON position, power is supplied and the
unit becomes operational.
STANDBY .. When set to STANDBY position, the main power flow is
cut and the unit is no jonger fully operational. A minute
flow of power feeds the unit to maintain operation
readiness.
The STANDBY indicator lights when the power is STANDBY, and goes
out during ON.
(@ MULTI ROOM & SOURCE button (See page 36)
Use in combination with the separately sold MR-100 Multi-Room remote
control unit.
When this button is on, the source selected with the INPUT SELECTOR
atthat time is set to the Sub room function. The selected sub-function’s
sound is output through SUB ROOM SPEAKERS, and the video signal
is output through the MULTI-ROOM & SOURCE VIDEO OUT jack. If
you install speaker systems connected to the MULTI-ROOM SPEAKERS
terminals in a different room, you can enjoy different sources in two
different rooms with a single main unit.
@ AUTO SOURCE CONTROL, MEMORY buttons
(See page 35)
AUTO SOURCE CONTROL 1, 2:
These buttons are for memorizing and recalling your current settings.
Both 1 and 2 can be used to memorize settings. If you connect another
component, such as a CD player, to the CONTROL OUT jack on the
rear panel, the signals to switch power on and start play are also
transmitted.
MEMORY:
Use when memorizing settings to an AUTO SOURCE CONTROL button.
@ Display section (see page 22)
@STATION CALL (RANDOM 30 CH) buttons
¢ These buttons are used to preset and recall desired broadcasting
stations. You can also preset AUTO/MONO button settings.
®@ @® ® ® @
Station call operation example:
If you press the [*2] button:
® Once — station 2 is selected.
® Twice — station 12 is selected.
© Three times — station 22 is selected.
NOTE:
Pressing the STATION CALL buttons when a comporerrt other than
TUNER is selected causes the INPUT SELECTOR setting to switch to
TUNER.
© They are also used when performing direct access tuning.
@ SURROUND MODE buttons (See pages 6, 32)
@ JOG MODE indicators
The indicator for the mode that can currently be operated by the JOG
dial fights. If it is not the mode you want to operate, switc) to the desired
mode with the JOG MODE button (@).
Remote sensor window
@ INPUT ATT button
Use this when there is distortion due to excessively hih input signal
level. When this is switched ON, — 10 dB attenuator oprastes, and the
INPUT ATT indicator in the display section lights.
ACOUSTIC/ENHANCER MEMORY, SELECT buttons
ACOUSTIC/ENHANCER MEMORY:
Use to operate acoustic memory and enhancer memory. See page 34.
ACOUSTIC SELECT:
Use this to store desired sound quality settings in menosy. Also use
it to recall memorized sound quality settings from memry.. For further
details concerning memory operation, refer to page 34,
ENHANCER SELECT:
Use this to store a desired enhancer effect in memory, red to recall a
desired enhancer effect. For further details concenisig memory
operation, refer to page 34.
When the enhancer has been memorized, then the eria ncer will be
automatically switched ON when this button is presse,
19
< ARB1332>

FRONT PANEL FACILITIES
@ RETURN button
Pressing this button returns the receiver to the following settings, the
sound level being controlled by MASTER VOLUME control knob.
© TAPE 2 MONITOR OFF
e SURROUND MODE OFF
e SPEAKERS A ON
e MUTING OFF
e BALANCE CENTER
e INPUT SELECTOR TUNER
¢ STATION CALL 1 CH*
* When a station is not memorized in 1 CH, station search will
automatically proceed from the frequency displayed.
@ DIRECT button
Press this to listen to source sound without passing the audio signal
through sound quality and balance adjusting circuitry.
The surround mode, and rear and center speakers are automatically
switched off.
@3 MASTER VOLUME control
Use to adjust the sound volume from the front, center and rear speakers.
When you adjust volume by remote control, the indicator on the knob
flashes.
When the MULTI ROOM & SOURCE switch is ON, volume level in sub
room cannot be adjusted with this knob. To adjust sub room volume,
point the remote control at the MR-100 in the sub room and operate.
DSSS (Digital Simulated Stereo System) button
Operate this when inputting a monaural signal to enjoy a simulated
stereo sound. You can use it when a monaural signal is input into both
the left and right channels or when a monaural signal is input into only
one of the channels.
@® JOG dial
This lets you control the following five functions.
(1} Tuner frequency (manual tuning).
(2) Selection of tetters for station naming.
(3) Video enhancer effect level adjustment.
(4) Surround’s delay time selection.
(5) Surround’s total effect level adjustment.
You can select which function you want to control with the JOG MODE
button @®), but the mode automatically switches when a function
changes. For example, if you press the STATION NAME button, the
JOG MODE automatically switches to the CHARACTER mode.
MUTING button
Press to temporarily cut off the sound volume. When pressed again,
the sound will return to its previous level.
@ SPLIT SCREEN OFF/ON button
If you turn the ENHANCER OFF/ON button ON to add the video
enhancer effect, and then turn this button on, the right side of the picture
will have the enhancer effect added, and the left side will be without
the enhancer effect. The signal that has passed through the enhancer
is output through the TO MONITOR TV jacks and VCR OUT jacks.
A split screen picture is output from the TO MONITOR TV jacks.
However, S$ jack output is not affected by enhancer or split screen.
SPEAKERS A, B buttons
These are ON/OFF buttons for the speaker systems. When switched
ON, SPEAKERS indicators (A, B) in the display section light.
PHONES jack
Connect the plug on your headphones to this jack. To hear only through
the headphones, set all SPEAKERS A’and B buttons to the OFF position.
NOTE:
There are no ON/OFF switches for the rear and center speakers, so when
you want to listen only on headphones, switch surround OFF. If you
want to listen with surround ON, reduce rear and center volume levels
using the remote control.
20
<ARB1332>
BAND button (FM/AM)
Use this to switch between FM and AM frequency band reception.
@) AUTO TUNING buttons (Down (-), Up (+))
+: Performs tuning in ascending frequency order.
—: Performs tuning in descending frequency order.
@ CUSTOM MEMORY SELECT button (See page 27)
Recall a genre name with this button.
@ SCAN button (See page 27)
Operates when the INPUT SELECTOR is set to TUNER. Station
frequencies assigned to the STATION CALL buttons are tuned in, one
after another, beginning with the current station no., for approximately
5 seconds each. Press the button again and reception of the station
presently being received will continue. Station frequencies not assigned
station numbers in the memory are skipped.
When you have selected a CUSTOM MEMORY genre, memory scan
is performed on the stations in that genre.
MEMORY button
Pressing this button will result in the memorization of the current
broadcast band, reception frequency, and FM AUTO/MONO mode (see
page 27).
This button is also used to input station names (see page 28), and
custom memory operation (see page 27).
@ STATION NAME button
This button is used when inputting station names. (See page 28.)
@) AUTO/MONO button
Use to select the auto stereo mode or monaural mode when listening
to FM broadcasts. The monaural mode has been selected when the FM
MONO indicator in the display section is lit.
Auto stereo mode:
Normally, leave in this mode for reception. When a stereo broadcast
is received, it will be automatically reproduced in stereo.
During stereo broadcast reception, the STEREO indicator in the display
section lights.
Monaural mode:
When receiving distant stations or stations with weak broadcast signals,
the input signal may be weak, thus resulting in increased noise during
FM stereo broadcasts. in this event, setting the receiver to the monaural
mode will reduce the noise; however, FM stereo broadcasts will be
reproduced in monaural sound.
NOTE:
This button has no effect on reception of AM broadcasts.
@ DIRECT ACCESS button (See page 26)
When this button is pressed, the STATION CALL buttons function as
10-key number buttons for direct input of the desired reception
frequency.
When frequencies that cannot be received are entered, the entered
frequency value flashes, before reception of the previous frequency
resumes.
HITS (Hyper Intelligent Tuning System) button
(See page 29)
¢ If the HITS button is pressed at the currently displayed station
frequency, the receiver searches up and down the frequency for the
next station and stops at the first one it finds.
¢ If the HITS button is pressed during STATION NAME input (see
page 28), the receiver performs a memory search in order of ascerading
station number for memorized stations whose names begin with the
same letter as the station just input.
¢ If the HITS button is pressed during input of numbers for DIRECT
ACCESS tuning, the receiver sets the remaining digits, whichinave
not yet been input, to “‘0’, searches for the corresposding
frequencies, and stops on the first station it finds.