Planet Networking & Communication UPOE-800G User manual

User’s Manual of UPOE-800G / UPOE-1600G
1

User’s Manual of UPOE-800G / UPOE-1600G
Trademarks
Copyright © PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose. PLANET has made every effort to ensure that this User's Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET
makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make
improvements to this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the power cable
to disconnect the device from the power circuit. In view of saving the energy and reducing the unnecessary power
consumption, it is strongly suggested to remove the power connection for the device if this device is not intended to be
active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 8-/16-Port Gigabit 60W Ultra PoE Managed Injector Hub User's Manual
FOR MODELS: UPOE-800G, UPOE-1600G
REVISION: 1.0 (JUNE, 2016)
Part No.: EM-UPOE-800G_1600G_v1.0
2

User’s Manual of UPOE-800G / UPOE-1600G
3
TABLE OF CONTENTS
1. INTRODUCTION ........................................................................................ 5
1.1 PACKAGE CONTENTS.....................................................................................................5
1.2 PRODUCT DESCRIPTION .................................................................................................6
1.3 HOW TO USE THIS MANUAL..........................................................................................11
1.4 PRODUCT FEATURES ...................................................................................................12
1.5 PRODUCT SPECIFICATIONS...........................................................................................14
2. INSTALLATION........................................................................................ 16
2.1 HARDWARE DESCRIPTION ............................................................................................16
2.1.1 Injector Front Panel ..........................................................................................16
2.1.2 LED Indicators..................................................................................................17
2.1.3 Injector Rear Panel...........................................................................................18
2.2 INSTALLING THE ULTRA POEMANAGED INJECTOR HUB .................................................19
2.2.1 Desktop Installation ..........................................................................................19
2.2.2 Rack Mounting .................................................................................................20
2.2.3 Network Application Installation........................................................................22
2.2.4 Power over Ethernet Powered Device..............................................................23
3 Management............................................................................................. 24
3.1 OVERVIEW ..................................................................................................................24
3.2 REQUIREMENTS...........................................................................................................24
3.3 MANAGEMENT METHOD ...............................................................................................25
3.3.1 Web Management ............................................................................................25
3.3.2 PLANET Smart Discovery Utility ......................................................................26
4 WEB CONFIGURATION ........................................................................... 28
4.1 MAIN MENU.................................................................................................................28
4.2 WEB PANEL................................................................................................................29
4.3 SYSTEM ......................................................................................................................29
4.3.1 System Information ..........................................................................................30
4.3.2 IP Configuration................................................................................................31
4.3.3 NTP Configuration............................................................................................32
4.3.4 Password Setting .............................................................................................33
4.3.5 Firmware Upgrade............................................................................................34
4.3.6 Configuration Setting........................................................................................35
4.3.7 Factory Default .................................................................................................37
4.3.8 System Log ......................................................................................................39
4.3.9 System Reboot.................................................................................................40

User’s Manual of UPOE-800G / UPOE-1600G
4
4.3.10 Logout ............................................................................................................41
4.4 SNMP........................................................................................................................43
4.4.1 SNMP Management .........................................................................................43
4.5 POWER OVER ETHERNET..............................................................................................45
4.5.1 PoE Configuration ............................................................................................46
4.5.2 PoE Schedule Profile........................................................................................48
4.5.3 PoE Alive Check Configuration ........................................................................52
4.5.4 PoE Status .......................................................................................................54
5. Power Over Ethernet Overview.............................................................. 55
6. The PoE Provision Process ................................................................... 57
6.1 LINE DETECTION..........................................................................................................57
6.2 CLASSIFICATION..........................................................................................................57
6.3 START-UP ...................................................................................................................58
6.4 OPERATION.................................................................................................................58
6.5 POWER DISCONNECTION SCENARIOS............................................................................58
APPENDIX A................................................................................................ 60
A.1 MDI SETTINGS............................................................................................................60
A.2 POWER DEVICE CLASSIFICATION VALUES.....................................................................60
A.3 DATA OUT POEINJECTOR RJ45 PORT PIN ASSIGNMENTS..........................................61

User’s Manual of UPOE-800G / UPOE-1600G
5
1. I NTRODUCTI ON
Thank you for purchasing PLANET 8-/16-Port Gigabit 60W Ultra PoE Managed Injector Hub, UPOE-800G/UPOE-1600G.
The description of this model is shown below:
UPOE-800G 8-Port Gigabit 60W Ultra PoE Managed Injector Hub (400 watts)
UPOE-1600G 16-Port Gigabit 60W Ultra PoE Managed Injector Hub (600 watts)
1.1 Package Contents
Open the box of the Ultra PoE Managed Injector Hub and carefully unpack it. The box should contain the following items:
The UPOE-800G or UPOE-1600G x 1
Quick Installation Guide x 1
Power Cord x 1
Rubber Feet x 4
19” Rack-mounting Brackets x 2
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
In the following section,
■ The term “Ultra PoE Managed Injector Hub”mentioned in this user’s manual refers to the
UPOE-800G/UPOE-1600G.

User’s Manual of UPOE-800G / UPOE-1600G
1.2 Product Description
PLANET Ultra PoE Managed Injector Hub series, a cost-effective and quick Ultra PoE solution, is designed to perfectly
upgrade an existing network infrastructure to Ultra Power over Ethernet network system without replacing the existing
Ethernet Switch.
Ready to Deploy Next Generation Power over Ethernet
The Ultra PoE Managed Injector Hub is a high-density, rack-mountable managed Ultra PoE Managed Injector Hub
featuring PLANET intelligent PoE functions through web user interface for remote management. It provides 8/16
10/100/1000BASE-T Ethernet ports featuring Ultra PoE injector with a total PoE budget of 400/600 watts. Each PoE port
can deliver up to 60-watt power over Cat.5/5e/6 Ethernet UTP cables which allow data and power to transmit
simultaneously to a remote 60W and 802.3at/af powered device (PD).
The Ultra PoE Managed Injector Hub enables centralization of the power supply and optimizes the installation and power
management of remote network devices, and provides a quick, safe and cost-effective Power over Ethernet network
solution for small businesses and enterprises.
Quick and Easy PoE Network Deployment
The Ultra PoE Managed Injector Hub is installed between a regular Ethernet Switch and the PDs. There are totally 16/32
RJ45 STP ports on the front panel of the Ultra PoE Managed Injector Hub, of which the 8/16 ports are on the lower stack
functioned as "Data input" while the other 8/16 ports are on the upper stack functioned as "PoE (Data and Power)
output". Both power and data are transferred simultaneously over the UTP cables to PDs without affecting the existing
network performance and functions. With data and Power over Ethernet from one unit, the Ultra PoE Managed Injector Hub
can reduce power cable deployment and eliminate the need for dedicated electrical outlets on the wall, ceiling or any
unreachable place.
802.3bt Ready -- 60 Watts of Power over 4-pair UTP System
The Ultra PoE Managed Injector Hub solution adopts the IEEE 802.3at/af PoE standard. Instead of delivering power over
2-pair twisted UTP – be it end-span (Pins 1, 2, 3 and 6) or mid-span (Pins 4, 5, 7 and 8), it provides the capability to source
up to 60 watts of power by using all the four pairs of standard Cat.5e/6 Ethernet cabling. In the new 4-pair system, the Ultra
PoE Managed Injector Hub is able to deliver per port up to 60 watts of power to each remote PoE compliant powered
6

User’s Manual of UPOE-800G / UPOE-1600G
device. It possesses double amount of power capability than the conventional 802.3at PoE and is an ideal solution to
satisfying the growing demand for higher power consuming network PDs, such as:
■PoE PTZ speed dome
■Any network device that needs higher PoE power to work normally
■Thin-client
■AIO (all-in-one) touch PC, point of sale (POS) and information kiosks
■Remote digital signage display
Friendly Web Management Interface
To efficiently manage the powered devices, the Ultra PoE Managed Injector Hub provides simple Web management
interface in which administrators can control the system and PoE functions for powered devices. It can automatically
detect the power status of each port and show messages on its Web management interface. These features also provide
users with a cost-effective way to manage the device via Internet whenever they are at work or at home.
7

User’s Manual of UPOE-800G / UPOE-1600G
Built-in Unique PoE Functions for Powered Device Management
As it is the Ultra PoE Managed Injector Hub for VoIP, wireless and surveillance networks, the Ultra PoE Managed Injector
Hub features the following special PoE management functions:
PoE schedule
PD alive check
Scheduled power recycling
UPOE, end-span or mid-span selectable in PoE power output mode
PoE usage monitoring
Over temperature protection
Intelligent Powered Device Alive Check
PLANET’s Managed PoE products adopt not only Power over Ethernet technology, but also automated PD monitoring and
real-time PoE status. The Ultra PoE Managed Injector Hub can be configured to monitor connected PD’s status in real time
via ping action through the uplinked Ethernet switch. Once the PD stops working and responding, the Ultra PoE Managed
Injector Hub will recycle the PoE port power and bring the PD back to work. It also will greatly enhance the network
reliability in that the PoE port will reset the PD power, thus reducing administrator’s management burden.
PoE Schedule for Energy Saving
Under the trend of energy saving worldwide and contributing to environmental protection on the Earth, the Ultra PoE
Managed Injector Hub can effectively control the power supply besides its capability of giving high watts power. The built-in
“PoE schedule” function helps you to enable or disable PoE power feeding for each PoE port during specified time
intervals and it is a powerful function to help SMBs or enterprises save power and money. It also increases security by
powering off PDs that should not be in use during non-business hours.
8

User’s Manual of UPOE-800G / UPOE-1600G
Advanced PoE Power Output Mode Management
To fulfill the demand of various powered devices consuming stable PoE power, the Ultra PoE Managed Injector Hub
provides three different PoE power output modes for selection.
60W UPOE PoE Power Output Mode (Pins 1, 2, 3, 6 + Pins 4, 5, 7, 8)
30W End-span PoE Power Output Mode (Pins 1, 2, 3, 6)

30W Mid-span PoE Power Output Mode (Pins 4, 5, 7, 8)
9

User’s Manual of UPOE-800G / UPOE-1600G
10
Advanced Power Management
To facilitate power management, the Ultra PoE Managed Injector Hub comes with powerful PoE management features
such as over temperature protection, usage threshold alert and auto power allocation to prevent power budget
overloading. The PoE power budget can be allocated by priorities or classification and sent alert event logs when power
usage reaches the defined threshold.
Intelligent LED Indicator for Real-time PoE Usage
The Ultra PoE Managed Injector Hub helps users to monitor the current status of PoE power usage easily and efficiently by
its advanced LED indication. The front panel of the UPOE-800G has four green LEDs indicating 100W, 200W, 300W and
400W of PoE power usage.
The front panel of the UPOE-1600G also has four green LEDs indicating 150W, 300W, 450W and 600W of PoE power
usage.
PoE Usage Monitoring
Via the power usage chart in the web management interface, the Ultra PoE Managed Injector Hub enables the
administrator to monitor the status of the power usage of the connected PDs in real time.
High Power Budget for 802.3at PoE Extension
With IEEE 802.3af/802.3at PoE output capability, the Ultra PoE Managed Injector Hub can extend much longer distance by
using PLANET PoE Extender for powering up the PoE PD which can be installed over more than 100 meters away. By
daisy-chaining multiple PLANET PoE Extenders, it offers the great flexibility of doubling, tripling or quadrupling the distance
of PoE network.