Pittsburgh Automotive 96524 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
96524
1000 Lb. Capacity
Engine Support Bar
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 23f
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2023 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. 96524
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 4
Setup .......................................................... 4
Operation.................................................... 5
Maintenance............................................... 5
Warranty ..................................................... 8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
1. Study, understand, and follow all
instructions before using this tool.
2. Do not exceed rated capacity.
3. Wear eye protection that meets ANSI/ISEA Z87.1.
4. Support device only. Install or remove the engine
support tool only after lifting the engine.
5. Make sure tool foot contact points
can support the load.
6. Make sure the engine is secure before
removing the engine support tool.
7. Failure to heed and understand these
instructions and markings may result in
personal injury and/or property damage.
8. Position this tool on areas of the vehicle as
specified by the vehicle manufacturer.
9. No alterations shall be made to this product.
10. Use only replacement parts approved
by the manufacturer.
11. Maintain the Engine Support. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the tools operation. If damaged, have
the tool repaired before use. Many accidents
are caused by poorly maintained tools.
12. Use the Engine Support in accordance with these
instructions and in the manner intended for the
particular type of tool, taking into account the
working conditions and the work to be performed.
Use of the tool for operations different from those
intended could result in a hazardous situation.
13. Use the Engine Support for short-term lifting
projects only. The Engine Support is not
constructed to endure extended term use.
14. Do not work on an engine that is supported only
by the Engine Support. Do not take any action
that will jar, jostle or move the engine. Moving
the engine in any way creates a safety hazard
and may cause the engine to fall resulting in
serious personal injury or property damage.
15. Do not work underneath an engine while it
is supported only by the Engine Support.
16. Be aware of dynamic loading! Suddenly
swinging or dropping load may briefly create
excess load causing product failure.
17. This product is not a toy. Keep it
out of reach of children.
18. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.

Page 3For technical questions, please call 1-888-866-5797.96524
SAFETYOPERATIONMAINTENANCE SETUP
19. Keep children and bystanders away while
using the Engine Support. Distractions
can cause you to lose control.
20. Stay alert, watch what you are doing and use
common sense when operating the Engine
Support. Do not use it while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating tools
may result in serious personal injury.
21. Use safety equipment. Safety equipment such
as dust mask, non-skid safety shoes, hard hat,
hearing protection, and work gloves used for
appropriate conditions will reduce personal injuries.
22. Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the tool in unexpected situations.
23. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
24. Maintain labels and nameplates on
the tool. They carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
25. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-888-866-5797. 96524
SAFETY OPERATION MAINTENANCESETUP
Specifications
Maximum
Capacity 1,000 Pounds
Overall
Dimensions 59″ x 9-1/2″ x 12-1/4″
Weight 31.4 lbs.
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Inspect tool before use, looking for damaged, loose, and missing parts.
If any problems are found, do not use tool until repaired.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Assembly
1. Using provided Nuts (2) and Bolts (4), attach
Standing Blocks (3) to Standing Brackets (1) for both
sides of the Engine Support. Tighten the Nuts (2).
2. Mount both Standing Brackets to Beam
(5) with Wing Screws (7) and Washers
(6). Tighten the Wing Screws (7).
3. Insert the Support Screws (11) upwards
through the Beam, add Large Washers
(9) and screw onto Handles (10).

Page 5For technical questions, please call 1-888-866-5797.96524
SAFETYOPERATIONMAINTENANCE SETUP
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual
including all text under subheadings therein before set up or use of this product.
1. Read the owner’s manual of the engine to
be lifted to determine it’s lifting points.
Note: Do not try to move a running or hot engine.
Allow sufficient time for the engine to cool down
entirely before beginning any operations.
2. Park the car on a flat surface, apply the
parking brakes and check the wheels.
3. Loosen Wing Screws (7) and spread Standing
Bracket (1), and locate rubber cushions
of the Standing Brackets over the lips
adjacent to the fenders of the car. Tighten
the Wing Screws (7). Center the engine
support bar assembly over the engine.
4. Attach the Chains (12) to the engine at
the appropriate lifting points, then loop
the Chains securely to the flange on the
bottom of the Support Screws (11).
5. Turn the Handles (10) clockwise until the Chains
are taut and the engine is held securely.
6. Loosen engine mounts. Turn the Handles (10)
at 1/4″ clockwise turns until the entire engine’s
weight is supported by the chains. Additionally
loosen/disconnect the engine mounts.
7. Lower and reconnect the engine when
finished working. Clean, then store the
tool indoors out of children’s reach.
Note: The Engine Support is not intended to
be used as a long-term suspension device.
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs, have the
problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general condition
of the Shop Press and Bottle Jack. Check for:
• loose hardware
• cracked, bent or broken parts
• loose or missing parts
• misalignment or binding of moving parts
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.

Page 6 For technical questions, please call 1-888-866-5797. 96524
SAFETY OPERATION MAINTENANCESETUP
Parts List and Assembly Diagram
Parts List
Part Description Qty
1 Standing Bracket 2
2 Nut M10 2
3 Standing Block 2
4 Bolt M10x30 2
5 Beam 1
6 Small Washer 2
7 Wing Screw 2
Part Description Qty
8 Rubber Grip 4
9 Large Washer 2
10 Handle 2
11 Support Screw 2
12 Chain 2
13 Rubber Cushion 4
14 Washer 10 2
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 7For technical questions, please call 1-888-866-5797.96524
SAFETYOPERATIONMAINTENANCE SETUP
Assembly Diagram
8
10
9
11
7
6
3
4
1
13
2
14
12
5

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.