Pioneer VSX-D1S User manual

Operating
Instructions
AUDIO/VIDEO STEREO RECEIVER
VSX-D15
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how
to operate your model properly. After you have finished reading the
instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power
outlet may sometimes differ from that shown in the explanatory
drawings. However, the method of connecting and operating the unit
is the same.
WARNING: To PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear panel.
Please write this serial number on your enclosed warranty card and
keep it ina secure area. This is for your security.
[For Canadian model]
CAUTION: To PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER QUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
ATTENTION: pour PREVENIR LES CHOCS ELECTRIQUES NE
PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR
UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT,
SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN
LAISSER AUCUNE PARTIE A DECOUVERT.
RETURN function
This function returns the unit to a set of initial settings and ready
to broadcast tuner. This is helpful during troubleshooting or when
no sound is output. For details, refer to ‘‘“FRONT PANEL
FACILITIES,” page 19.
RESET function
Use this function when normal operation becomes impossible
because of external influences such as static electricity or lightning,
or when operation is impossible even when operation switches are
pressed. Press the RESET switch to return to normal operating
conditions.
If you press this switch, the entire contents of the memory are
cleared.
About the Demonstration Mode
© The demonstration is activated by turning on the power switch
while holding down the MUTING switch (from power standby
condition). The demonstration will appear on the display.
° Press any other switch to cancel the demonstration.
PIONGER
The future of sound and vision.

IMPORTANT
The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert the user of the presence of
uninsulated ‘‘dangerous voltage’’ within the product's
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
r————
SAFETY
INSTRUCTIONS
READ INSTRUCTIONS - All the safety and operating
instructions should be read before the appliance is
operated.
RETAIN INSTRUCTIONS - The operating instrucions
should be retained for future reference.
HEED WARNING ~ All warnings on the appliance and in
the operating instructions should be adhered to.
FOLLOW INSTRUCTIONS - All operating and use in-
structions should be followed.
WATER AND MOISTURE The appliance should not
be used near water - for example, near a bathtub,
washbowi, kitchen sink, laundry tub, in a wet base-
ment, or near a swimming pool, etc.
LOCATION - The appliance should be installed in a
stable location.
WALL OR CEILING MOUNTING The appliance
should not be mounted to a wall or ceiling.
VENTILATION = The appliance should be situated so
that its location of position does not interfere with
its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or,
placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through
the ventilation openings.
HEAT The appliance should be situated away from
heat sources such as radiators, heat registers,
stoves, or other appliances {including amplifiers)
that produce heat.
POWER SOURCES The appliance should be con-
nected to a power supply only of the type de-
scribed in the operating instructions or as marked
on the appliance
POWER-CORD PROTECTION - Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords
at plugs, convenience receptacles, and the point
where they exit from the appliance.
POLARIZATION - If your purchased product is pro-
vided with a polarized power plug, please read the
folowing instructions. This product is equipped
with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
CLEANING The appliance should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or
other volatile liquids since they may corrode the
cabinet.
Note to CATV system installer
This
reminder
is
provided
to
call
the
CATV
system
installer’s
attention
to
Article
820-22
of
the
NEC
that
provides
guidelines
for
propeig
rounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building,
as
close
to
the
point
of
ta
ble
entry
as practical.
2
<ARB1272>
CAUTION
RISK OF ELECTRIC SHOCK
OO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK}. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
POWER LINES — An outdoor antenna should be located
away from power lines.
NONUSE PERIODS — The power cord of the appliance
should be unplugged from the outlet when left un-
used for a long period of time.
OBJECT AND LIQUID ENTRY - Care should be taken
DAMAGE REQUIRING SERVICE
‘sO that objects do not fall and liquids are not spilled
into the enclosure through openings.
The appliance
should be serviced by a Pioneer authorized service
center or qualified service personnel when:
The power-supply cord or the plug has been dam-
aged; or
Objects have fallen, or liquid has been spilled into
the appliance; or
The appliance has been exposed to rain: or
The appliance does not appear to operate normally
or exhibits a marked change in performance; or
The appliance has been dropped; on the enctosure
damaged.
SERVICING - The user should not attempt to service
the appliance beyond that described in the opera-
ting instructions. For all other servicing, contact the
nearest Pioneer authorized service center.
WIRE
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
The exclamation point within an equilateral triangle is
intended to alert the user of the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
OUTDOOR ANTENNA GROUNDING - !f an outside an-
tenna is connected to the antenna terminal, be sure
the antenna system is grounded so as to provide
some protection against voltage surges and built
up Static charges.
In the U.S.A. section 810 of the Nationat Electrical
Code, ANSI/NFPA No. 70-1984, provides informa-
tion with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and require-
ments for the grounding electrode. See Fig, A.
CART An appliance and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
NEC — NATIONAL ELECTRIC CODE
ANTENNA
LEAD IN
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810 =. 20)
GROUNDING CONDUCTORS
(NEC SECTION 810.21)
POWER SERVICE GROUNDING
FIG. & ELECTRODE SYSTEM
(NEC ART 250, PART H}

CONTENTS
BEFORE OPERATING, ADJUST THE POSITION OF THESE SWITCHES ..0.0.... ccc ceccec eee eneeesene neers 4
FEATURES coscssesvsess Ji25s Waker nie itaciae tes eiieuee pinecteadivtes wedieaetata ren vdeesy old ce aeadag eek eeebeereeaieeed 4
BLOCK DIAGRAM cisscecfaidceis ccs pos cene veces ssees cate cand ease Se tadaad as awea dea oe Ualeudacnee cota ceaesesebicedidSeauetads 5
ACCESSORY ITEMS oc scccdcssacveroced sagatvenedusadaacsnicptsintndee sdez sue scene endpaeey etamacatvertaneed Tasca sstveeedse ees 5
DSSS (Digital Simulated Stereo System)........cccceecesecnec eee nceeeee eeu eeu eeu eeeeeeeneeseeenenneseaeneeeteeee ees 5
SURROUND MODE 3.5 sci se0ecenesvedcevecds as caey cos teecedsscukiwaddevesautcdedecdacedteageveassecoareddaessdarecdaeasadacenea 6
CLO NINTROMSI@INO@IRANRMIRGEIE — Basic Connections ..............ccccccececcecee nee eeeeseceeeseeceaeetaeeeeseentoess 7
ONIN SOnRIOINEGEENsemeams — Additional Audio/Video Component ...............csecesceeeneeeeeeseeeeees 13
FRONT: PANEL FACILITIES icc cscs codes ccesceschccvcevew cman vocuanaeh covcbech uc ecuusck gat cadeccSecdctetaanlees Oaauves 19
REAR: PANEL: FACILITIES ‘cc cccctssieceecedee stesa ice erecdvtcca'c sua estes coudadeschsceugtdsdsacdaacescuacadia sa seeaseves 24
SUOMI RO ove Fura dary ed ceria cnc taee Geren vededa aye Ueeuhsegdeqweseberganasdvesbovedandedsadeed ley etetewds Seen iads aaeveaseacaes 27
MANUAL TUNING \.c.cccccsceccsccsnsicxesccacseccartschaedcavesuscevccecheceebeeteeweducavenaa vayasevsausbdection¥e saaeasaae 27
AUTO TUNING foes sconce Seacnandinnsadelons See Cacve cea uc vans Gomeues dupciedueedes wad danelde ndaniuaneiade Bee tisaeadaabadeaceder’s 27
DIRECT ACCESS TUNING sinsscscttcvecisciccedangabbucathccs desiees doe deety ontasdeecdvaayveauetssdancbiay decedaesegaey ees 27
PRESET TUNING “sin Svcccnc sae dvsivecde cede vues des boehee eget wana Gaceleds vceu o¥oe vee Seatea dea hucd Metvecitiwcntantvawehiwdes : 28
SHORT-TIME RECEPTION OF CONSECUTIVE STATIONS — Memory scan............ccccceceeeeeeeeeeeenes 29
NAMING: A STATION 3 c¢ cic eecociwcavastaveeganea sive seas ae snegeedecdepcavded evuGvexececascceapedsvavaeeseseuend pdsedevesias 30
HITS (Hyper Intelligent Tuning System) .............cccececececcccecececeeeeeeeeeeeseneeaseceseceaeeeeeustensenereeuess 31
AM BROADCAST BEAT INTERFERENCE REDUCTION — AM B.R.(AM Beat Reduction)...............08- 31
OPERATING THE AUDIO COMPONENT S (iRsxsxnyNIny Dy 32
PLAYBACK 3 iii.ss cscs se satiaasioaet oditesacaceap dnduvesewateada ea eend davanens ccte Sided bua ide cu ae oandaudu ordered oeadines 32
RECORDING sisi ocdeceties caasesatads Shtwaedeceuadedsoucagh aonasee sovedbit Suuatdeadeadv ota euddetact cadae sadvedeuagweua soveaede 32
GRMN ae shasta attest DRS Palast am! 34
PLAY BACK icsesecicsstatecniaassaasusbsotansntanne ule cd eves ies actives queaegaeweet uudyedenadaaveaseses dabaasswaneoanean ties 34
VIDEORECORDING wesnccwevscecthraistensudeiieteendesety cobigedethvaite Vest yak ei etc neds loon ssetassiauscaticeeeseeeaaaieen 34
USING SURROUND SaSsIIIIIIIIS Sn 35
DOLBY PRO LOGIC SURROUND AND DOLBY 3CH LOGIC... ee ceececeessssenseenseseteneeeneees 35
JAZZ, DANCE, ‘CHURCH, HALL, THEATER: 0... ccccseccsesssswvsnsdaecetesnescsieescadeesisaveevisaesavaredeavesaess 35
SOUND QUALITY, SOUND FIELD, AND PICTURE QUALITY ADJUSTMENT ————————————————'7 36
HOW TO USE THE TONE CONTROL ...........ccccee sec eenec eee ecneceeeeeeaeeaeeeeeeeeseeseeeeenenseareeeeeeeneeases 36
HOW TO USE THE ACOUSTIC MEMORY .............:sccececsceeeeeceecesa eee seeeeesesseessseeeeeeseeseesasesentages 36
HOW TO USE THE SOUND FIELD MEMORY ................ccccecceceecece eee eseececceeaesaeeaeneeneereneeeaseueaees 37
HOW TO USE THE ENHANCER AND SPLIT SCREEN ........... 0. ccc ceceeeeeceeceececeeseusecueeveusensseeenensnes 37
HOW TO USE THE ENHANCER MEMORY ..............:sccecssceeeceeceeeeeeeceeeeececeeteeteeeeeesereuenaenenaes 37
USING THE VIDEO SIGNAL SELECTOR (sss I INIIIII nnn 38
USING MULTI-ROOM AND SOURCE (MR & S) [SiR SR RRs RRn gn 38
Selva dads aaa acing dictnacsttacen sods ti pottaeeacianeeaateaeee syed 40
HINFS: FOR BETTER RECEPTION... 200. ccevies cece edscetenenvsdiusacewengehedepdcecwedoniasesdoasshnaneddbabederecseede’s 48
FROUBLESHOOTING wn. iivevcv nite ta cadet casi esiuwededsy cvtededanateidecguldcund dnseicuseedeeend sas sibeoessiwanenedguctues 49
SPECIFICATIONS tiie. ti cen ec douse cecccdeeesovntwecectees sh ven ydskanwegsndwabecds vavencedbencsdedsipavedevedsesdesamvedvaeade 51
3
<ARB1272>

BEFORE OPERATING, ADJUST THE POSITION OF
THESE SWITCHES
TWO VOLTAGE SELECTOR SWITCHES
Only multi-voltage models are provided with these switches. U.S.,
Canadian, European, U.K. and Australian models are not provided with
these switches.
Mains voltages in Saudi Arabia are 127 V and 220 V only. Never use
this modei with 110 V setting in Saudi Arabia.
The line voltage selector switches are on the rear panel. Before your
model is shipped from the factory, these switches are set to the power
requirements of the destination. Check that they are set properly before
plugging the power cord into the household wall socket. If the voltage
is not properly set or if you move to an area where the voltage
requirements differ, adjust the selector switches as follows.
1. Use a medium-size screwdriver.
2. First, insert a screwdriver in the groove of the voltage selector at
the right, and adjust so that the tip of the groove points to the voltage
value of your area.
3. Next, insert a screwdriver in the groove of the voltage selector at
the left and adjust until the voltage is the same as at the right.
TWO VOLTAGE SELECTORS
CAUTION: TWO VOLTAGE SELECTORS
2
CHANNEL STEP/FM DE EMPHASIS SWITCH
(Not available on U.S. and Canadian models)
The unit has been factory preset to the channel allocation and de-
emphasis value for the area in which it is to be sold. If these values are
set incorrectly, the frequency display may stop at the wrong frequency,
or sound may be distorted, resulting in an inability to reproduce reception
signals at their proper sound quality. For this reason, be sure to confirm
that the values are set correctly before first using the unit.
[100kHz/10kHz/75zs] position:
Set to this position for areas with an FM reception step of 100kHz, AM
10kHz, and de-emphasis 75ys.
[S5O0kH2/9kHz/50us] position:
Set to this position, for areas with an FM reception step of 50kHz, AM
9kHz, and de-emphasis 5Ous.
NOTE:
When unsure about the channel allocation and de-emphasis values for
your area, consult your dealer for correct information.
CHANNEL STEP
/FMDE-EMPHASIS
acitov| A
a
220V
110V
120V-127V y40V
Pr : D
20V-127V
29N
Medium-size NOTE:
screwdriver
VOLTAGE SELECTORS
SOkHz/5OxS ff [100kHz/75uS FM
10kHz
SkHz =a AM
Both switches must be in the same switch
setting; otherwise, unit can be damaged.
FEATURES
e DOLBY PRO LOGIC SURROUND performed by a
Digital Signal Processor (DSP).
¢ DSP provides five Sound Field Control (SFC) simulated
surround settings.
© Multi-Room & Source
Using this unit in combination with the optional MR-100 Multi-Room
System Remote Control Sensor Unit lets you enjoy different sources
in different rooms at the same time.
4
< ARB1272>
© Independent tone control of front, center, and rear
channels is possible.
You can make tone adjustments to front (L, R), center, and rear (L, R)
channels independently, for much finer control over sound quality.
¢ AM beat reduction
* Equipped with the JOG dial, designed ior easier
operation.
*
Digital
Simulated
Stereo
System
(DSSS)
* Audio/Video programmable remote control unit.

BLOCK DIAGRAM
TAPEZ
PLAY
DIRECT
vcRi
vVCRZ
vVCR3
pse ©) SUPER WOOFER
PRE OUT
TAPE? REC
VOR| REC
VOR? REC
© § 7 MULTI ROOM & SOURCE
© » 4 SUB FUNC OUT
REC SEL SOURCE
B®:
BUFFER
VIDEO
-(3"9)
“MONITOR
VIOEO
v
BUFFER
.
°
vor
ee
=
TO
MONITOR
Tate
tur
ae
|
pburreR
TO
MONITOR
1
ak
9)
veri
iene
Tv2
ie
Meee
MULTI ROOM &
SOURCE VIDEO OUT
VCRI REC
i >—O
VCR? AEC
ACCESSORY ITEMS
—~ 2 OC
FM T-type Antenna AM Loop Antenna Audio/Video programmable Template x 2 Alkaline dry cell battery x4
remote control unit (size ‘AAA’ (LRO3/AM-4)
DSSS (Digital Simulated Stereo System)
Special DSP circuitry gives you simulated stereo sound from monaural
sources.
This operates even when a monaural signal is input into both the left
and right channels, or only one of the channels. When a signal is input
into only one channel, the output level is lower than when the signal
is input into both the left and right channels.
You can also enjoy combining it with surround modes other than DOLBY
PRO LOGIC SURROUND or DOLBY 3CH LOGIC.
5
<ARB172>

SURROUND MODE
—_—
eee
This unit is equipped with DOLBY PRO LOGIC SURROUND. There’s also
a DSP (Digital Signal Processor), with a choice of five SFC (Sound Field
Control) simulated surround settings.
© JAZZ:
This gives you the sound field of a jazz club.
* DANCE:
A “hot’’ high-energy sound, with extra reverb for greater ambience.
© CHURCH:
The sound field of a church, ideal for reproducing the rich sound of a
pipe organ.
* HALL:
You can enjoy a convincing hall sound.
© THEATER:
These effects are ideal when you want to enjoy stereo movie soundtrack
sources that don’t bear the O10 [potey surrounn | mark.
With video software bearing the pi@ mark,
switch DOLBY PRO LOGIC SURROUND and THEATER on. This will
give you the sound field realism and movement of Dolby Surround
together with the ambience and excitement of a movie theater.
* DOLBY PRO LOGIC SURROUND
Choose
this
setting
for
movies
and
music
(especially
Video
Discs
and
video
tapes
bearing
the
(0
[pousy
surrounn
|
mark)
playback.
DOLBY
PRO
LOGIC
SURROUND
continuously
detects
the
size
and
direction
of
the
dominant
signal
and
cancels
undesirable
crosstalk,
thereby
providing
signal
emphasis.
It
makes
you
clearly
perceive
the
directions
where
music
comes
from.
Real
flow
of
sound
also
can
be
re-created
naturally
using
this
feature.
You
can
feel
as
if
being
in
the
outstanding
and
expansive
sound
field.
When
using
DOLBY
PRO
LOGIC
SURROUND,
a
delay
time
setting
of
20
ms
is
commonly
used.
Use
a
different
setting
if
you
prefer.
¢ DOLBY 3 CH LOGIC
By
adding
the
signal
for
the
rear
speakers
to
the
signal
for
the
front
speakers,
the
front
three
channels
(front
L,
front
R,
and
CENTER)
provide
a
much
wider,
more
spacious
sound
field
than
possible
during
ordinary
stereo
playback.
er
rerun
arenes
DOLBY PRO LOGIC SURROUND and DOLBY 3 CH LOGIC are equipped
with the following 3 positions for the CENTER MODE.
When using center speaker(s):
¢ NORMAL
Low range frequencies, which have little effect on directionality and
positioning, are routed to the left and right front speakers. So you can
use relatively small size speakers as the center speakers.
© WIDE
If you use large size center speaker(s), choose this setting. The full
frequency range of the center speakers, from low to high, is routed to
the center speaker.
When not using a center speaker:
¢ PHANTOM
The signal which would have been sent to the center speaker is divided
equally between the left and right front speakers.
SURROUND SPEAKER INSTALLATION EXAMPLE
To get the best effect out of the surround system, place the speakers
as shown below.
An example for center speaker location
When using dual center speakers
CENTER SPEAKER
FRONT
SPEAKER
SPEAKER
6
< ARB1272>
When using a single center speaker
NOTE:
¢ To avoid interference with the picture on a nearby TV set, use
magnetically shielded speaker systems. This is particularly important
for the center speaker since it is usually located closest to the TV.
* Position the left and right channel speakers at equal distances from
the TV set and approximately six feet from each other.
© Position the center speaker above, below, or behind the TV set. Sound
may not appear to coincide with the picture if you position it next to
the TV set. .
© Rear speakers are best positioned slightly above ear level.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under one or more of the
following patents: U.S. numbers 3,632,886, 3,746,792 and
3,959,590; CANADA numbers 1,004,603 and 1,037,877.
“Dolby’’ and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
Manufacturé sous licence de Dolby Laboratories Licensing
Corporation. En outre, sous license d'un ou plusiers des brevets
suivants: numéros américains 3,632,886, 3,746,792 et
3,959,590: numéros canadiens 1,004,603 et 1,037,877. Le
terme ‘‘Doiby”’ et le symbole Double-D sont des marques dépsoées
de Dolby Laboratories Licensing Corporation.
Note:
Dolby Surround will not operate correctly if the signal passes through
a graphic equalizer.
When using Dolby Surround, turn off the TAPE 2 switch or set the
graphic
equalizer
for
flat
response
or
to
its
‘‘through
(defeat)’’
(or
off) setting, if it has one.

CONNECTION CHART (1)
—
Setting Up the AM Antenna
® Insert the claw on the bottom of the antenna into the groove in the leg.
¢ Place the antenna on a level surface and rotate it to locate the
orientation that yields the best reception.
¢ Use the attachment hole in the leg to screw to wall or other location,
then insert the claw on the bottom of the antenna into the groove
in the leg (fixing the antenna in the direction that gives the best
reception).
Lead wire
Lead wire
CONNECTING THE POWER CORD
(For U.S. and Canadian models)
Household electrical outlets are provided with specific polarity, a live
side and aneutral (ground) side. This unit utilizes such polarity in order
to improve sound quality. As shown in the illustration, be sure to insert
the power plug so that its blades match the width of slots in the outlet.
AC wall socket
Long slot is neutral
(ground) side.
Insert the wide blade
into the ground side slot.
e |ilustration shows U.S. and Canadian models.
Precaution regarding installation position of cassette deck.
If the cassette deck is installed in the @ positions shown in the
drawing below, it may be adversely affected during playback. If possible,
it’s better to install it in the 8) position.
THE S-VIDEO CONNECTORS
When using a VCR 1, VCR 2, VCR 3, VDP/CDV and monitor TV which
has S-VIDEO connectors, they can be connected to the S-VIDEO
connectors.
For the operation of components connected to S-VIDEO connectors,
refer to the instruction manuals of the corresponding components.
NOTE:
© In this unit, the S-VIDEO connectors (Y-C separate) and the regular
pin jacks are independent, so any signal input through a pin jack must
be output from the pin jack, and any signal input through an S-VIDEO
connector must be output through the S-VIDEO connector.
© The S-VIDEO connector is for video portion only, so be sure to make
audio connections also.
How to use S-VIDEO connectors
S-VIDEO jack
Check the position of aN
the holes and insert.
° °
9° °
[=]
| t | <e plug
For the method of switching the monitor TV S-VIDEO connector/VID EO
jack, refer to the monitor TV's instruction manual.
<ARB1772>

CONNECTION CHART (1)
Basic Audio Component Connections
¢ FM, AM antenna connection
¢ Turntable
® First cassette deck
© Compact disc player
Accessory
T-type FM antenna _
Cassette deck
Accessory
AM loop antenna
Stretch the antenna out
to its full “‘T’’ shape,
! and affix to a wall, etc.
antes —J
CE
To
AC
OUTLETS
Ce
To
AC
OUTLETS
Turntable
CD player
8
< ARB1272>

CONNECTION CHART (1)
Basic
Video
Component
Connections
(1)
¢ First VCR
VHF antenna UHF antenna
First VCR
¥* S (video) connection. See page 7.
< ARBI272>

CONNECTION CHART (1)
Basic
Video
Component
Connections
(2)
* Video Disc Player (Compatible Laserdisc player)
¢ TV tuner
® First monitor TV
AUDIO
OUT
VIDEO
OouT
Video Disc Player
(Compatible Laserdisc player)
es —-O—O-—®
MI GDE _
Meee:
+ or .
VIDEO Ss
TY Se
TV
tuner,
etc
First
monitor
TV
%& S (video) connection. See page 7.
10
<ARB1272>