Pioneer AVH-P6300BT/XNUC User manual

ORDER NO.
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2011
AVH-P6300BT/XNUC CRT4684
DVD AV RECEIVER
AVH-P6300BT /XNUC
AVH-P6350BT/XNRD
AVH-P6350BT/XNRI
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3268 CRT4534 MS7 DVD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
For details, refer to "Important Check Points for Good Servicing".
K-ZZZ JAN. 2011 Printed in Japan

AVH-P6300BT/XNUC
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
CAUTION:
USE OF CONTROLS ORADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHERTHANTHOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
-Safety Precautions for those who Service this Unit.
When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
60825-1:2007, and contains a class 1M laser
module. To ensure continued safety, do not re-
move any covers or attempt to gain access to
the inside of the product. Refer all servicing to
qualified personnel.
CAUTION—CLASS 1M INVISIBLE LASER
RADIATION WHEN OPEN, DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65

AVH-P6300BT/XNUC 3
5678
5678
C
D
F
A
B
E
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.
Additional Laser Caution
Transistors Q1103 and Q1104 in PCB drive the laser diodes for DVD and CD
respectively. When Q1103 or Q1104 is shorted between their terminals,
the laser diodes for DVD or CD will radiate beam. If the top cover is removed
with no disc loaded while such short-circuit is continued, the naked eyes may
be exposed to the laser beam.
Laser diode characteristics
Wave length:
DVD:660 nm to 670 nm
CD:780 nm to 800 nm
Focus lens on Maximum output:
CD:6.26 mW(Emitting period :9 sec.)
DVD:1.27 mW (Emitting period : unlimited)

AVH-P6300BT/XNUC
4
1234
1234
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
aSafe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

AVH-P6300BT/XNUC 5
5678
5678
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION .....................................................................................................................................2
1. SERVICE PRECAUTIONS................................................................................................................................6
1.1 SERVICE PRECAUTIONS.........................................................................................................................6
1.2 NOTES ON SOLDERING...........................................................................................................................7
2. SPECIFICATIONS.............................................................................................................................................8
2.1 SPECIFICATIONS......................................................................................................................................8
2.2 DISC/CONTENT FORMAT.......................................................................................................................10
2.3 PANEL FACILITIES..................................................................................................................................10
2.4 CONNECTION DIAGRAM........................................................................................................................13
3. BASIC ITEMS FOR SERVICE........................................................................................................................20
3.1 CHECK POINTS AFTER SERVICING.....................................................................................................20
3.2 PCB LOCATIONS.....................................................................................................................................21
3.3 JIGS LIST.................................................................................................................................................22
3.4 CLEANING ...............................................................................................................................................23
4. BLOCK DIAGRAM..........................................................................................................................................24
4.1 OVERALL CONNECTION DIAGRAM......................................................................................................24
4.2 BLOCK DIAGRAM....................................................................................................................................26
5. DIAGNOSIS....................................................................................................................................................36
5.1 OPERATIONAL FLOWCHART.................................................................................................................36
5.2 INSPECTION METHOD OF PICKUP UNIT .............................................................................................37
5.3 DIAGNOSIS FLOWCHART......................................................................................................................40
5.4 ERROR CODE LIST.................................................................................................................................58
5.5 CONNECTOR FUNCTION DESCRIPTION .............................................................................................61
5.6 MECHANICAL DESCRIPTION.................................................................................................................62
6. SERVICE MODE.............................................................................................................................................66
6.1 DVD TEST MODE....................................................................................................................................66
6.2 MONITOR TEST MODE...........................................................................................................................77
7. DISASSEMBLY...............................................................................................................................................87
8. EACH SETTING AND ADJUSTMENT..........................................................................................................101
8.1 DVD ADJUSTMENT...............................................................................................................................101
8.2 MOTHER PCB ADJUSTMENT...............................................................................................................106
8.3 MONITOR PCB, MONITOR UNIT ADJUSTMENT.................................................................................108
9. EXPLODED VIEWS AND PARTS LIST........................................................................................................110
9.1 PACKING................................................................................................................................................110
9.2 EXTERIOR (1)........................................................................................................................................112
9.3 EXTERIOR (2)........................................................................................................................................114
9.4 EXTERIOR (3)........................................................................................................................................116
9.5 EXTERIOR (4)........................................................................................................................................118
9.6 DVD MECHANISM MODULE.................................................................................................................122
10. SCHEMATIC DIAGRAM..............................................................................................................................124
10.1 MOTHER PCB (ANALOG PART).........................................................................................................124
10.2 MOTHER PCB (SYSTEM PART)(GUIDE PAGE).................................................................................126
10.3 MOTHER PCB (POWER SUPPLY PART)............................................................................................132
10.4 MOTHER PCB (MMD PART)(GUIDE PAGE).......................................................................................134
10.5 MOTHER PCB (I/F PART)(GUIDE PAGE) ...........................................................................................140
10.6 TUNER PCB.........................................................................................................................................146
10.7 DVD CORE UNIT (MS7)(GUIDE PAGE)..............................................................................................148
10.8 COMPOUND UNIT(A) and COMPOUND UNIT(B)...............................................................................154
10.9 PANEL PCB..........................................................................................................................................156
10.10 KEYBOARD PCB...............................................................................................................................158
10.11 MAIN PCB UNIT, SWITCH PCB UNIT and VOLUME PCB UNIT.......................................................160
10.12 MONITOR PCB (MONITOR PART)(GUIDE PAGE) ...........................................................................162
10.13 MONITOR PCB (BACKLIGHT PART) ................................................................................................168
10.14 BT PCB and BT ANT PCB..................................................................................................................170
10.15 WAVEFORMS.....................................................................................................................................171
11. PCB CONNECTION DIAGRAM..................................................................................................................174
11.1 MOTHER PCB......................................................................................................................................174
11.2 TUNER PCB .........................................................................................................................................178
11.3 DVD CORE UNIT(MS7)........................................................................................................................180
11.4 COMPOUND UNIT(A) and COMPOUND UNIT(B)...............................................................................184
11.5 PANEL PCB..........................................................................................................................................185
11.6 KEYBOARD PCB..................................................................................................................................186
11.7 MAIN PCB UNIT, SWITCH PCB UNIT and VOLUME PCB UNIT.........................................................187
11.8 MONITOR PCB.....................................................................................................................................188
11.9 BT PCB.................................................................................................................................................192
11.10 BT ANT PCB.......................................................................................................................................193
12. ELECTRICAL PARTS LIST.........................................................................................................................194

AVH-P6300BT/XNUC
6
1234
1234
C
D
F
A
B
E
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
3. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during
power-on mode may damage the ICs inside the unit.
4. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY" .
5. After replacing the pickup unit, be sure to skew adjustment.
6. When a flash ROM needs to be replaced by service, do not replace an IC but a core unit (as no encryption key is
written in a flash alone).
7. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector
is plugged or unplugged.
8. Countermeasures to user complaints on iPhone/iPod touch lip synchronization
When a video is replayed, the video and audio may be out of synchronization depending on the connected
iPod or iPhone.
If it is annoying, perform the following operation.
However, this operation will slightly deteriorate the sound quality of the iPod source.
Also, it will disable the ASR function when the iPod source is used.
[Default]
Audio digital mode
[Switching procedure]
Press MODE and EJECT and turn on Accessory simultaneously
The above switches the “Audio digital mode” to the “Audio analog mode”.
When the mode is switching, the BEEP1 sound will be heard.
[Supplement]
• The mode switching operation can only switch the “Audio digital mode” to the “Audio analog mode”.
(The BEEP1 sound will be heard every time.)
• No indication of the mode is provided.
[Resetting the mode]
Reset or BackUP OFF
The above resets the mode to the “Audio digital mode”.
Verification method
If the voice is not heard when a movie is played with the AUX jack unplugged, the voice has been switched to analog.
* Initially, AUDIO sound is output with the AUX jack unplugged as it comes in via USB (digital).
9. Recautions for AEQ measurement
If the microphone is not connected securely, the microphone input signals may become inaccurate and an
error message “Plug the supplied microphone securely into the jack” may appear due to the measurement failure.
10. EJECT LOCK MODE for DVD mechanism
How to enter : Press RESET while pressing [FORWARD] and [EJECT] keys together.
How to exit : Same procedure to enter this mode.
11. When EEPROM is initialized, eject lock may be enabled. Please cancel eject lock in this case.
12. The connector in the monitor unit CN5002:CKS6008 is the connector with both contacts.
If the flexible board is inserted reversely, unintended connection is made and it may cause a breaking of fuse or
destruction of part.
Do not insert it reversely.
Monitor Unit IC5701 TK61222CQ6 Heat pad
13. The part listed below is difficult to replace as a discrete component part.
When the part listed in the table is defective, replace whole Assy.

AVH-P6300BT/XNUC 7
5678
5678
C
D
F
A
B
E
1.2 NOTES ON SOLDERING
14. area and a heat sink becomes hot areas. Be careful not to burn yourself.
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

AVH-P6300BT/XNUC
8
1234
1234
C
D
F
A
B
E
2. SPECIFICATIONS
2.1 SPECIFICATIONS
General
Power source.............................14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system...................Negative type
Maximum current consumption
...................................................10.0 A
Dimensions (W × H × D):
DChassis.....................178 mm × 50 mm ×
165mm
(7in. × 2in. × 6-1/2in.)
Nose...........................170 mm × 46 mm × 27 mm
(6-3/4in.×1-3/4in.×1in.)
Weight ........................................ 2.2 kg (4.84 lbs)
Display
Screen size/aspect ratio.......7.0 inch wide/16:9
(effective display area:
154.0mm×86.9mm)
Pixels........................................... 345 600 (1 440 × 240)
Display method ....................... TFT active matrix, driving
type
Color system.............................NTSC
Durable temperature range (power off)
...................................................–20 °C to +80 °C
Angle adjustment ................... 50° to 110°
(initial settings: 90°)
Audio
Maximum power output .......50 W × 4
70 W × 1/2 Ω (for subwoo-
fer)
Continuous power output ...22 W × 4 (1 kHz, 5% THD, 4
Ω load, both channels dri-
ven)
Load impedance..................... 4 Ω (4 Ω to 8 Ω (2 Ω for 1ch)
allowable)
Preout maximum output level
...................................................4.0 V
Equalizer (8-Band Graphic Equalizer):
Frequency.........................40 Hz/80Hz/200Hz/400Hz/
1kHz/2.5kHz/8kHz/10kHz
Gain.................................... ±12 dB
HPF:Frequency.........................50 Hz/63Hz/80Hz/100Hz/
125Hz
Slope...................................–12 dB/oct
Subwoofer (mono):
Frequency.........................50 Hz/63Hz/80Hz/100Hz/
125Hz
Slope...................................–18 dB/oct
Gain.....................................+6 dB to –24 dB
Phase .................................Normal/Reverse
Bass boost:
Gain.....................................+12 dB to 0 dB
DVD Player
System........................................ DVD video, Video CD, CD,
WMA, MP3, AAC, DivX,
JPEG system
Usable discs .............................DVD video, Video CD, CD,
CD-R/RW, DVD-R/RW/RDL
Region number ........................1
Frequency response...............5 Hz to 44 000 Hz (with DVD,
at sampling frequency
96kHz)
Signal-to-noise ratio...............96 dB (1 kHz) (IHF-A net-
work) (RCA level)
Output level:
Video...................................1.0 Vp-p/75 Ω (±0.2 V)
Number of channels ............. 2 (stereo)
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only) (.m4a)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
USB
USB standard specification
...................................................USB 1.1, USB 2.0 full speed
Maximum current supply ....500mA
USB Class..................................MSC (Mass Storage Class)
File system.................................FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
SD
Compatible physical format
...................................................Version 1.1
File system.................................FAT12, FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
FM tuner
Frequency range..................... 87.9 MHz to 107.9 MHz
Usable sensitivity.................... 9 dBf (0.8 µV/75 Ω, mono,
S/N: 30dB)
Signal-to-noise ratio...............72 dB (IHF-A network)
AM tuner
Frequency range..................... 530 kHz to 1 710 kHz
(10kHz)
Usable sensitivity.................... 25 µV (S/N: 20dB)
Signal-to-noise ratio...............62 dB (IHF-A network)
Bluetooth
Version.........................................Bluetooth 2.0 certified
Output power ............................+4 dBm Maximum
(Power class 2)
CEA2006 Specifications
Power output .............................14 W RMS × 4 Channels
(4 Ω and 1 % THD+N)
S/N ratio......................................91 dBA (reference: 1 W into
4 Ω)
Note
Specifications and the design are subject to mod-
ifications without notice.
• AVH-P6300BT/XNUC
Backup current ........................ 5.0 mA or less
<
=

AVH-P6300BT/XNUC 9
5678
5678
C
D
F
A
B
E
General
Rated power source...............14.4 V DC
(allowable voltage range:
12.0V to 14.4V DC)
Grounding system.................. Negative type
Maximum current consumption
...................................................10.0 A
Dimensions (W × H × D):
DChassis.....................178 mm × 50 mm ×
165mm
Nose...........................170 mm × 46 mm × 27 mm
Weight ........................................ 2.2 kg
Display
Screen size/aspect ratio.......7.0 inch wide/16:9
(effective display area:
154.0mm × 86.9 mm)
Pixels........................................... 345 600 (1 440 × 240)
Display method ....................... TFT active matrix, driving
type
Color system.............................NTSC/PAL/PAL-M/SECAM
compatible
Durable temperature range (power off)
...................................................–20 °C to +80 °C
Audio
Maximum power output .......50 W × 4
70 W × 1/2 Ω (for subwoo-
fer)
Continuous power output ...22 W × 4 (1 kHz, 5% THD, 4
Ω load, both channels dri-
ven)
Load impedance..................... 4 Ω (4 Ω to 8 Ω (2 Ω for 1ch)
allowable)
Preout maximum output level
.................................................. 4.0 V
Equalizer (8-Band Graphic Equalizer):
Frequency........................ 40 Hz/80Hz/200Hz/400Hz/
1kHz/2.5kHz/8kHz/10kHz
Gain.................................... ±12 dB
HPF:Frequency........................ 50 Hz/63Hz/80Hz/100Hz/
125Hz
Slope.................................. –12 dB/oct
Subwoofer (mono):
Frequency.........................50 Hz/63Hz/80Hz/100Hz/
125Hz
Slope.................................. –18 dB/oct
Gain.................................... +6 dB to –24 dB
Phase ................................ Normal/Reverse
Bass boost:
Gain.................................... +12 dB to 0 dB
DVD Player
System........................................ DVD video, Video CD, CD,
WMA, MP3, AAC, DivX,
JPEG system
Usable discs .............................DVD video, Video CD, CD,
CD-R/RW, DVD-R/RW/RDL
Region number .......................4
for South American and Oceanian models
Region number .......................2
for Middle East Asian and South African models
Frequency response...............5 Hz to 44 000 Hz (with DVD,
at sampling frequency
96kHz)
Signal-to-noise ratio...............96 dB (1 kHz) (IEC-A net-
work) (RCA level)
Output level:
Video...................................1.0 Vp-p/75 Ω (±0.2 V)
Number of channels ............. 2 (stereo)
MP3 decoding format .......... MPEG-1 & 2 Audio Layer 3
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only) (.m4a)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
USB
USB standard specification
...................................................USB 1.1, USB 2.0 full speed
Maximum current supply ....500mA
USB Class..................................MSC (Mass Storage Class)
File system.................................FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
SD
Compatible physical format
...................................................Version 1.10
File system.................................FAT12, FAT16, FAT32
MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
Backup current ........................ 5.0 mA or less
WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
(2ch audio)
(Windows Media Player)
AAC decoding format............MPEG-4 AAC (iTunes en-
coded only)
(Ver. 9.0.3 and earlier)
DivX decoding format............Home Theater Ver. 3, 4, 5.2,
6 (.avi, .divx)
FM tuner
Frequency range..................... 87.5 MHz to 108.0MHz
Usable sensitivity.................... 9 dBf (0.8 µV/75 Ω, mono,
S/N: 30dB)
Signal-to-noise ratio...............72 dB (IEC-A network)
AM tuner
Frequency range..................... 531 kHz to 1 602 kHz (9 kHz)
530kHz to 1640kHz
(10kHz)
Usable sensitivity.................... 25 µV (S/N: 20dB)
Signal-to-noise ratio...............62 dB (IEC-A network)
Bluetooth
Version........................................ Bluetooth 2.0 certified
Output power ...........................+4 dBm Maximum
(Power class 2)
Infrared remote control
Wavelength................................945 nm
Output ......................................... typ; 10 mw/sr per Infrared
LED
Note
Specifications and the design are subject to mod-
ifications without notice.
• AVH-P6350BT/XNRD, XNRI

AVH-P6300BT/XNUC
10
1234
1234
C
D
F
A
B
E
2.2 DISC/CONTENT FORMAT
2.3 PANEL FACILITIES
(UC model)
(UC model)
(UC model)
(RD, RI models))
Head unit
PartPart
1Volume/ MUTE/8OPEN/CLOSE
2
MENU
Displaying the
menu.
Returning to the
normal display.
9
AUX input jack
(3.5mm stereo/
video jack)
Use to connect an
auxiliary device.
3MODE Turning the infor-
mation display off. a
Auto EQ micro-
phone input jack
Use to connect an
auto EQ micro-
phone.
4Disc loading slot b
USB port
When connecting,
open the USB con-
nector lid.
5SRC/OFF cRESET
6/(TRACK/
SEEK)dSD memory card
slot
7(eject)
CAUTION
Use an optional Pioneer USB cable (CD-U50E)
to connect the USB audio player/USB mem-
ory as any device connected directly to the
unit will protrude out from the unit and may
be dangerous.
Do not use unauthorized products.
Notes
Insert it with the contact surface facing down,
and press on the card until it clicks and com-
pletely locks into place.
When the navigation system is connected,
press MODE to switch to the navigation dis-
play. Press MODE and hold to turn the display
off.
Press MODE again to turn the display on.
Press and hold MENU to display
Picture Adjustment.
Refer to Changing the picture adjustment.
For detailson how to operate a navigation sys-
tem from this unit, refer to its operation man-
ual.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
UC : BPZ20P060FTC
• AVH-P6300BT/XNUC

AVH-P6300BT/XNUC 11
5678
5678
C
D
F
A
B
E
Head unit
PartPart
1Volume/MUTE/7(eject)
2
MENU
Displaying the
menu.
Returning to the
normal display.
8OPEN/CLOSE
3MODE Turning the infor-
mation display off. 9
AUX input jack
(3.5mm stereo/
video jack)
Use to connect
an auxiliary de-
vice.
Auto EQ micro-
phone input
jack
Use to connect
an auto EQ mi-
crophone.
4Disc loading slot a
USB port
When connecting,
open the USB con-
nector lid.
traPtraP
5SRC/OFF bRESET
6/(TRACK/
SEEK)cSD memory card
slot
CAUTION
Use an optional Pioneer USB cable (CD-U50E)
to connect the USB audio player/USB mem-
ory as any device connected directly to the
unit will protrude out from the unit and may
be dangerous.
Do not use unauthorized products.
Notes
Insert an SD memory card with the contact
surface facing down, and press on the card
until it clicks and completely locks into place.
Press and hold MENU to display
Picture Adjustment.
Refer to Changing the picture adjustment.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
RD, RI : XXX7020
• AVH-P6350BT/XNRD, XNRI

AVH-P6300BT/XNUC
12
1234
1234
C
D
F
A
B
E
Remote control
1 5
6
Part Operation
1Thumb pad Click to recall Menu. Use to select a menu
on the DVD menu.
2RETURN
Press to display the
PBC (playback con-
trol) menu during PBC
playback.
3
Press to pause or re-
sume playback.
Press to return to the previous track (chap-
ter).
Press to go to the next
track (chapter).
Press to stop play-
back.
4/(FOLDER/P.CH)
Press to select the
next/previous folder.
Press to recall radio
station frequencies as-
signed to preset tun-
ing keys.
Part Operation
5BAND/ESC
Press to select the
tuner band when
tuner is selected as a
source. Also used to
cancel the control
mode of functions.
Press to switch be-
tween modes when
playing discs with
compressed audio
and audio data (CD-
DA) such as CD-
EXTRA and MIXED-
MODE CDs.
6
MENU Press to display the DVD menu during
DVD playback.
TOP MENU Press to return to the top menu during DVD
playback.
7
AUDIO
Press to change the
audio language during
DVD playback.
Press to switch audio
output for Video CD/
DivX.
SUBTITLE
Press to change the
subtitle language dur-
ing DVD/DivX play-
back.
ANGLE Press to change the viewing angle during
DVD playback.
8REAR SRC
Press to cycle through
all the available rear
sources.
Press and hold to turn
the rear source off.

AVH-P6300BT/XNUC 13
5678
5678
C
D
F
A
B
E
2.4 CONNECTION DIAGRAM
Connecting the power cord
   
   
 
This product
Microphone (supplied)
4 m (13 ft. 1 in.) Fuse (10 A)
RGB input
Wired remote input (WIRED REMOTE INPUT) Hard-wired remote control adaptor can be connected (sold separately).
Microphone input Jack (MIC)
17 cm (6-3/4 in.)
17 cm (6-3/4 in.)
Yellow Connect to the constant 12 V supply terminal.
Fuse resistor
Red Connect to terminal controlled by ignition switch (12 V DC). Black (chassis ground) Connect to a clean, paint-free metal location.
Left Right
Front speakerFront speaker
Rear speaker or Subwoofer (4 Ω)
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Violet Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything to Green and Green/black leads.
Subwoofer (4 Ω) × 2
Rear speaker or Subwoofer (4 Ω)
Orange/white Connect to lighting switch terminal. Fuse resistor
Pioneer IP-BUS accessories
Navigation system (AVIC-U220 (sold separately)).
Antenna input
IP-BUS cable
IP-BUS input (Blue)
26 pin cable (Supplied with Navigation system) Insert the 26 pin cable in the direction indicated in the figure. Please contact your dealer to inquire
about the connectable navigation system.
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note: · The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.
Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).
Ground side Power supply side Parking brake
switch
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. Note:
· Change the initial setting of this unit. The
subwoofer output of this unit is monaural.
• AVH-P6300BT/XNUC

AVH-P6300BT/XNUC
14
1234
1234
C
D
F
A
B
E
When connecting to separately sold power amp
 
 
 
 
 
 
Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC).
Connect with RCA cables (sold separately)
Rear speaker
Perform these connections when using the optional amplifier.
System remote control
Front speaker Front speaker
RightLeft
Rear speaker
Power amp (sold separately)
Power amp (sold separately)
Power amp (sold separately)
Subwoofer Subwoofer
To front output
To rear output
To subwoofer output
This product
Rear output (REAR OUTPUT) Front output (FRONT OUTPUT) Subwoofer output (SUBWOOFER OUTPUT)
13 cm (5-1/8 in.)
17 cm (6-3/4 in.)
13 cm (5-1/8 in.)
Connecting the system
This product
Wired remote input (WIRED REMOTE INPUT) Hard-wired remote control adaptor can be connected (sold separately).
IP-BUS input
HD Radio tuner
(sold separately)
IP-BUS cable (Supplied with HD Radio tuner)
When connecting the external video component and the display When using a display connected to rear video output This product’s rear video output and rear audio output are for connection of a display to enable passengers in the rear seats to watch the DVD, etc.
WARNING
Never install the display in a location where it
is visible to the driver while driving.

AVH-P6300BT/XNUC 15
5678
5678
C
D
F
A
B
E
This product
External video component (sold separately)
RCA cables (sold separately)
Audio inputs (AUDIO INPUT)
Video input (VIDEO INPUT)
Display with RCA input jacks (sold separately)
Rear monitor output (REAR MONITOR OUTPUT)To video input
To video output
To audio outputs
13 cm (5-1/8 in.)
Rear audio output (REAR MONITOR OUTPUT(AUDIO))
To audio inputs
RCA cables (sold separately)
17 cm (6-3/4 in.)
Mini pin plug cable (sold separately)
13 cm (5-1/8 in.)
It is necessary to change AV Input in
System Menu when connecting the exter- nal video component.
When connecting with a rear view camera When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIR- ROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
CAUTION
The screen image may appear reversed. The rear view camera function is to be used
as an aid to keep an eye on trailers, or while backing up. Do not use for entertainment pur- poses.
Objects in the rear view may appear closer or
more distant than they actually are.
Rear view camera input (REAR VIEW CAMERA IN)
This product
13 cm (5-1/8 in.)
To video output
Rear view camera (sold separately)
Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards.
Fuse resistor RCA cable
(sold separately)
CAUTION
You must use a camera which outputs mirror reversed images. It is necessary to set Camera Polarity properly in System Menu when connecting the rear view camera.

AVH-P6300BT/XNUC
16
1234
1234
C
D
F
A
B
E
Connecting the power cord
   
   
 
This product
Microphone input Jack (MIC)
Microphone (supplied)
4 m
Fuse (10 A)
RGB input
Wired remote input (WIRED REMOTE INPUT) Hard-wired remote control adaptor can be connected (sold separately). 17 cm
17 cm
Yellow Connect to the constant 12 V supply terminal.
Fuse resistor
Red Connect to terminal controlled by ignition switch (12 V DC). Black (chassis ground) Connect to a clean, paint-free metal location.
Left Right
Front speakerFront speaker
Rear speaker or Subwoofer (4 Ω)
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Violet Violet/black
Not used.
Green
Green/black
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything to Green and Green/black leads.
Subwoofer (4 Ω) × 2
Rear speaker or Subwoofer (4 Ω)
Orange/white Connect to lighting switch terminal. Fuse resistor
Pioneer IP-BUS accessories
Antenna input
IP-BUS cable
IP-BUS input (Blue)
Connection method
1. Clamp the lead. 2. Clamp firmly with
needle-nosed pliers.
Note: · The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.
Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).
Ground side Power supply side Parking brake
switch
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Note: · Change the initial setting of this unit. The
subwoofer output of this unit is monaural.
When you connect the separately sold multi-channel processor (e.g.,DEQ-P6600/DEQ-P7650) to this unit, do not connect anything to the speaker leads and systemremote control (blue/white).
• AVH-P6350BT/XNRD, XNRI

AVH-P6300BT/XNUC 17
5678
5678
C
D
F
A
B
E
When connecting to separately sold power amp
 
 
 
 
 
 
Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC).
Connect with RCA cables (sold separately)
Rear speaker
Perform these connections when using the optional amplifier.
System remote control
Front speaker Front speaker
thgiRtfeL
Rear speaker
Power amp (sold separately)
Power amp (sold separately)
Power amp (sold separately)
Subwoofer Subwoofer
To front output
To rear output
To subwoofer output
This product
Rear output (REAR OUTPUT) Front output (FRONT OUTPUT) Subwoofer output (SUBWOOFER OUTPUT)
13 cm
17 cm
13 cm
•When you connect the separately sold
multi-channel processor (e.g.,DEQ-P6600/DEQ-P7650) to this unit, do not connect anything to the speaker leads and system remote control (blue/white).
•When you connect the multi-channel
processor to this unit, refer to multi-channel processor’s installation manual for the connection method.
Connecting the system
DVD changer
(sold separately)
This product
Wired remote input (WIRED REMOTE INPUT) Hard-wired remote control adaptor can be connected (sold separately).
IP-BUS input
IP-BUS cable

AVH-P6300BT/XNUC
18
1234
1234
C
D
F
A
B
E
When connecting the external video component and the display When using a display connected to rear video output This product’s rear video output and rear audio output are for connection of a display to enable passengers in the rear seats to watch the DVD, etc.
WARNING
Never install the display in a location where it
is visible to the driver while driving.
This product
External video component (sold separately)
RCA cables (sold separately)
Audio inputs (AUDIO INPUT)
Video input (VIDEO INPUT)
Display with RCA input jacks (sold separately)
Rear monitor output (REAR MONITOR OUTPUT)To video input
To video output
To audio outputs
13 cm
Rear audio output (REAR MONITOR OUTPUT(AUDIO))
To audio inputs
RCA cables (sold separately)
17 cm
Mini pin plug cable (sold separately)
13 cm
It is necessary to change AV Input in
System Menu when connecting the exter- nal video component.
When connecting with a multi-channel processor
IP-BUS cable (supplied with multi-channel processor)
RCA cable (supplied with multi-channel processor)
Optical cable (supplied with multi-channel processor)
IP-BUS cable (Supplied with Bluetooth adapter)
Black
Bluetooth adapter (e.g. CD-BTB200) (sold separately) (AVH-P5350DVD only)
Microphone for hands-free phoning (supplied with Bluetooth adapter)
Black Optical cable connection box (CD-DD25)
(DEQ-P6600 :supplied with multi-channel processor) (DEQ-P7650 : sold separately)
To SWL
To SWR
Blue
Blue
Multi-channel processor (DEQ-P6600/DEQ-P7650) (sold separately)
This product
IP-BUS input
Black
Wired remote input (WIRED REMOTE INPUT)
Hard-wired remote control adaptor can be connected (sold separately).
Subwoofer output (SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
Optical output

AVH-P6300BT/XNUC 19
5678
5678
C
D
F
A
B
E
When connecting with a rear view camera When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIR- ROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
CAUTION
The screen image may appear reversed. The rear view camera function is to be used
as an aid to keep an eye on trailers, or while backing up. Do not use for entertainment pur- poses.
Objects in the rear view may appear closer or
more distant than they actually are.
Rear view camera input (REAR VIEW CAMERA IN)
This product
13 cm
To video output
Rear view camera (sold separately)
Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards.
Fuse resistor RCA cable
(sold separately)
CAUTION
You must use a camera which outputs mirror reversed images. It is necessary to set Camera Polarity properly in System Menu when connecting the rear view camera.
Connecting and installing the optical cable connection box
WARNING
Avoid installing the optical cable connection
box in locations where the operation of safety devices such as airbags is prevented by this unit. Otherwise, there is a danger of a fatal ac- cident.
Avoid installing the optical cable connection
box in locations where the operation of the brake may be prevented. Otherwise, it may re- sult in a traffic accident.
Fix the optical cable connection box securely
with the hook and loop fastener or lock tie. If the unit is loose, it disturbs driving stability, which may result in a traffic accident.
CAUTION
Install this unit using only the parts supplied
with this unit. If other parts are used, this unit may be damaged or could dismount itself, which leads to an accident or other problems.
Do not install this unit near the doors where
rainwater is likely to be spilled on the unit. In- cursion of water into the unit may cause smoke or fire.
Connecting the optical cable 1 Connect the optical cable and ground lead to the main unit. Connect the optical cable so that it does not protrude from the main unit, as shown in the illustration. Fasten the ground lead to the pro- trusion on the back of the main unit.
1
1Screw
2 Connect the optical cable to the optical cable connection box.
1
1Optical cable
Installing the optical cable connection box When installing the optical cable con- nection box with the hook and loop fasten- er. Install the optical cable connection box using the hook and loop fastener in the ample space of the console box.
1 2
1Hook fastener 2Loop fastener
When installing the optical cable con- nection box with the lock tie. Wrap the optical cable and connection box with the protection tape and fasten with the power code using the lock tie.
1
2
1Wrap with the protection tape 2Fasten with the lock tie

AVH-P6300BT/XNUC
20
1234
1234
C
D
F
A
B
E
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
To keep the product quality after servicing, please confirm following check points.
No. Procedures Item to be confirmed
1 Confirm whether the customer complain has
been solved.
If the customer complain occurs with the
specific media, use it for the operation check.
The customer complain must not be
reappeared.
Display, video, audio and operations must be
normal.
3 DVD Measure playback error rates at the
innermost and outermost tracks by using the
test mode with the following disc.
DVD test disc (TDV-582)
Deterioration of mecha-drive can be
checked.
The error rate must be less than the
threshold value.
(Refer to the chapter of DIAGNOSIS for the
threshold value.)
4 DVD Play back a DVD.
(Menu operation; Title/chapter search)
Display, video, audio and operations must be
normal.
5 CD Play back a CD.
(Track search)
Display, audio and operations must be
normal.
6 FM/AM tuner Check FM/AM tuner action.
(Seek, Preset)
Switch band to check both FM and AM.
Display, audio and operations must be
normal. * If the reception sensitivity is poorer
than normal, the gasket on the FM/AM tuner
unit may be damaged or lost.
7 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
8 Appearance check No scratches or dirt on its appearance after
receiving it for service.
For check items concerning image and voice, please refer to the followings:
Check items concerning image Check items concerning voice
Block-noise Distortion
Crosscut noise Noise
Dot noise Low volume
Distorted image (Image skip) High volume
Low brightness Changes in level
Too bright Pause of sound
Color fading
Partial discoloration
2 Flap-mecha Check the operation of the flap mechanism. The flap mechanism operation must be
smooth without making the noise and
scratches.