Planet VIP-156 User manual

VIP-156/VIP-157
SIP Analog Telephone Adapter
Quick Start Guide

PLANET VIP-156/VIP-157 Quick Installation Guide
Overview
This quick installation guide describes the
objectives; organization and basic installation of
the PLANET VIP-156/VIP-157 VoIP Phone Adapter (“ATA”
in the following term), and explains how to establish
your first voice over IP communication via PLANET
product. Also, this guide shows you how to find
additional information on related products and
services.
Respective model/descriptions are shown below:
VIP-156: SIP Analog Telephone Adapter
VIP-156PE: 802.3af PoE SIP Analog Telephone Adapter
VIP-157: 1 FXS/ 1 FXO SIP Analog Telephone Adapter
VIP-157S: 2-port FXS SIP Analog Telephone Adapter
The VIP-156/VIP-157 series ATA integrates a
web-based graphical user interface that can cover
most configurations and machine status monitoring.
Via standard web browser, you can configure and check
machine status from anywhere around the world.
2

PLANET VIP-156/VIP-157 Quick Installation Guide
PREPARATION BEFORE BEGINNING
ADMINISTRATION ON SIPANALOG TELEPHONE
ADAPTER............................................................................ 4
PREPARATION BEFORE BEGINNING
ADMINISTRATION ON SIPANALOG TELEPHONE
ADAPTER............................................................................ 5
PHYSICAL INTERFACES ....................................................... 5
ADMINISTRATION INTERFACE ............................................. 5
Web configuration access:............................................. 6
Network Interface quick configurations........................ 7
Keypad configurations................................................... 9
VOICE COMMUNICATION SAMPLES....................... 12
ATA TOATA CONNECTION VIA IPADDRESS....................... 12
Operation steps: .......................................................... 12
(PEER-TO-PEER MODE)VIP-157S PORT 1TO PORT 2
COMMUNICATIONS ............................................................ 13
Operation steps: .......................................................... 13
VOICE COMMUNICATION VIA SIPPROXY SERVER –SIP-5015
Device configurations on the ATA:.............................. 15
VOICE COMMUNICATION VIA IPPBX SYSTEM –IPX-2000
(AUTO-CONFIG)................................................................ 17
Device configurations on the IPX-2000:..................... 17
QUICK REFERENCE IN CD-ROM GUIDE ................ 22
3

PLANET VIP-156/VIP-157 Quick Installation Guide
Document Objectives
This guide provides physical installation, network configurations,
and Internet access establishment information for theATA VoIP
Analog Phone Adapter.
Document Organization
This guide is organized as follows:
•Preparation before beginning VIP-156/VIP-157 administration
•Administration interface
•Network interface quick configurations
•Internet access setup guide
4

PLANET VIP-156/VIP-157 Quick Installation Guide
Preparation before beginning administration on
SIP Analog Telephone Adapter
Physical Interfaces
1 PC
RJ-45 connector, to maintain the existing network
structure, connected directly to the PC through
straight CAT-5 cable
2 LAN
RJ-45 connector, for Internet access, connected
directly to Switch/Hub through straight CAT-5
cable.
3 12V DC 12V DC Power input outlet
1. Use proper AC adapter for the ATA,
improper power supply will damage device
permanently.
2. For VIP-156PE, please connect IEEE802.3af
standard compliant power injector onto
the LAN interface for power resource. At
the same time, either PoE or AC adapter
can be deployed at one time.
ÍNote
Administration Interface
The ATA provides GUI (Web based, Graphical User Interface) for
machine management and. keypad administration is also available
for simple configuration.
5

PLANET VIP-156/VIP-157 Quick Installation Guide
Web configuration access:
To start ATA web configuration, you must have one of these web
browsers installed on computer for management
•Microsoft Internet Explorer 4.01 or higher with Java
support
Default IP address of ATA is 192.168.0.1. Please execute web
browser, and insert http://192.168.0.1 in the address bar of your
web browser to logonATA web configuration page.
VIP-156/VIP-157 will prompt for logon username/password, please
enter: root / null (no password) to continue machine
administration.
6

PLANET VIP-156/VIP-157 Quick Installation Guide
In order to connect machine for
administration, please locate your PC in the
same network segment (192.168.0.x) of the
ATA. If you’re not familiar with TCP/IP,
please refer to related chapter on user’s
manual CD or consult your network
administrator for proper network
configurations.
ÍNote
Network Interface quick configurations
Execute your web browser, and insert the IP address (default:
192.168.0.1) of VIP in the adddress bar.After logging on machine
with username/password (default: root / no password), browse to
“Network” --> “Network settings” configuration menu:
7

PLANET VIP-156/VIP-157 Quick Installation Guide
Parameter Description
IP address LAN IP address of
the ATA Default: 192.168.0.1
Mask LAN mask of the
ATA Default: 255.255.255.0
Default
Gateway Gateway of the ATA Default: 192.168.0.254
DNS The Domain Name
Server IP address Default: 168.95.192.1
Connection Type Data required.
Fixed IP The ISP will assign IPAddress, and related
information.
DHCP client In most circumstances, it is no need to
configure the DHCP settings.
PPPoE The ISP will assign PPPoE username /
password for Internet access.
After confirming the modification you’ve done, please click on the
Submit button to apply settings and browse to “Save & Reboot”
menu to reboot machine to make the settings effective.
Save Change to Flash Memory
Most of the modification on ATA will take effective after
modifications, but it is just temporary stored on RAM only, it will
disappear after your reboot or power off the VoIP PhoneAdapter, to
save the parameters into Flash ROM and let it take effective forever,
please remember to press the Save & Reboot button after you
modify the parameters.
8

PLANET VIP-156/VIP-157 Quick Installation Guide
Keypad configurations
The ATA series phone adapters support telephone keypad
configurations, please connect analog telephone set and refer to
the following table for machine network configurations.
Menu Choice Machine
operation
Parameter(s) Notes:
#111# Set DHCP client None ATA will change to
DHCP Client
#112xxx*xx
x*xxx*xxx#
Setup Static IP
Address
Use the * (star)
key when
entering a
decimal point.
DHCP will be
disabled and
system will change
to the Static IP type.
#113xxx*xx
x*xxx*xxx#
Set Network
Mask
Use the * (star)
key when
entering a
decimal point.
Must set Static IP
first.
#114xxx*xx
x*xxx*xxx#
Set Gateway IP
Address
Use the * (star)
key when
entering a
decimal point.
Must set Static IP
first.
#115xxx*xx
x*xxx*xxx#
Set Primary DNS
Server
Use the * (star)
key when
entering a
decimal point.
Must set Static IP
first.
9

PLANET VIP-156/VIP-157 Quick Installation Guide
#136# Enable
auto-config mode None For PLANET IPX-2000 IP PBX
#137# Disable
auto-config mode None For PLANET IPX-2000 IP PBX
#190# Unlock None
Must unlock the
protect function
before set up
network settings via
keypad.
#191# Lock None
The system will be
locked and can’t set
up network settings
via keypad.
#195# Reboot None
The system will
reboot
automatically.
#198# Factory Reset None
The system will be
reset to factory
default value and
reboot
automatically.
0＊To switch PSTN
mode None VIP-157 only
10

PLANET VIP-156/VIP-157 Quick Installation Guide
Following keypad commands can be used to display the network
settings enabled onATA via voice prompt.
IVR Menu
Choice
Machine
operation
Notes:
#120# Check IP Address IVR will announce the current IP
address of the ATA.
#121# Check network
connection Type
IVR will announce if DHCP in
enabled or disabled.
#122# Check the Phone
Number
IVR will announce current enabled
VoIP number.
#123# Check Network
Mask
IVR will announce the current
network mask of the ATA.
#124# Check Gateway IP
Address
IVR will announce the current
gateway IP address of the ATA.
#125# Check Primary
DNS Server Setting
IVR will announce the current
setting in the Primary DNS field.
#128# Check Firmware
Version
IVR will announce the version of the
firmware running on the ATA.
Please contact your Internet
service provider to obtain the
Internet access type, and select
the proper network settings in ATA
to establish the network
connections.
LHint
11

PLANET VIP-156/VIP-157 Quick Installation Guide
Voice communication samples
There are several ways to make calls to desired destination in ATA.
In this section, we’ll lead you step by step to establish your first
voice communication via keypad and web browsers operations.
ATA to ATA connection via IP address
Assume there are twoATAs in the network the IP address are
192.168.0.1, 192.168.0.2
Analog telephone sets are connected to the phone (RJ-11) port of
ATAs respectively
192.168.0.1 192.168.0.2
2*9 2 168 * 0 * 1 #
Operation steps:
1. Pick up the telephone set onATA A.
2. Press the keypad: 192*168*0*2# shall be able to connect to the
ATA B.
12

PLANET VIP-156/VIP-157 Quick Installation Guide
3. Then the phone in 192.168.0.2 should ring. Please repeat the
same dialing steps on ATA Bto establish the first voice
communication from ATA A
(Peer-to-Peer mode) VIP-157S Port 1 to Port 2
communications
Supposing you have one VIP-157S connects to two telephones,
just pick up phone 1 and dial ‘192*168*0*1**5062’, phone 2 will
ring.
Analog telephone sets are connected to the phone (RJ-11) ports of
VIP-157S respectively
1001 1002
192.168.0.1
9 2 * 1 6 8 * 0 * 1 * * 5 0 6 #2 1
Operation steps:
a) Pick up the telephone set on VIP-157S port 1, and you should be
able to hear the dial-tone
b) Press the keypad: 192*168*0*1**5062# shall be able to
connect to the VIP-157S port 2
13

PLANET VIP-156/VIP-157 Quick Installation Guide
c) Then the telephone set in VIP-157S port 2 should ring. Please
repeat the same dialing steps on port 2 to establish the first voice
communication from VIP-157S
yIn default machine operation, the
VIP-157 is VoIP mode. If you want to
make a PSTN phone call, press the “0*”
key to switch to PSTN mode.
yIf the IP address of the remote calling
party is known, you may directly make
calls via its IP address and end with
a “#”.
yIf the ATAs are installed behind a
NAT/firewall/IP sharing device for
Peer-to-Peer VoIP application, please
make sure the NAT device support SIP
applications, and suitable settings
should be applied to the NAT device to
enable the SIP communications before
making calls
y[VIP-157S] in PLANET ATA series
products, to connect to remote ATA,
press the keypad in the following
sequence to connect to the remote
VIP-157S port 2:
[remote ATA IP address]**5062,
for example:192*168*0*2**5062
LHint
14

PLANET VIP-156/VIP-157 Quick Installation Guide
Voice communication via SIP proxy server –
SIP-50
VIP-156 IPAddress:
192.168.0.1
Line Number: 1001
VIP-156 IPAddress:
192.168.0.2
Line Number: 2002
Registration /
Authenticatio
n
Registration /
Authentication
SIP-50 IP Address:
192.168.0.50
Device configurations on the ATA:
STEP 1:
Log in SIP-50 and create two testing
accounts/password: 1001/123 (for ATA A), and 1002/123
(for ATA B) for the voice calls.
STEP 2:
Please log inATA via web browser, browse to the SIP
setting menu and select the Domain Service config
menu. In the setting page, please insert the
account/password information obtained from your
service provider (in this sample, we’re using PLANET
SIP-50 as the SIP Proxy server for SIP account, call
authentications), and then the sample configuration
screen is shown below:
15

PLANET VIP-156/VIP-157 Quick Installation Guide
STEP 3:
Repeat the same configuration steps onATA B, and
check the machine registration status, make sure the
registrations are completed.
Test the scenario:
To verify the VoIP communication, please
1. Pick up the telephone onATA A
2. Press the keypad: 2002 shall be able to connect to the ATA B
3. Then the telephone set in ATA Bshould ring. Please repeat the
same dialing steps on ATA Bto establish the first voice
communication from ATA A
16

PLANET VIP-156/VIP-157 Quick Installation Guide
Voice communication via IP PBX system –
IPX-2000 (Auto-config)
In the following sample, we’ll introduce how to integrate the ATA
with our IP PBX system IPX-2000 viaAuto-config feature.
Registration /
Authentication Registration /
Authentication
VIP-156 IPAddress:
192.168.0.1
Line Number: 1001
VIP-156 IPAddress:
192.168.0.2
Line Number: 2002
IPX-2000 LAN IPAddress:
192.168.0.50
Device configurations on the IPX-2000:
STEP 1:
Log in IPX-2000 and browse to the Srevice ÆDHCP
Service menu and create new options list for the auto
configuration.
17

PLANET VIP-156/VIP-157 Quick Installation Guide
.
Code: please insert 151 as the DHCP server option.
Value: http://LAN IP for IPX-2000/tftpboot/
An example option 151 would be option=151 value=
http://192.168.0.50/tftpboot/http://192.168.0.50/tftpboot/
STEP 2:
Please browse to the Device ÆIP Phone menu and
create new device. And press the EDIT button for set up
the Auto Config configuration.
STEP 3:
Please fill out the Vendor Prefix code and MACAddress
of ATA.
18

PLANET VIP-156/VIP-157 Quick Installation Guide
LNote:
The following are the Vendor Prefix of devices:
1. VIP-156: pla156
2. VIP-157/VIP-157S: pla157
STEP 4:
Please browse to the Device ÆExtension of IP Phone
menu to create the two extension accounts/password:
1001/123 (for ATA A), and 1002/123(for ATA B) for the
voice calls.
19

PLANET VIP-156/VIP-157 Quick Installation Guide
STEP 5:
After setting up the parameters, please browse to the
Service ÆIP PBX service menu and press RELOAD
of IP PBX configuration reload selection for activating
the settings.
20