Planet Networking & Communication FGSW-1816HPS User manual

User’s Manual of FGSW-1816HPS
1

User’s Manual of FGSW-1816HPS
2
Trademarks
Copyright © PLANET Technology Corp. 2014.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the power cable to
disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power consumption, it
is strongly suggested to remove the power connection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PLANET 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP ComboWeb Smart Ethernet Switch User's Manual
FOR MODEL: FGSW-1816HPS
REVISION: 1.0 (July 2014)
Part No: EM-FGSW-1816HPS_v1.0 (2080-AK8080-000)

User’s Manual of FGSW-1816HPS
3
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................................6
1.1 Packet Contents ...........................................................................................................................................6
1.2 Product Description.....................................................................................................................................7
1.3 How to Use This Manual............................................................................................................................10
1.4 Product Features........................................................................................................................................11
1.5 Product Specifications ..............................................................................................................................13
2. INSTALLATION ...................................................................................................................15
2.1 Hardware Description................................................................................................................................15
2.1.1 Switch Front Panel ..............................................................................................................................................15
2.1.2 LED Indications ...................................................................................................................................................16
2.1.3 Switch Rear Panel ...............................................................................................................................................17
2.2 Installing the Switch...................................................................................................................................18
2.2.1 Desktop Installation .............................................................................................................................................18
2.2.2 Rack Mounting.....................................................................................................................................................19
2.2.3 Installing the SFP transceiver ..............................................................................................................................20
3. SWITCH MANAGEMENT....................................................................................................23
3.1 Requirements..............................................................................................................................................23
3.2 Management Access Overview.................................................................................................................24
3.3 Web Management.......................................................................................................................................24
3.4 SNMP-based Network Management.........................................................................................................25
4. WEB CONFIGURATION......................................................................................................26
4.1 Main Web Page...........................................................................................................................................28
4.2 System.........................................................................................................................................................30
4.2.1 System Information..............................................................................................................................................30
4.2.2 IP Configurations .................................................................................................................................................31
4.2.3 Password Setting.................................................................................................................................................32
4.2.4 Factory Default ....................................................................................................................................................32
4.2.5 Firmware Update .................................................................................................................................................33
4.2.6 Reboot .................................................................................................................................................................35

User’s Manual of FGSW-1816HPS
4
4.2.7 NTP Setting .........................................................................................................................................................35
4.3 Port Management .......................................................................................................................................37
4.3.1 Port Configuration................................................................................................................................................38
4.3.2 Port Mirroring.......................................................................................................................................................40
4.3.3 Bandwidth Control ...............................................................................................................................................41
4.3.4 Broadcast Storm Control......................................................................................................................................43
4.3.5 Port Statistics.......................................................................................................................................................44
4.4 VLAN............................................................................................................................................................46
4.4.1 VLAN Overview ...................................................................................................................................................46
4.4.2 VLAN Basic Information.......................................................................................................................................48
4.4.2.1 Port-based VLAN mode.............................................................................................................................48
4.4.2.2 Tag-based VLAN Mode .............................................................................................................................48
4.4.3 VLAN Port Configuration .....................................................................................................................................50
4.4.3.1 Port-based VLAN Mode.............................................................................................................................50
4.4.3.2 Tag-based VLAN Mode .............................................................................................................................51
4.4.4 Multi to 1 Setting..................................................................................................................................................52
4.5 Quality of Service.......................................................................................................................................53
4.5.1 QoS overview ......................................................................................................................................................53
4.5.2 Priority Mode .......................................................................................................................................................53
4.5.3 Class of Service Configuration ............................................................................................................................54
4.5.4 TCP/UDP Port Based QoS ..................................................................................................................................55
4.6 Security .......................................................................................................................................................57
4.6.1 MAC Address Filter..............................................................................................................................................57
4.6.2 TCP/UDP Filter ....................................................................................................................................................58
4.7 Spanning Tree.............................................................................................................................................60
4.7.1 STP Bridge Settings ............................................................................................................................................66
4.7.2 STP Port Settings ................................................................................................................................................68
4.7.3 Loopback Detection .............................................................................................................................................70
4.8 Trunking Setting.........................................................................................................................................72
4.8.1 Link Aggregation Settings ....................................................................................................................................74
4.9 DHCP Relay Agent......................................................................................................................................76
4.9.1 DHCP Relay Agent ..............................................................................................................................................76
4.9.2 DHCP Relay Server.............................................................................................................................................77
4.9.3 VLAN MAP Relay Agent ......................................................................................................................................78
4.10 PoE Setting ...............................................................................................................................................79
4.10.1 Power over Ethernet Powered Device...............................................................................................................79

User’s Manual of FGSW-1816HPS
5
4.10.2 PoE Status.........................................................................................................................................................80
4.10.3 PoE Port Setting ................................................................................................................................................81
4.10.4 Port Sequential ..................................................................................................................................................84
4.10.5 PoE Schedule....................................................................................................................................................85
4.11 Configuration Backup / Upload...............................................................................................................88
4.12 Misc Operation .........................................................................................................................................89
4.13 SNMP.........................................................................................................................................................94
4.14 Logout .......................................................................................................................................................96
5. SWITCH OPERATION.........................................................................................................97
5.1 Address Table.............................................................................................................................................97
5.2 Learning ......................................................................................................................................................97
5.3 Forwarding & Filtering...............................................................................................................................97
5.4 Store-and-Forward .....................................................................................................................................97
5.5 Auto-Negotiation ........................................................................................................................................98
6. Power over Ethernet Overview..........................................................................................99
7. TROUBLESHOOTING.......................................................................................................101
APPENDIX A .........................................................................................................................103
A.1 Switch's RJ-45 Pin Assignments ...........................................................................................................103
A.2 10/100Mbps, 10/100Base-TX...................................................................................................................103

User’s Manual of FGSW-1816HPS
6
1. INTRODUCTION
Thanks you for purchasing 16-Port 10/100Base-TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart Ethernet Switch,
FGSW-1816HPS. “PoE Web Smart Switch” mentioned in this Guide refers to the FGSW-1816HPS.
1.1 Packet Contents
Open the box of the PoE Web Smart Switch and carefully unpack it. The box should contain the following items:
The PoE Web Smart Switch x1
Quick Installation Guide x1
SFP Dust Cap x2
Rubber Feet x4
Rack Mount Accessory Kit x1
Power Cord x1
If any item is found missing or damaged, please contact your local reseller for replacement.

User’s Manual of FGSW-1816HPS
7
1.2 Product Description
Ideal Solution for Secure IP Surveillance Infrastructure
Particularly designed for the growing popular IP surveillance applications, PLANET FGSW-1816HPS 802.3at PoE web smart
switch is positioned as a surveillance switch with the central management of remote power control and IP camera monitoring.
The FGSW-1816HPS provides intelligent PoE functions along with 16 10/100Base-TX ports featuring 30-watt 802.3at PoE+
with RJ45 copper interfaces and 2 Gigabit TP/SFP combo interfaces supporting high-speed transmission of surveillance
images and videos.
Perfectly-integrated Solution for PoE IP Camera and NVR System
Being different from the general IT industry PoE switch which usually contains 12 or 24 PoE ports, the FGSW-1816HPS
provides 16 802.3at PoE+ ports for catering to medium to large scale of IP surveillance networks at a lower total cost. With its
7.2Gbps high-performance switch architecture and 220-watt PoE power budget, the recorded video files from 16 PoE IP
cameras can be powered by the FGSW-1816HPS and saved in the 8 / 16 / 32-channel NVR systems or surveillance software to
perform comprehensive security monitoring. For instance, one FGSW-1816HPS can be combined with one 16-channel NVR
and 16 PoE IP cameras as a kit for the administrators to centrally and efficiently manage the surveillance system in the local
LAN and the remote site via Internet.

User’s Manual of FGSW-1816HPS
8
Intelligent LED Indicator for Real-time PoE Usage
The FGSW-1816HPS helps users to monitor the current status of PoE power usage easily and efficiently by its advanced LED
indication. Called “PoE Power Usage”, the front panel of the FGSW-1816HPS Fast Ethernet PoE+ Switch has four orange
LEDs indicating 50W, 100W, 150W and 190W of PoE power usage.
PoE Schedule for Energy Saving
Besides being used as an IP Surveillance, the FGSW-1816HPS is certainly applicable to constructing any PoE network
including VoIP and wireless LAN. Under the trend of energy saving worldwide and contributing to environmental protection on
the Earth, the FGSW-1816HPS can effectively control the power supply besides its capability of giving high watts power. The
“PoE schedule” function is for you to enable or disable PoE power feeding for each PoE port during specified time intervals and
it is a powerful function to help SMBs or enterprises save power and money.
Robust Layer 2 Features
The FGSW-1816HPS can be programmed for advanced switch management functions such as dynamic port link aggregation
(LACP), Spanning Tree Protocol (STP), IGMP Snooping v1, v2, bandwidth control and L2/L4 security control. The
FGSW-1816HPS provides IEEE 802.1Q tagged VLAN, port-based VLAN and MTU VLAN. The VLAN groups allowed will be
maximally up to 32. Via aggregation of supporting ports, the FGSW-1816HPS allows the operation of a high-speed trunk
combining multiple ports and supports fail-over as well.

User’s Manual of FGSW-1816HPS
9
Flexible and Extendable Uplink Solution
The FGSW-1816HPS provides 2 extra Gigabit TP/SFP combo interfaces supporting 10/100/1000Base-T RJ-45 copper to
connect with surveillance network devices such as NVR, Video Streaming Server or NAS to facilitate surveillance
management. Or through these dual-speed fiber SFP slots, it can also connect with the 1000Base-SX/LX SFP (Small
Form-factor Pluggable) fiber transceiver to uplink to backbone switch and monitoring center in long distance. The distance can
be extended from 550m to 2km (multi-mode fiber), even going up to above 10/20/30/40/50/70/120km (single-mode fiber or
WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

User’s Manual of FGSW-1816HPS
10
1.3 How to Use This Manual
This User Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Switch and how to physically install the PoE Web Smart Switch.
Section 3, SWITCH MANAGEMENT
The section contains the information about the software function of the PoE Web Smart Switch.
Section 4, WEB CONFIGURATION
The section explains how to manage the PoE Web Smart Switch by Web interface.
Section 5,SWITCH OPERATION
The chapter explains how to does the switch operation of the PoE Web Smart Switch.
Section 6,Power over Ethernet Overview
The chapter introduces the IEEE 802.3af / 802.3at PoE standard and PoE provision of the PoE Web Smart Switch.
Section 7,TROUBSHOOTING
The chapter explains how to troubleshoot the PoE Web Smart Switch.
Appendix A
The section contains cable information of the PoE Web Smart Switch.

User’s Manual of FGSW-1816HPS
11
1.4 Product Features
Physical Port
16-port 10/100Base-TX RJ45 copper with PoE in-line supported
2-port 10/100/1000Base-T RJ45 copper
2 1000Base-X mini-GBIC/SFP slots to share with Port-17 to Port-18
Reset button for system management
Power over Ethernet
Complies with IEEE 802.3at High Power over Ethernet End-Span PSE
Complies with IEEE 802.3af Power over Ethernet End-Span PSE
Up to 16 IEEE 802.3at / 802.3af devices powered
Supports PoE Power up to 30.8 watts for each PoE port
Detects powered device (PD) automatically
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
PoE Power Usage (50/100/150/190 watts)
PoE Management
Per port PoE function enable/disable
PoE Port Power feeding priority
Per PoE port power limit
PD classification detection
PoE Power sequential
PoE schedule
Layer 2 Features
Auto-MDI/MDI-X detection on each RJ45 port
Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
Supports broadcast storm control
Supports VLAN:
- IEEE 802.1Q tag-based VLAN, up to 32VLANs groups, out of 4095 VLAN IDs
- Port-based VLAN, up to 16 VLAN groups
- MTU VLAN (Multi-tenant Unit VLAN)
Supports Link Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP)
- Cisco ether-channel (Static Trunk)
Supports Spanning Tree Protocol
- STP, IEEE 802.1d Spanning Tree Protocol
- RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Provides port mirror (Many-to-1)
Loopback protection to avoid broadcast loops
Quality of Service
2 priority queues on all switch ports
Traffic classification
- Port-based priority
- IEEE 802.1p-based priority
- IP TOS / DSCP-based priority

User’s Manual of FGSW-1816HPS
12
- TCP / UDP port-based QoS
Strict priority and Weighted Round Robin (WRR) CoS policies
Multicast
Supports IGMP Snooping v1 and v2
Security
Physical port to MAC address binding
TCP/UDP port number filter: Forwarding or discarding typical network applications
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Management
Switch Management Interfaces
- Web switch management
- SNMP v1 switch management
Supports DHCP Option82 and DHCP Relay
Firmware upload/download via HTTP
Network Time Protocol (NTP)
Hardware reset button for system reboot or reset to factory default
PLANET smart discovery utility

User’s Manual of FGSW-1816HPS
13
1.5 Product Specifications
Product FGSW-1816HPS
Hardware Specifications
10/100Mbps Copper Ports 16 10/100Base-TX RJ45 Auto-MDI/MDI-X ports
Gigabit Copper Ports 2 10/100/1000Base-T RJ45 Auto-MDI/MDI-X ports
SFP/mini-GBIC Slots 2 1000Base-X SFP interfaces, shared with Port-17 to Port-18
Switch Architecture Store-and-Forward
Switch Fabric 7.2Gbps / non-blocking
Throughput 5.35Mpps@64Bytes
Address Table 4K entries, automatic source address learning and ageing
Share Data Buffer 2.75Mb embedded memory for packet buffers
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Maximum Transmit Unit size
(MTU size) 1536 Bytes
Reset Button < 5 sec: System reboot
> 5 sec: Factory Default
Dimensions (W x D x H) 440 x 200 x 44.5 mm, 1U height
Weight 2.55kg
LED
System:
Power (Green)
10/100Base-TX RJ45 Interfaces (Port1 to Port16):
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
10/100/1000Base-T RJ45 / SFP Interfaces (Port17 to Port18):
LNK/ACT (Green)
100/1000 (Green)
PoE Usage
50W, 100W, 150W, 190W (Orange)
Power Requirements 100~240V AC, 50/60Hz, 4A
Power Consumption Max. 240 watts / 816 BTU
ESD Protection 2KV DC
Power over Ethernet
PoE Standard IEEE 802.3af / 802.3at PoE / PSE
PoE Power Supply Type End-span
PoE Power Output Per Port 56V DC, Max. 30.8 watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 220 watts (max.)
PD @ 7 watts 16 units PoE
Ability PD @ 15.4 watts 12 units

User’s Manual of FGSW-1816HPS
14
PD @ 30.8 watts 7 units
Layer 2 Functions
Port Configuration
Port disable / enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow Control disable / enable
Port Status Display each port’s speed duplex mode, link status, flow control status, auto
negotiation status and trunk status
Port Mirroring TX / RX / Both
Many-to-1 monitor
VLAN 802.1Q tagged-based VLAN, up to 32VLAN groups, out of 4094 VLAN IDs
Port-based VLAN, up to 18 VLAN groups
MTU VLAN
Link Aggregation 2 groups of 4-Port 10/100Base-TX trunk supported
1 group of 2-Port 10/100/1000Base-T trunk supported
QoS Allow to assign low / high priority on each port
First-In-First-Out, All-High-before-Low, Weight-Round-Robin QoS policy
IGMP Snooping IGMP (v1/v2) Snooping, up to 32 multicast groups
Security Control MAC address binding
TCP & UDP filter
Management Functions
Basic Management Interfaces Web Browser, SNMP v1
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet
IEEE 802.3x Full-duplex flow control
IEEE 802.1Q VLAN
IEEE 802.1p QoS
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Twisted-Pair 10Base-T: 2-Pair UTP CAT. 3, 4, 5, up to 100 meters
100Base-TX: 2-Pair UTP CAT. 5, 5e up to 100 meters
1000Base-T: 4-Pair UTP CAT. 5e, 6 up to 100 meters
Cable Fiber-Optic
Cable
1000Base-SX :
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
SFP module)
1000Base-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/70/120 kilometers
(varying on SFP module)
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)

User’s Manual of FGSW-1816HPS
15
2. INSTALLATION
This section describes the hardware features and installation of the PoE Web Smart Switch on the desktop or rack mount. For
easier management and control of the PoE Web Smart Switch, familiarize yourself with its display indicators, and ports. Front
panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the PoE Web Smart
Switch, please read this chapter completely.
2.1 Hardware Description
2.1.1 Switch Front Panel
The front panel provides a simple interface monitoring the PoE Web Smart Switch. Figure 2-1 shows the front panel of the
FGSW-1816HPS.
Front Panel
Figure 2-1FGSW-1816HPS front panel
■ Fast Ethernet TP interface
10/100Base-TX Copper, RJ-45 Twist-Pair: Up to 100 meters.
■ Gigabit TP Interface
Port-17, Port-18: 10/100/1000Base-T Copper, RJ-45 Twist-Pair: up to 100 meters.
■ Gigabit SFP Slots
Port-17, Port-18: 1000Base-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters
(Multi-mode fiber), up to 10/20/30/40/50/70/120 kilometers (Single-mode fiber).
■ Reset Button
On the left side of the front panel, the reset button is designed for rebooting the PoE Web Smart Switch without turning off
and on the power. The following is the summary table of Reset button functions:
Reset Button Pressed and Released Function
< 5 sec: System Reboot Reboot the PoE Web Smart Switch.
> 5 sec: Factory Default
Reset the PoE Web Smart Switch to Factory Default
configuration. The PoE Web Smart Switch will then reboot
and load the default settings as shown below:
Default Username: admin
Default Password: admin
Default IP address: 192.168.0.100
Subnet mask: 255.255.255.0
Default Gateway: 192.168.0.254

User’s Manual of FGSW-1816HPS
16
2.1.2 LED Indications
The front panel LEDs indicate instant status of port links, data activity and system power, and help monitor and troubleshoot
when needed. Figure 2-2 shows the LED indications of these PoE Web Smart Switches.
LED Indication
Figure 2-2 FGSW-1816HPS LED panel
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
Per 10/100Mbps port with PoE interfaces (Port-1 to Port-16)
LED Color Function
Lights: Indicates the link through that port is successfully established at 10/100Mbps.
LNK/ACT Green Blink: Indicates that the Switch is actively sending or receiving data over that port.
Lights: Indicates the port is providing 56V DC in-line power.
PoE In-Use Orange Off:Indicates the connected device is not a PoE Powered Device (PD).
Per 10/100/1000Mbps RJ-45 Combo Interface (Port-17 to Port-18)
LED Color Function
LNK/ACT Green Blink: Indicates that the Switch is actively sending or receiving data over that port.
Lights. Indicates the port is successfully established at 1000Mbps.
Slow
Blink:Indicates the port is successfully established at 100Mbps.
100/1000 Green
OFF:Indicates the port is successfully established at 10Mbps.
Per 1000Mbps SFP Combo Interface (Port-17 to Port-18)
LED Color Function
LNK/ACT Green Blink: Indicates that the Switch is actively sending or receiving data over that port.
1000 Green Lights. Indicates the port is successfully established at 1000Mbps.
PoE Usage
LED Color Function
50W Orange Lights to indicate the PoE power consumption has equal 50W or over 50W.
100W Orange Lights to indicate the PoE power consumption has equal 100W or over 100W.
150W Orange Lights to indicate the PoE power consumption has equal 150W or over 150W.
190W Orange Lights to indicate the PoE power consumption has equal 190W or over 190W.

User’s Manual of FGSW-1816HPS
17
2.1.3 Switch Rear Panel
The rear panel of the PoE Web Smart Switch indicates a DC inlet power socket. Figure 2-3 shows the rear panel of these PoE
Web Smart Switches
Rear Panel
Figure 2-3Rear panel of FGSW-1816HPS
■ AC Power Receptacle
For compatibility with electric service in most areas of the world, the PoE Web Smart Switch’s power supply automatically
adjusts to line power in the range of 100-240V AC and 50/60 Hz.
Plug the female end of the power cord firmly into the receptalbe on the rear panel of the PoE Web Smart Switch. Plug the
other end of the power cord into an electric service outlet and the power will be ready.
Power Notice:
The device is a power-required device, which means it will not work till it is powered. If your networks
should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime. In some areas, installing a surge
suppression device may also help to protect your PoE Web Smart Switch from being damaged by
unregulated surge or current to the Switch or the power adapter.

User’s Manual of FGSW-1816HPS
18
2.2 Installing the Switch
This section describes how to install your PoE Web Smart Switch and make connections to the PoE Web Smart Switch. Please
read the following topics and perform the procedures in the order being presented. To install your PoE Web Smart Switch on a
desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install the PoE Web Smart Switch on desktop or shelf, please follow these steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the PoE Web Smart Switch.
Step2: Place the PoE Web Smart Switch on the desktop or the shelf near a DC or PoE-in power source, as shown in Figure 2-4.
Figure 2-4 Place the PoE Web Smart Switch on the desktop
Step3: Keep enough ventilation space between the PoE Web Smart Switch and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1,
Section 4 under specifications.
Step4: Connect the PoE Web Smart Switch to network devices.
Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the front of the PoE Web Smart Switch.
Connect the other end of the cable to the network devices such as printer server, workstation or router.
Connection to the PoE Web Smart Switch requires UTP Category 5 network cabling with RJ-45 tips.
For more information, please see the Cabling Specifications in Appendix A.
Step5: Supply power to the PoE Web Smart Switch.
Connect one end of the power cable to the PoE Web Smart Switch.
Connect the power plug of the power cable to a standard wall outlet.
When the PoE Web Smart Switch receives power, the Power LED should remain solid Green.

User’s Manual of FGSW-1816HPS
19
2.2.2 Rack Mounting
To install the PoE Web Smart Switch in a 19-inch standard rack, please follow the instructions described below.
Step1: Place the PoE Web Smart Switch on a hard flat surface, with the front panel positioned towards the front side.
Step2: Attach the rack-mount bracket to each side of the PoE Web Smart Switch with supplied screws attached to the package.
Figure 2-5 shows how to attach brackets to one side of the PoE Web Smart Switch.
Figure 2-5: Attach Brackets to the PoE Web Smart Switch.
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the PoE Web Smart Switch, use suitable screws to securely attach the brackets to the
rack, as shown in Figure 2-6.
Figure 2-6: Mounting PoE Web Smart Switch in a Rack

User’s Manual of FGSW-1816HPS
20
Step6: Proceeds with the steps 4 and 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply power
to the PoE Web Smart Switch.
2.2.3 Installing the SFP transceiver
The sections describe how to insert an SFP transceiver into an SFP slot.
The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port
without having to power down the PoE Web Smart Switch, as the Figure 2-5 shows.
Figure 2-5 Plug in the SFP transceiver
Approved PLANET SFP Transceivers
PLANET PoE Web Smart Switch supports both Single mode and Multi-mode SFP transceiver. The following list of approved
PLANET SFP transceivers is correct at the time of publication:
Gigabit Ethernet Transceiver (1000Base-X SFP)
Model Speed (Mbps) Connector
Interface Fiber Mode
Distance Wavelength (nm) Operating Temp.
MGB-GT 1000 Copper -- 100m -- 0 ~ 60 ℃
MGB-SX 1000 LC Multi Mode 550m 850nm 0 ~ 60 ℃
MGB-SX2 1000 LC Multi Mode 2km 1310nm 0 ~ 60 ℃
MGB-LX 1000 LC Single Mode 10km 1310nm 0 ~ 60 ℃
MGB-L30 1000 LC Single Mode 30km 1310nm 0 ~ 60 ℃
MGB-L50 1000 LC Single Mode 50km 1550nm 0 ~ 60 ℃
MGB-L70 1000 LC Single Mode 70km 1550nm 0 ~ 60 ℃
MGB-L120 1000 LC Single Mode 120km 1550nm 0 ~ 60 ℃
MGB-TSX 1000 LC Multi Mode 550m 850nm -40 ~ 75 ℃
MGB-TLX 1000 LC Single Mode 10km 1310nm -40 ~ 75 ℃
MGB-TL30 1000 LC Single Mode 30km 1310nm -40 ~ 75 ℃
MGB-TL70 1000 LC Single Mode 70km 1550nm -40 ~ 75 ℃