Planet Networking & Communication SGS-6310 Series User manual

Layer 3 Gigabit/10 Gigabit Stackable Managed Switch
SGS-6310 Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Switch Management.................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to the Console.................................................................... 7
 4.2 ConguringIPAddress......................................................................... 7
 4.3 Setting1000BASE-Xfor10GSFP+Port................................................. 9
 4.4 ChangingPassword.............................................................................. 9
 4.5 SavingtheConguration ...................................................................... 9
5. Starting Web Management .........................................................................10
 5.1 LoggingintotheManagedSwitchfromcopperports ............................11
 5.2 SavingCongurationviatheWeb ........................................................12
6. LEDIndicators...........................................................................................13
 6.1 SGS-6310-24T4X................................................................................13
 6.2 SGS-6310-24P4X................................................................................14
 6.3 SGS-6310-16S8C4XR..........................................................................15
7. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing Layer 3 Gigabit/10 Gigabit Stackable Managed
Switch,SGS-6310-16S8C4XR/SGS-6310-24T4X/SGS-6310-24P4X
Unless specied, “Managed Switch” mentioned in this Quick Installation Guide
referstotheSGS-6310-16S8C4XR/SGS-6310-24T4X/SGS-6310-24P4X.
Model Description
SGS-6310-16S8C4XR
Layer316-Port100/1000XSFP+8-PortGigabitTP/SFP+
4-Port10GSFP+StackableManagedSwitch
(Dual100~240VAC)
SGS-6310-24T4X Layer324-Port10/100/1000T+4-Port10GSFP+
StackableManagedSwitch
SGS-6310-24P4X. Layer324-Port10/100/1000T802.3atPoE+4-Port10G
SFP+StackableManagedSwitch
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
SGS-6310-16S8C4XR SGS-6310-24T4X SGS-631024P4X
QuickInstallation
Guide   
DB9toRJ45Interface
RS232 Console Cable   
Rack-mountAccessory
Kit   
ACPowerCord 2 1 1
SFPDustCap 28 4 4
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Switch Management
To set up the Managed Switch, the user needs to congure the Managed Switch
fornetwork management.The ManagedSwitch providestwo managementoptions:
Out-of-Band ManagementandIn-Band Management.
Out-of-Band Management
Out-of-band management is the management through console interface.
Generally, the user will use out-of-band management for the initial switch
conguration,orwhenin-bandmanagementisnotavailable.
In-Band Management
In-band management refers to the management by logging in to the Managed
Switchusing Telnetor HTTP,orusing SNMPmanagement softwaretocongure the
Managed Switch. In-band management enables the management of the Managed
SwitchtoattachsomedevicestotheSwitch.Thefollowingproceduresarerequired
toenablein-bandmanagement:
1. Log on to console
2.Assign/CongureIPaddress
3. Create a remote login account
4.EnableHTTPorTelnetserverontheManagedSwitch
In case in-band management fails due to Managed Switch conguration changes,
out-of-band management can be used for conguring and managing the Managed
Switch.
The Managed Switch is shipped with VLAN1 interface IP address
192.168.0.254/24 assigned by default. User can assign another
IP address to the Managed Switch via the console interface to be
able to remotely access the Managed Switch through Telnet or
HTTP.

5
3. Requirements
zWorkstations running Windows XP/2003/Vista/2008/7/8/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
Tera Term or PuTTY.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zManagement Port Connection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 TheabovePCisinstalledwithWebbrowser
Note
Itis recommended touse InternetExplorer8.0 orabovetoaccess
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
consoleportdirectlythroughPCwithouttheneedofNullModem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Tera Term program may be a good choice. The Tera Term can be accessed
fromtheStart menu.
1. Click START menu, then Programs,andthenTera Term.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:9600
Parity:None
Databits:8
Stopbits:1
Flowcontrol:None
Figure 4-2 Tera Term COM Port Conguration

7
4.1 Logging on to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
theterminalwilldisplay“running testing procedures”.
Then, the following message asks for the login user name and password. The
factory default user name and password are as follows as the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3 Managed Switch Console Login Screen
The user can now enter commands to manage the Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Accept command in lowercase or uppercase letter under console
interface.
4.2 ConguringIPAddress
The IP address conguration commands for VLAN1 interface are listed below.
Before using in-band management, the Managed Switch must be congured with
an IP address by out-of-band management (i.e. console mode). The conguration
commandsareasfollows:
Switch#cong
Switch_cong#interface vlan 1
Switch_cong_v1)#ip address 192.168.1.254 255.255.255.0

8
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPv4 Address: 192.168.1.254
Subnet Mask: 255.255.255.0
Figure 4-4 Conguring IPv4 Address Screen
To check the current IP address or modify a new IP address for the Managed
Switch,pleaseusetheproceduresasfollows:
ShowthecurrentIPaddress
1. On “Switch#” prompt, enter “show ip interface brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure4-5.
Figure 4-5 Showing IP Information Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Managed Switch
throughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter, enter “help”anytimeinconsoletogetthehelpdescription.

9
4.3 Setting1000BASE-Xfor10GSFP+Port
The Managed Switch supports both 1000BASE-X and 10GBASE-X SFP
transceivers by manual setting and the default SFP+ port speed is set in the ber
auto mode,sotheend-usercanplugthetransceiverdirectly.
In another example, the end-user has to force the ber connection with
1000BASE-X SFP transceiver in the tgigaethernet 0/1. The following command
congurationisrequired:
Switch#cong
Switch_cong#interface TGigaEthernet0/1
Switch_cong_tg0/1#no ber-auto-cong
Switch_cong_tg0/1#speed 1000
Switch_cong_tg0/1#exit
Figure 4-6 Setting 1000BASE-FX Screen
4.4 ChangingPassword
The default password of the switch is “admin”. For security reason, it is
recommended to change password and the following command conguration is
required:
Switch#cong
Switch_cong#username admin password planet2022
Switch_cong#
Figure 4-7 Changing Password Interface Screen
4.5 SavingtheConguration
InManagedSwitch, therunningcongurationle storesinthe RAM.Inthe current
version, the running conguration sequence running-cong can be saved from the
RAM to FLASH by write command, so that the running conguration sequence
becomesthestart-upcongurationle,whichiscalledcongurationsave.
Switch#write
Switch#write
Saving current conguration.
OK!
Switch#Jan 2 00:56:04 /startup-cong is wrote, TID:85bd29c0
Figure 4-8 Write Screen

10
5. Starting Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer,MozillaFirefox,GoogleChromeorAppleSafari.
PC/Workstation with
Web Browser
192.168.0.X
Managed Switch
IP Address:
192.168.0.254
RJ45/UTP Cable
Figure 5-1 IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch. Please note the Managed Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
For example, the IP address of the Managed Switch is congured with
192.168.0.254 on Interface VLAN 1, then the manager PC should be set to
192.168.0.x(wherex isanumberbetween 2and253,except1 or254),andthe
defaultsubnetmaskis255.255.255.0.
Thefactorydefaultusernameandpasswordareasfollows:
DefaultIPofInterfaceVLAN1:192.168.0.254
Username:admin
Password:admin

11
5.1 Logging in to the Managed Switch from copper ports
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.254 (that you have just set in console) to access the Web
interface.
2.When the following dialog box appears, please enter the congured username
“admin”and password“admin”(or theusername/password youhavechanged
viaconsole).TheloginscreeninFigure5-2appears.
Figure 5-2 Login Screen
3.Afterenteringthepassword,themainscreenappearsasshowninFigure5-3.
Figure 5-3 Web Main Screen of Managed Switch

12
4.The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheSwitchprovides.
Now, you can use the Web management interface to continue the Switch
management or manage the Managed Switch by console interface. Please refer to
theusermanualformore.
5.2 SavingCongurationviatheWeb
The conguration area is to show the content that is selected in the navigation
area. The conguration area always contains one or more buttons, such as
“Refresh”,“Apply”and“Reset”.
The “Apply” button indicates applying the modied conguration to the device. The
application of the conguration does not mean that the conguration is saved in
thecongurationle.
To save the conguration, you have to click “Save All” on the top control bar.
“Save All”functionisequivalenttotheexecutionofthewritecommand.
Figure 5-4 Save Cconguration

13
6. LED Indicators
6.1 SGS-6310-24T4X
System
LED Color Function
PWR
Green LightstoindicatethattheSwitchhaspower.
O Poweriso.
SYS Green Slowblinkstoindicatethesystemisnormallystartingup.
Interfaces
LED Color Function
LNK/ACT Green
Lights Indicatingthe portis running andthe connectionis
successfullyestablished.
Blinks Indicating that the switch is actively sending or
receivingdataoverthatport.
10GStatusLED
LED Color Function
LNK/ACT
(Ports25-28) Green
Lights Indicatingthe portis running andthe connectionis
successfullyestablished.
Blinks Indicating that the switch is actively sending or
receivingdataoverthatport.

14
6.2 SGS-6310-24P4X
System
LED Color Function
PWR
Green LightstoindicatethattheSwitchhaspower.
O Poweriso.
SYS Green Slowblinkstoindicatethesystemisnormallystartingup.
Interfaces
LED Color Function
1000LNK/
ACT Green
Lights Indicatingtheportisrunningat1000Mbpsspeed
andsuccessfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.
10/100LNK/
ACT Amber
Lights Indicatingtheportisrunningat10/100Mbps
speedandsuccessfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.
10GStatusLED
LED Color Function
10GLNK/
ACT Amber
Lights Indicatingtheportisrunningat10Gbpsspeed
andsuccessfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.
1000LNK/
ACT Green
Lights Indicatingtheportisrunningat1000Mbpsspeed
andsuccessfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.

15
6.3 SGS-6310-16S8C4XR
System
LED Color Function
PWR
Green LightstoindicatethattheSwitchhaspower.
O Poweriso.
SYS Green Slowblinkstoindicatethesystemisnormallystartingup.
Interfaces
LED Color Function
LNK/ACT Green
Lights Indicatingtheportisrunningandtheconnectionis
successfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.
10GStatusLED
LED Color Function
LNK/ACT
(Ports25-28) Green
Lights Indicatingtheportisrunningandtheconnectionis
successfullyestablished.
Blinks Indicatingthattheswitchisactivelysendingor
receivingdataoverthatport.

16
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource at the PLANET Web site rst to check if it could solve your issue. If you
needmoresupportinformation,pleasecontactPLANETsupportteam.
PLANETonlineFAQs:
http://www.planet.com.tw/en/support/faq.php?type=1
Supportteammailaddress:
[email protected]
SGS-6310-SeriesUser’sManual
https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=S
GS-6310&view=3#list
Copyright ©PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.