Planet Networking & Communication POE-151 User manual
– 1 – – 3 –
– 2 – – 4 –
1. Introduction
Thank you for purchasing our POE-151 IEEE 802.3af Power
over Ethernet Injector, your Power over Ethernet Injector
package shall contains following contents:
1.1 Packet Contents
Check the contents of your package for following parts:
● PoweroverEthernetInjectorx1
● User’smanualx1
● PowerAdapterx1
● Powercordx1
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
cartonincludingtheoriginalpackingmaterial,andusethem
against to repack the product in case there is a need to
return it to us for repair.
1.2 Key Features
● Comply with IEEE 802.3af Power over Ethernet, IEEE
802.3/802.3u 10/100Base-TX
● Provide DC 48V power over RJ-45 Ethernet cable to
devicewithEthernetport
● Auto-detect of PoE IEEE 802.3af equipment, protect
devicesfrombeingdamagedbyincorrectinstallation
● WorkwithEIA568,category5,4-paircablesfor10Base-T
or 100Base-TX
1.4 Product Outlook
1.5 LEDdenition
LED Color Function
Power Yellow LightstoindicatethatthePOE-151
has power.
PoEready/
in-use Green Lightstoindicatetheportis
providing48VDCin-linepower.
1.3 Specication
Model POE-151
Ethernet
Connector
2xRJ-45
(1fordata+DCin,1forDataout)
EthernetData
rate
10/100Mbps
(varyonEthernetdeviceattached)
Input voltage DC48V,0.4A
Numberof
devicecanbe
powered
1
Ethernetcable TIA/EIA-568,Category5/5ecable
LEDindicator 1xpower,1xPoEready/in-use
Dimension
(WxDxH) 73x55x24mm
EMI FCCClassB,CEmark
Standard
Compliance
IEEE 802.3 Ethernet,
IEEE 802.3u Fast Ethernet,
IEEE802.3afPoweroverEthernet(PSE).
RJ-45Power
Insertion Pair Pair4,5,7,8(Mid-Span)
2. Installation
This product provides two different running speeds –
10Mbps, 100Mbps in the same device and automatically
distinguishesthespeedofincomingconnection.
This section describes the hardware features of POE-151.
Beforeconnectinganynetwork devicetothePOE-151, read
this chapter carefully.
2.1 Before Installation
Before your installation, it is recommended to check your
network environment. If there is any IEEE 802.3af devices
need to power on, the POE-151 can provide you a way
to supply power for this Ethernet device conveniently
and easily. The POE-151 equips with an AC-DC adapter
with DC 48V input and injects this DC power into the pin
of the twisted pair cable (pair 4, 5 and pair 7, 8 for Fast
Ethernet).
If there is very difcult to nd a power socket for AC-DC
Adapter of your non IEEE 802.3af networked device, the
POE-151 and POE-151S can provide you a way to supply
DCpowerforthisEthernetdeviceconvenientlyandeasily.
Note
The POE-151 and POE-151S can be installed
in pair. However, the use of third-party device
is allowed if the device complied with IEEE
802.3afstandard.
– 5 – – 6 –
2.2 POE-151, the Injector installation
1.Connect a standard network cable from Switch/worksta-
tion to “Ethernet” port of POE-151.
2.Connect the long cable that will be used to connect to
theremotedevicetotheport“Ethernet + DC”.
3.Connect the AC adapter to “DC 48V” of POE-151. The
powerLEDwillbesteadyon.
4.Connect with IEEE 802.3af devices, due to the capability
of IEEE 802.3af standard, the POE-151 can directly
connect with any IEEE 802.3af end-nodes like wireless
access point, VoIP phones and Internet camera where
support IEEE 802.3af In-line Power over Ethernet port.
Figure 1: Connection to IEEE 802.3af device
Once POE-151 detects the existence of an IEEE 802.3af
device, the LED indicator will be steady, ON to shows it is
providingpower.
Note
If the connected device is not fully complying
with IEEE 802.3af standard or in-line power
device, the LED indicator of POE-151 will not
besteadyon.
2.3 POE-151 and POE-151S, the IEEE 802.3af
Injector and Splitter installation
1.Connect a standard network cable from “Ethernet+DC”
of POE-151 to “Ethernet+DC” of POE-151S. The POE
LEDofPOE-151/POE-151Swilllightoncontinuance.
2.Connect the UTP cable in the package from “Ethernet”
ofPOE-151StotheRJ-45portofremotedevice.
3.ConnectproperDCplug from“DC OUT” of POE-151S to
remotedevice.
4.Power on the remote device and the LED indicator on
POE-151Swillremainson.
Figure 2: Connection architecture over POE-151/151S
Note
1. According to IEEE 802.3af standard, the
POE-151 will not inject power to the cable
ifnotconnectingtoIEEE802.3afdevices.
2. Please ensure the output voltage is correct
beforeapplyingpowertoremotedevice.
Other Planet Networking & Communication Laboratory Equipment manuals
