Planet HZS-300E User manual

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Copyright
Copyright ©2015 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the
software. Further, PLANET reserves the right to revise this publication and to make changes from time to
time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered
trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna
shall not be less than 20 cm (8 inches) during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment.All guidelines of this and of the computer manufacture must therefore be allowed at all
times to ensure the safe use of the equipment.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
- 2-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s Manual of PLANET Z-Wave Ceiling-mount Smoke Detector
Model: HZS-300
Rev: 1.00 (October, 2015)
Part No. EM-HZS-300 Series_v1.0.doc
- 3-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Table of Contents
Chapter 1.Product Introduction......................................................................5
1.1 Package Contents ..............................................................................5
1.2 Overview.............................................................................................5
1.3 Specifications......................................................................................7
Chapter 2.Hardware Interface........................................................................8
Chapter 3.Z-Wave Device Setting ...............................................................10
3.1 Configuring Z-Wave Device via HAC-1000.......................................10
3.2 Configuring Z-Wave via Smart Phone...............................................14
3.3 Configuring Z-Wave via HTS-1000P.................................................23
Appendix A:Troubleshooting & Frequently Asked Questions.......................31
- 4-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 1. Product Introduction
1.1 Package Contents
The package should contain the following:
z4-in-1 Sensor x 1
zQuick Installation Guide x 1
zAAA Battery x 2
zAccessory Bag x 1
If any of the above items are missing, please contact your seller immediately.
1.2 Overview
Home Automation and Smart Home Control
The HZS (Z-Wave Sensing Device) series of PLANET Home Automation product family, based on Z-Wave
technology, provides the advanced security system that protects your home and family 24/7. Easy operation
and flexible configuration are the attractive features of our system; the simple one-touch button lets you
program your regular settings according to your preference and operation mode. Worked with PLANET
HAC-1000 Z-Wave Home Automation Control Gateway, you get the all-round and reliable home security
services that we offer. Our full range of product lines ensure that you get all the devices you need for your
home security system.
Safeguarding Homes Conveniently via the Multi-functional Sensor
PLANET HZS-300, a Z-Wave 4-in-1 Multi Sensor, has four sensors integrated into one device, thus enabling
you to monitor the security of doors and windows, humidifiers, lightings, and thermostats of your home at site
or remotely. The HZS-300 sends Z-Wave signal to the user when someone is prying a door or window open,
- 5-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
or there is a change in humidity, luminosity and temperature. It not only helps to protect homes, offices and
other establishments from theft, but also helps to keep humidity, luminosity and temperature in these places
within their ideal range.
Mini Design for Easy Installation
As the HZS-300 Z-Wave sensor comes in lightweight and compact size, it can be installed on any door and
window in less than 60 seconds. It is also hardly visible to intruders as its size is miniature.
- 6-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Getting Started is as Easy as 1-2-3
1. Via the Cloud HomeApp (including HomeAutomation Controller Pad and Control Gateway): Press
Inclusion/Exclusion to include/exclude Z-Wave device.
2. On the Z-Wave device: Press the Pair button to establish a connection with the control gateway.
3. Users can enjoy and manage Z-Wave network right away.
1.3 Specifications
Product HZS-300A HZS-300E
Feature Specifications
Z-Wave Frequency America: 908.42MHz Europe: 868.42MHz
Sensor
Door and window
Illumination
Temperature
Humidity
Temperature Detection Range -40 ~ 105° C
Illumination Range Photoresistor, 0V~1.148V (0%~100%)
Humidity Range 0%~100%
LED Indicators Opening/Closing the door/window Tamper switch
Temperature change
Operating Range Up to 30 meters in open space
Installation Wall mount, indoor use only
Hardware Specifications
Power Requirements AAAbattery, 1.5V
Operating Temperature -15 ~ 60 degrees C
Operating Humidity 0 ~ 95% (non-condensing)
Weight 40g
Dimensions (W x D x H) 69 x 28 x 19 mm
Emission CE, FCC
- 7-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 2. Hardware Interface
Model HZS-300E/HZS-300A
Dimensions (W x D x H) 69 x 28 x 19 mm
Weight 40g (gross weight)
¾Front Panel
LED/Test/Program Switch
LED
Sensor
Interface Description
LED
Opening/Closing the door/window
Tamper switch
Temperature changed
Temperature LED Color
Under 15°C Green
15~23°C Blue
23~28°C Yellow
28~36°C Orange
Over 36°C Red
*For more details on indicator, please refer to HZS-300 user manual.*
Sensor The sensor is for illumination detection.
- 8-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
¾Bottom
Program Switch
- 9-

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 3. Z-Wave Device Setting
3.1 Configuring Z-Wave Device via HAC-1000
Please refer to the following steps to add Z-Wave device via HAC-1000 web.
1. The default username and password are both admin.
2. Click Z-Wave.
3. Click Z-Wave.
- 10 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
4. Click Device Configuration.
Step 1. Include a Z-Wave device via web.
a) Go to "Z-Wave" and click "Device
Configuration".
b) Click” Include New Device” and the
screen will appear with "Add Device:
Waiting for a user action."
c) The distance between HZS-300 and
HAC-1000 is suggested to be in one
meter. Press the program switch of
HZS-300 at least for 1 second to be
included.
d) If your device has successfully been added, it will show "Add Device: Command has
been completed successfully".
If the device didn’t add successfully, please place the device next to the
gateway and try again.
- 11 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 2. Set up the location and room for Z-Wave device via HAC-1000 web.
a. Create rooms in your environment.
b. Edit device.
Step 3. Create a scene via web.
a. Click “Create Scene” and name new scene.
- 12 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
b. Select a device from this scene.
c. Select ON or OFF from this scene.
d. You can click “RUN” to run this scene.
- 13 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 4. Create trigger via web.
a. Click “Create a Trigger” and name new
trigger.
b. Select a Z-Wave device for this trigger.
c. Select when it triggers, it will alarm or
bypass.
d. Select when it triggers, it will run which
scene.
After entering the time selected for the scene to trigger, tick “Save and send alarm
notification”. Tick “Active” to enable this trigger.
3.2 Configuring Z-Wave via Smart Phone
The HAC-1100 can be used on iOS andAndroid operating system. Cloud Home can be downloaded at
Google Play store or app store.
Please refer to the following steps to install Cloud Home app and add Z-Wave device via smart phone.
- 14 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 1. Include a Z-Wave device via smart phone (Android/iOS).
a. Register a user account. b. Setting
c. Inclusion/Exclusion d. Click Inclusion to add device.
- 15 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. The distance between HZS-300 and
HAC-1000 is suggested to be in one
meter. Press the program switch 3
times within 3 seconds to be
included.
- 16 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 2. Set up the location and room for Z-Wave device.
a. Create rooms in your environment. b. Click “No Room” to show the device.
And place the new device in a room.
c. Select “Name” to name this device
and select “Location” to place this
device in the room that you created.
d. Select Picture for your Z-Wave
device.
- 17 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. Click “Back” to save. f. Done successfully.
- 18 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 3. Create a scene via smart phone.
a. Click “Add” and name a new scene.
b. Click “Add” to add a Z-Wave device.
c. Select a Z-Wave device.
d. Click ON or OFF for the device you
select.
- 19 -

Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. Click “Back” to save.
f. Done successfully.
- 20 -