Planet Networking & Communication WDAP-802AC User manual

1200Mbps Dual Band
802.11ac Outdoor
Wireless AP
WDAP-802AC

I
Copyright
Copyright  2018 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no r epresentations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, PLANET reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a p articular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.

I
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CE Compliance Statement
This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general
public to electromagnetic fields by way of health protection. The device complies with RF
specifications when it is used at a safe distance of 20 cm from your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the
EU directive 2014/53/EU) without any limitation except for the countries mentioned below:
Country Restriction Reasons/remarks
Bulgaria None General authorization required for outdoor use and
public service
France
Outdoor use;
limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian
Federation
None Only for indoor applications
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on t he environment and human health as a r esult of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.

II
Revision
User Manual of PLANET 802.11ac Dual Band Ceiling-mount Wireless Access Point
Model: WDAP-802AC
Rev: 1.0 (October, 2018)
Part No. EM-WDAP-802AC_v1.0

III
CONTENTS
Chapter 1.Product Introduction ........................................................................................................... 1
Package Contents ............................................................................................................... 11.1
Product Description ............................................................................................................ 21.2
Product Features ................................................................................................................. 51.3
Product Specifications ....................................................................................................... 61.4
Chapter 2.Hardware Installation .......................................................................................................... 9
Product Outlook .................................................................................................................. 92.1
Chapter 3.Connecting to the AP ........................................................................................................ 11
System Requirements ...................................................................................................... 113.1
Installing the AP ................................................................................................................ 113.2
Chapter 4.Quick Installation Guide ................................................................................................... 13
Manual Network Setup -- TCP/IP Configuration ............................................................. 134.1
4.1.1 Configuring the IP Address Manually ..................................................................... 13
Starting Setup in the Web UI ............................................................................................ 174.2
Chapter 5.Configuring the AP ............................................................................................................ 18
Wizard ................................................................................................................................. 195.1
Gateway Mode ................................................................................................................... 205.2
5.2.1 WAN Settings .......................................................................................................... 21
5.2.2 Wireless .................................................................................................................. 22
Repeater Mode .................................................................................................................. 235.3
WISP Mode ......................................................................................................................... 265.4
AP Mode ............................................................................................................................. 285.5
Super WDS Mode .............................................................................................................. 305.6
Advanced ........................................................................................................................... 325.7
5.7.1 Device Status .......................................................................................................... 32
5.7.2 2.4G / 5.8G Wireless .............................................................................................. 35
5.7.3 Network ................................................................................................................... 41
5.7.4 Management ........................................................................................................... 43
Chapter 6.Quick Connection to a Wireless Network ....................................................................... 47
Windows XP (Wireless Zero Configuration) ................................................................... 476.1
Windows 7 (WLAN AutoConfig) ....................................................................................... 496.2
Mac OS X 10.x .................................................................................................................... 526.3
iPhone/iPod Touch/iPad ................................................................................................... 566.4
Appendix A: Planet Smart Discovery Utility ..................................................................................... 59

IV
Appendix B: FAQs ............................................................................................................................... 60
Q1: How to set up the AP Client Connection ........................................................................... 60
Q2: How to set up the WDS Connection .................................................................................. 65
Appendix C: Troubleshooting ............................................................................................................ 68
Appendix D: Glossary ......................................................................................................................... 70

V
FIGURE
FIGURE 2-1 WDAP-802AC FRONT SIDE................................................................................................................9
FIGURE 2-2 WDAP-802AC REAR SIDE................................................................................................................10
FIGURE 2-3 WDAP-802AC SIDE PANEL ..............................................................................................................10
FIGURE 3-1 INSTALLING BACKPLANE AND BRACKET............................................................................................12
FIGURE 3-2 CONNECTING ANTENNAS AND ETHERNET CABLE ...............................................................................12
FIGURE 4-1 TCP/IP SETTING................................................................................................................................14
FIGURE 4-2 WINDOWS START MENU ....................................................................................................................15
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .........................................................................................15
FIGURE 4-4 FAILED RESULT OF PING COMMAND ..................................................................................................16
FIGURE 4-5 LOGIN BY DEFAULT IPADDRESS........................................................................................................17
FIGURE 4-6 LOGIN WINDOW ................................................................................................................................17
FIGURE 5-1 MAIN MENU ......................................................................................................................................18
FIGURE 5-2 OPERATION MODE .............................................................................................................................19
FIGURE 5-3 GATEWAY MODE................................................................................................................................20
FIGURE 5-4 GATEWAY-STATIC IP..........................................................................................................................21
FIGURE 5-5 GATEWAY –PPPOE(ADSL)..............................................................................................................21
FIGURE 5-6 GATEWAY –DHCP.............................................................................................................................22
FIGURE 5-7 GATEWAY –WIRELESS .......................................................................................................................22
FIGURE 5-8 REPEATER MODE ...............................................................................................................................23
FIGURE 5-9 REPEATER MODE -SCAN AP..............................................................................................................24
FIGURE 5-10 REPEATER MODE -SELECT AP.........................................................................................................25
FIGURE 5-11 REPEATER MODE –CONFIGURE 5G WIRELESS ................................................................................25
FIGURE 5-12 WISPMODE....................................................................................................................................26
FIGURE 5-13 WISPMODE –SELECT AP...............................................................................................................27
FIGURE 5-14 WISPMODE –SELECT WAN TYPE..................................................................................................27
FIGURE 5-15AP MODE.........................................................................................................................................28
FIGURE 5-16 SUPER WDS MODE..........................................................................................................................30
FIGURE 5-17 SUPER WDS MODE –AP1...............................................................................................................31
FIGURE 5-18 SUPER WDS MODE –AP2...............................................................................................................31
FIGURE 5-19 ADVANCED ......................................................................................................................................32
FIGURE 5-20 STATUS ............................................................................................................................................32
FIGURE 5-21 WIRELESS STATUS ...........................................................................................................................33
FIGURE 5-22 LAN STATUS ...................................................................................................................................34
FIGURE 5-23 2.4G BASIC SETTINGS......................................................................................................................35
FIGURE 5-24 5G BASIC SETTINGS.........................................................................................................................36
FIGURE 5-25 VIRTUAL AP ....................................................................................................................................37
FIGURE 5-26ACCESS CONTROL -ACCESS ALL.....................................................................................................38
FIGURE 5-27ACCESS CONTROL –ALLOW LISTED ................................................................................................38
FIGURE 5-28ADVANCED SETTINGS ......................................................................................................................39
FIGURE 5-29 LAN SETTINGS................................................................................................................................41
FIGURE 5-30VLAN .............................................................................................................................................41
FIGURE 5-31 SNMP .............................................................................................................................................42

VI
FIGURE 5-32 SYSTEM TIME ..................................................................................................................................43
FIGURE 5-33 LOGS ...............................................................................................................................................43
FIGURE 5-34 UPGRADING FIRMWARE ...................................................................................................................44
FIGURE 5-35 SYSTEM ...........................................................................................................................................45
FIGURE 5-36 USER................................................................................................................................................46
FIGURE 6-1 SYSTEM TRAY –WIRELESS NETWORK ICON......................................................................................47
FIGURE 6-2 CHOOSING AWIRELESS NETWORK ....................................................................................................47
FIGURE 6-3 ENTERING THE NETWORK KEY..........................................................................................................48
FIGURE 6-4 CHOOSING AWIRELESS NETWORK -- CONNECTED ............................................................................48
FIGURE 6-5 NETWORK ICON.................................................................................................................................49
FIGURE 6-6 WLAN AUTOCONFIG ........................................................................................................................49
FIGURE 6-7 TYPING THE NETWORK KEY ..............................................................................................................50
FIGURE 6-8 CONNECTING TO A NETWORK ............................................................................................................50
FIGURE 6-9 CONNECTED TO A NETWORK..............................................................................................................51
FIGURE 6-10 MAC OS –NETWORK ICON..............................................................................................................52
FIGURE 6-11 HIGHLIGHTING AND SELECTING THE WIRELESS NETWORK..............................................................52
FIGURE 6-12 ENTERING THE PASSWORD...............................................................................................................53
FIGURE 6-13 CONNECTED TO THE NETWORK .......................................................................................................53
FIGURE 6-14 SYSTEM PREFERENCES ....................................................................................................................54
FIGURE 6-15 SYSTEM PREFERENCES -- NETWORK................................................................................................54
FIGURE 6-16 SELECTING THE WIRELESS NETWORK .............................................................................................55
FIGURE 6-17 IPHONE –SETTINGS ICON.................................................................................................................56
FIGURE 6-18WI-FI SETTING ................................................................................................................................56
FIGURE 6-19WI-FI SETTING –NOT CONNECTED .................................................................................................57
FIGURE 6-20TURNING ON WI-FI..........................................................................................................................57
FIGURE 6-21 IPHONE -- ENTERING THE PASSWORD...............................................................................................58
FIGURE 6-22 IPHONE -- CONNECTED TO THE NETWORK .......................................................................................58

User Manual of WDAP-802AC
-1-
Chapter 1. Product Introduction
Package Contents 1.1
Thank you for choosing PLANET WDAP-802AC Wireless AP. Please verify the contents inside the package box.
Package Contents of WDAP-802AC
WDAP-802AC Quick Guide RJ45 Waterproof Kit x1 Backplane x 1
L-type Bracket x 1 Screw Set x 1 U-bolt Kit x 2
If there is any item missing or damaged, please contact the seller immediately.

User Manual of WDAP-802AC
-2-
Product Description 1.2
Ultra High Speed and Wide Coverage
PLANET WDAP-802AC 1200Mbps Dual Band 802.11ac Outdoor Wireless AP offers a wide coverage of wireless
Internet access and ultimate wireless speed. It comes with the IP68-rated aluminum case protected from contact
with harmful dust and immersion in water. It adopts the latest IEEE 802.11ac 2T2R dual-band technology and
provides 2.4GHz and 5GHz dual radios with maximum connectivity and performance for long-range coverage.
By connecting high-gain antenna through the flexible N-type connectors, the system integrator can easily assist
customers in achieving various outdoor long-distance applications under rough weather in any harsh
environment.
Flexible, Durable and Reliable Outdoor Characteristics
To reach maximum reliability in the harsh environment, the WDAP-802AC not only comes with IP68-rated
aluminum die-cast housing, but also adopts the enterprise-level Qualcomm kernel, capable of withstanding wide
temperature ranging from -40 to 70 degrees C. Designed with the IEEE 802.3at PoE+ (Power over Ethernet)
power scheme, the WDAP-802AC can be easily installed in the areas where power outlets are not available.
Furthermore, it is also suitable to be integrated with PLANET Solar Power PoE System to offer farther wireless
service in remote areas.

User Manual of WDAP-802AC
-3-
Central Management Simplifies High-density Deployment
For wireless deployment in high-density environments such as campuses, communities, warehouses, etc., the
dual-radio design and coverage threshold make the WDAP-802AC capable of utilizing dual band to relay signal
and limit specific clients so as to provide maximum bandwidth to those authenticated users. Moreover, you can
simply install our software controller, PLANET SAPC (Smart AP Control), to deliver wireless profiles to multiple
APs simultaneously, thus making the central management simple.
Multiple SSIDs with VLAN Tagging
In the aspect of security, the WDAP-802AC supports WPA/WPA2, and the 802.1X RADIUS authentication to
secure the wireless connection. Besides, the supported IEEE 802.1Q VLAN allows multiple VLAN tags to be
mapped to multiple SSIDs to distinguish the wireless access. This makes it possible for the WDAP-802AC to
work with managed Ethernet switches to have VLANs assigned for a different access level and authority.

User Manual of WDAP-802AC
-4-
More User-friendly and Efficient
The WDAP-802AC is designed to reduce the difficulty of the outdoor configuration and optimize user experience.
With the graphical Web GUI and setup wizard assisting administrator quickly in configuring suitable operation
modes for various applications, the built-in Wi-Fi analyzer provides real-time channel utilization to prevent
channel occupation among APs. With the automatic transmission power mechanism, distance control and
scheduled reboot setting, the WDAP-802AC is easier for administrator to deploy and manage without on-site
maintenance.

User Manual of WDAP-802AC
-5-
Product Features 1.3
 Industrial Wireless LAN and LAN
 Compliant with the IEEE 802.11a/b/g/n/ac wireless technology
 802.11ac 2T2R MIMO architecture with data rate of up to 1200Mbps (300Mbps at 2.4GHz and
867Mbps at 5GHz)
 Equipped with 10/100/1000Mbps RJ45 port with auto MDI/MDI-X supported
 RF Interface Characteristics
 Built-in four N-type antenna connectors
 High output power with multiply-adjustable transmit power control
 Outdoor Environmental Characteristics
 IP68 rating, IEEE 802.3at PoE design
 Rugged protection with aluminum extrusion case and ground terminal
 Operating temperature: -40~70 degrees C
 Multiple Operation Modes and Wireless Features
 Multiple operation modes: AP, Gateway, Repeater, WDS, WISP
 WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
 Coverage threshold to limit the weak signal of clients occupying session
 Real-time Wi-Fi channel analysis chart and client limit control for better performance
 Secure Network Connection
 Full encryption supported: 64-/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X
RADIUS authentication
 Supports 802.1Q VLAN and SSID-to-VLAN mapping
 Supports IP/Port/MAC address/URL filtering, DoS, SPI Firewall
 Supports DMZ and Port forwarding
 Bandwidth control per IP address to increase network stability
 Easy Deployment and Management
 Supports PLANET AP Controllers in AP mode
 Easy discovery by PLANET Smart Discovery
 Self-healing mechanism through system auto reboot setting
 System status monitoring through remote Syslog Server
 Supports PLANET DDNS/ Easy DDNS

User Manual of WDAP-802AC
-6-
Product Specifications 1.4
Product WDAP-802AC
1200Mbps Dual Band 802.11ac Outdoor Wireless AP
Hardware
Standard Support
IEEE 802.11ac
IEEE 802.11n
IEEE 802.11a
IEEE 802.11b
IEEE 802.11g
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x flow control
Material
Aluminum
Dimensions (W x D x H) 225 x 101.5 x 225 mm
Weight 4kg
Power Requirement 48V 0.5A, IEEE 802.3at PoE+
Power Consumption (max.) < 25.5W
Mounting Type Mast mounting
Interface Wireless IEEE802.11a/b/g/n/ac, 2T2R
PoE LAN: 1 x 10/100/1000BASE-T, auto-MDI/MDIX, 802.3at PoE In
Button Reset button (Inside enclosure)
Antenna Built-in four N-type connectors
Data Rate
IEEE 802.11b: up to 11Mbps
IEEE 802.11a/g: up to 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbps
802.11ac (VHT20): Up to 173.3Mbps
802.11ac (VHT40): Up to 400Mbps
802.11ac (VHT80): Up to 867Mbps
Media Access Control CSMA/CA
Modulation
802.11ac: OFDM (BPSK/ QPSK/ 16QAM/ 64QAM/ 256QAM)
802.11a/g/n: OFDM (BPSK/ QPSK/ 16QAM/ 64QAM)
802.11b: DSSS (DBPSK/ DQPSK/ CCK)
Frequency Band
2.4GHz :
FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz
5GHz :
FCC: 5.180~5.240GHz, 5.745~5.825GHz
ETSI: 5.180~5.700GHz

User Manual of WDAP-802AC
-7-
Operating Channels
2.4GHz :
FCC: 1~11 Channels
ETSI: 1~13 Channels
5GHz :
FCC: 36, 40, 44, 48, 149, 153, 157, 161, 165 (9 Channels)
ETSI: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136,
140 (16 Channels)
5GHz channel list will vary in different countries according to
their regulations.
Max. Transmit Power (dBm) FCC : up to 29 ± 1dBm
ETSI : < 20dBm (EIRP)
Receiver Sensitivity
(dBm)
Network Mode Data Rate Receive Sensitivity (dBm)
2.4GHz
802.11b 1Mbps -99
11Mbps -92
802.11g 6Mbps -95
54Mbps -82
802.11n HT20 MCS0/MCS8 -95
MCS7/MCS15 -77
802.11n HT40 MCS0/MCS8 -93
MCS7/MCS15 -75
5GHz
802.11a 6Mbps -92
54Mbps -75
802.11n HT20 MCS0/MCS8 -91
MCS7/MCS15 -72
802.11n HT40 MCS0/MCS8 -88
MCS7/MCS15 -70
802.11ac VHT20 MCS0 -92
MCS8 -70
802.11ac VHT40 MCS0 -89
MCS9 -65
802.11ac VHT80 MCS0 -87
MCS9 -61
Environment & Certification
Operating Temperature -40~70 degrees C
Operating Humidity 10~90% (non-condensing)
IP Level IP68
ESD Protection ±8kV air-gap discharge
±4kV contact discharge

User Manual of WDAP-802AC
-8-
Surge Protection ±4kV
Regulatory CE, RoHS
Software
LAN Static IP
Supports IP-MAC binding
WAN Type (GW/WISP mode)
 Static IP
 Dynamic IP
 PPPoE
Wireless Modes
 Access Point
 Gateway
 Repeater
 WDS
 WISP
Channel Width 20MHz, 40MHz, 80MHz
Encryption Type 64-/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security
Enable/Disable SSID Broadcast
Wireless MAC address filtering
User Isolation
Max. SSIDs 4
Max. Wireless Clients 64 per radio (50 is suggested, depending on usage)
Max. WDS Peers 4
Wireless QoS Supports Wi-Fi Multimedia (WMM)
Wireless Advanced
Auto Channel Selection
5-level Transmit Power Control (100%, 75%, 50%, 25%, 12.5%)
Client Limit Control, Coverage Threshold
Distance control (Auto Ack Timeout)
Wi-Fi channel analysis chart
Status Monitoring
Device status, Wireless client List
PLANET Smart Discovery
DHCP client table
System Log supports remote syslog server
VLAN IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping up to 4 SSIDs
Self-healing Supports auto reboot settings per day or hour
Management
Supports PLANET Hardware AP Controller/ Software AP Controller
Applicable controllers: WAPC-500/WAPC1000 and SAPC
Remote management through PLANET DDNS/ Easy DDNS
Configuration backup and restore
Supports UPnP and IGMP Proxy
Supports PPTP/L2TP/IPSec VPN Pass-through
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Fast Roaming

User Manual of WDAP-802AC
-9-
Chapter 2. Hardware Installation
Product Outlook 2.1
WDAP-802AC
 Dimensions: 225 x 101.5 x 225 mm (W x D x H)
 Weight: 4kg
 Triple View
Figure 2-1 WDAP-802AC Front Side

User Manual of WDAP-802AC
-10-
 Rear Panel
Figure 2-2 WDAP-802AC Rear Side
 Side Panel
Figure 2-3 WDAP-802AC Side Panel
Hardware Interface
Object Description
Antenna Connectors 4 N-type (female) antenna connectors
PoE LAN Port
10/100/1000Mbps RJ45 port, auto MDI/MDI-X
802.3at PoE+ supported, 48VDC In
Grounding Terminal The grounding wire must be attached to this port to prevent damage to
the AP from direct lightning strike.

User Manual of WDAP-802AC
-11-
Chapter 3. Connecting to the AP
System Requirements 3.1
 Broadband Internet Access Service (Cable/xDSL/Ethernet connection)
 One IEEE 802.3at PoE switch (supply power to the WDAP-802AC)
 PCs with a working Ethernet adapter and an Ethernet cable with RJ45 connectors
 PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux,
UNIX or other platforms compatible with TCP/IP protocols
1. The AP in the following instructions refers to PLANET WDAP-802AC.
2. It is recommended to use Internet Explorer 11, Firefox or Chrome to access the AP.
Installing the AP 3.2
Before installing the AP, make sure your PoE switch is connected to the Internet through the broadband service
successfully at this moment. If there is any problem, please contact your local I S P. After that, please install the
AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.

User Manual of WDAP-802AC
-12-
Step 1. (1) Install the Backplane to the back of the AP.
(2) Attach the L-type bracket to it.
(3) Assemble the AP to the pole by using the U-bolt kit.
※ The AP can be mounted on an up to 2.5” (O.D.) pole.
Figure 3-1 Installing Backplane and Bracket
Step 2. (1) Attach the surge arrestors to each antenna connector.
(2) Attach the antenna equipped with N-type (M) connector to each surge arrestor. Otherwise, connect
the antenna through the N-male (male pin) to N-male (male pin) cable.
(3) Plug the RJ45 Ethernet cable into the PoE port of the AP through the waterproof kit, and plug the
other side of the RJ45 cable into the PoE port of the PoE switch to finish the installation.
※ Please remember to finish grounding by consulting the local electrical experts.
Figure 3-2 Connecting Antennas and Ethernet Cable