PL&T Shoplight With Sensor User manual

LED Portable Luminaire
Rated:120V-60Hz 40W
4 UNITS MAXIMUM
PACKAGE CONTENTS
READ ALL THE INSTRUCTIONS AND SAVE THIS INSTRUCTION SHEET.NOT READING
THE INSTRUCTIONS MAY CAUSE RISK OF FIRE OR PERSONAL INJURY
STYLE 1 SUSPENSION INSTALLATION INSTRUCTIONS:
1. Mounting surface must be capable of supporting the fixture. If the surface is made of plaster board,
we recommend that you use minimum #8 screw eye hooks with plastic anchors (included) or expansion
bolts (not included). If installed onto a plaster board surface, We recommend minimum 3/8” thick.
NOTE:
1. This fixture complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
2. To install onto a plaster board surface, plaster board requires minimum 3/8” thick.
2.Install the 2 plastic anchors 47 1/4” apart, then screw the eye hook into each anchor.
3.Install one “S” hook into each end of the chain, then crimp the “S” hook end which is attached to the
chain with pliers.(Leave one side open from the “S” hook) Repeat step for the second chain provided.
4.Install the “S” hook from one end of the chain into the end cap of the LED lamp, then crimp
the hooks end with pliers. Repeat same step for the opposite side.
1
2
&
Shoplight With Sensor Installation Instructions
3
4
X6
CAUTION: To reduce the risk of fire, electric shock or injury to people:
Turn off the switch and circuit breaker before installing this LED lamp.
Suitable for dry locations.
Not for use with dimmers.
Install directly beneath a ceiling-mounted receptacle.
Use only insulated staples or plastic ties to secure the cord.
The power cord is 4.9 feet long
Not intended for recessed installation or in ceiling.
Do not install directly over a heat source (stove, etc.)
Use safety precautions. Safety eye glasses and gloves are recommended.
Installation should not be made on a radiant-heating ceiling.
Injury to people and damage to the lamp and/or mounting surface may
result if the lamp is pulled from the surface. To reduce the likelihood of
such injury or damage, mount only on a mechanically sound surface.
Do not alter the plug or power supply cord in any way or try to install
this product in any other method besides methods shown on this sheet.

STYLE 2 SURFACE MOUNT INSTALLATION INSTRUCTIONS:
1. Mounting surface must be capable of supporting the fixture. If the surface is made of plaster
board, we recommend that you use minimum #8 screw eye hooks with plastic anchors (included)
or expansion bolts (not included). If installed onto a plaster board surface, We recommend minimum
3/8” thick. When the sensor is mounted at the recommended 9.2~11.5 foot height,motion will be detected in
the following areas:
3. Lift fixture up to screws and slide to one side to secure into place. Screw size:ST4X30.
4. Plug the power supply cord into the electrical outlet.
LINKING MULTIPLE SHOPLIGHTS
6. Plug the power supply cord into the electrical outlet.
2. Install the 4 plastic anchors 46 1/2” apart and 3.189” apart, then screw into each
anchor. Spacing between ceiling and cap nut should be at least 1/3”.
3
4
2
STYLE 1 AND STYLE 2 INFRARED SENSOR RANGE
5. Install the LED lamp with chains, one end at a time onto each screw eye hook. Once
installed, crimp each of the “S” hooks end with pliers. Please noted the on/off pull chain
is 9.8 inches long.
Link up 4 shoplights togetherConnect to additional shoplightConnect to Power Outlet
Shoplight
Max 16ft detection distance if walk perpendicularly
toward the sensor end of the shoplight
Max 6.5ft detection distance if walk parallel
toward the sensor end of the shoplight