Planet FGSW-2402VS User manual

Trademarks
Copyright © PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information
in this User’s Manual, and reserves the right to make improvements to this
User’s Manual and/or to the products described in this User’s Manual, at any
time without notice.
If you nd information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Revision
PLANET 24-port 10/100Mbps+ 2-Gigabit Web Smart Ethernet Switch User’s
Manual
FOR MODEL: FGSW-2402VS / FGSW-2620VS / FGSW-2620VSF
Rev: 2.0 (November. 2004)
Part No.: 2010-000031-002

1
Table of Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 How to Use This Manual 1
1.3 Product Features 2
1.4 Product Specifications 3
Chapter 2 Installation 5
2.1 Product Description 5
2.2 Installing a FGSW-2402VS/FGSW-2620VS/FGSW-2620VSF 7
Chapter 3 Console Configuration 11
3.1 Preparing for configuration 11
3.2 Getting Started 13
Chapter 4 Web Configuration 37
4.1 Login in to the Switch 37
4.2 Main Menu 37
4.3 Port Status 39
4.4 Port Configuration 39
4.5 Trunk Configuration 40
4.6 VLAN Configuration 40
4.7 Port Mirroring Configuration 42
4.8 QoS Configuration 43
4.9 Bandwidth Control 45
4.10 Misc Configuration 46
4.11 Logout 52
Chapter 5 Switch Operation 53
5.1 Address Table 53
5.2 Learning 53
5.3 Forwarding & Filtering 53
5.4 Store-and-Forward 53
5.5 Auto-Negotiation 54
Chapter 6 Troubleshooting 55
Appendix 57
A.1 Switch‘s RJ-45 Pin Assignments 57
A.2 10/100Mbps, 10/100Base-TX 57

1
Chapter 1
Introduction
1.1 Package Contents
Check the contents of your package for following parts:
● 24-port 10/100Mbps + 2-Gigabit Web smart Ethernet Switch x1
● User’s manual x1
● RS-232 cable x1
● Power cord x1
● Two Rack-Mounting Brackets with Attachment Screws x1
If any of these are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need return to it to us for repairing.
1.2 How to Use This Manual
This 24-port 10/100Mbps +2-Gigabit Web Smart Ethernet Switch User’s Manual is
structured as follows:
● Section 2, Installation
It explains the functions of FGSW-2402VS / FGSW-2620VS / FGSW-2620VSF
and how to physically install the FGSW-2402VS / FGSW-2620VS / FGSW-
2620VSF.
● Section 3, Console Configuration
It contains information about the smart function from the console interface of
FGSW-2402VS / FGSW-2620VS / FGSW-2620VSF.
● Section 4, Web Configuration
It contains information about the smart function from the Web interface of
FGSW-2402VS / FGSW-2620VS / FGSW-2620VSF.
● Section 5 Switch operation
It explains the Switch operation of FGSW-2402VS / FGSW-2620VS / FGSW-
2620VSF.
● Section 6 Troubleshooting
It contains troubleshooting guide of FGSW-2402VS / FGSW-2620VS / FGSW-
2620VSF.
● Appendix A

2
3
It contains cable information of FGSW-2402VS / FGSW-2620VS / FGSW-
2620VSF.
In the following section, the term Switch means the Switches mentioned titled in the
cover page of the user manual, i.e. FGSW-2402VS, FGSW-2620VS and FGSW-2620VSF;
term of switch can be any third part switches.
1.3 Product Features
● Complies with the IEEE802.3, IEEE802.3u, IEEE802.3z and IEEE802.3ab Giga-
bit Ethernet standard
● 24-port 10/100Mbps Fast Ethernet Switch
● Each Switching ports support auto-negotiation-10/20, 100/200Mbps sup-
ported
● 2 open slots for 10/100Base-TX, 1000Base-T and 100Base-FX, 1000Base-SX/
LX fiber-optic interface with various connection media and distances (FGSW-
2402VS only)
● 2 10/100/1000Mbps ports (FGSW-2620VS only)
● 2 10/100/1000Mbps ports and 2 SFP interfaces (FGSW-2620VSF only)
● Auto-MDI/MDI-X detection on each RJ-45 port
● Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame
flow control (full-duplex)
● High performance Store and Forward architecture, broadcast storm control,
runt/CRC filtering eliminates erroneous packets to optimize the network band-
width
● 6K MAC address table, automatic source address learning and ageing
● 4 Mbit embedded memory for packet buffers
● Console and Web interface for Switch basic management and setup
● Support up to 26 port-based VLAN groups
● Support up to 7 Trunk groups, each trunk for up to maximum 4 port with
800Mbps bandwidth
● Port mirroring allows monitoring of the traffic across any port in real time
● Support QoS and bandwidth control on each port
● Misc Configuration for Switch advanced configuration

2
3
1.4 Product Specications
Model FGSW-2402VS / FGSW-2620VS / FGSW-2620VSF
Hardware Specification
Network ports 24 10/100Base-TX RJ-45 MDI/MDI-X ports
Module slot
(FGSW-2402VS only)
2 open slots for 10/100Base- TX, 1000Base-T and
100Base-FX, 1000Base-SX/LX fiber-optic interface
Gigabit ports
(FGSW-2620VS only) 2 10/100/1000Mbps ports
Gigabit ports (FGSW-
2620VSF only) 2 10/100/100Mbps ports and 2 SFP interfaces
Console port 1 RS-232 DB-9 male
Dimensions 440 x 200 x 44 mm (1U height)
Weight 2.6 kg
Power Requirement 100~240 (±10%) VAC, 50-60 (±3) Hz
Power Consumption 30 Watts maximum / 102 BTU/hr maximum
Switch Specification
Switch architecture Store-and-forward
Address Table 6K entries, auto learning/ageing
Shared data Buffer 4 Mbit embedded memory for packet buffers
Flow Control Back pressure for half duplex, IEEE 802.3x for full-
duplex
Packet Control Runt & CRC filtering, Broadcast storm control
Switching Fabric 8.8Gbps
Switch Management
Port Configuration
Port disable/enable. Auto-negotiation disable/enable.
10/100Mbps full and half duplex mode selection. Flow
control disable/enable
Port Status
Display each port’s disable/enable status, each port’s
link status, and speed duplex mode. Flow control
status
Trunk 7-trunk groups with up to 4-port per trunk
VLAN 26 Port-based VLAN groups

4
5
Port Mirroring 1 Mirroring port to monitor several mirrored ports.
The monitor modes are Disable, RX, TX, TX& RX
QoS Allow to assign low and high priority on each port
Bandwidth control Allow to assign rate control on each port
Standards Conformance
Network Standards
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE802.3x (Flow control)
IEEE 802.1p QoS
Operating Temperature 0~50ºC
Storage Temperature -40~70ºC
Humidity 5% to 95% (Non-condensing)
Regulation Compliance FCC Class A, VCCI Class A, CISPR 22 Class A

4
5
Chapter 2
Installation
This section describes the functionalities of the Switch components and guides how to
install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read
this chapter completely before continuing.
2.1 Product Description
The Switch provides 24 10/100Mbps Fast Ethernet ports with 2 open slots or 2 xed
10/100/1000Mbps ports and 2 SFP interfaces (port25, 26). The two open slots can be
installed by 10/100Base-TX TP port or 1000Base-T TP port and 100Base-FX or 1000Base-
SX / LX ber-optic interfaces. The distance range is 100 meters (TP) and 2 kilometers
(Multi-mode, ST or SC), up to 15 kilometers (Single-mode, SC). The 2 SFP interfaces can
install the optional Mini-GBIC module for 1000Base-SX / LX ber-optic interfaces. The
Switch with non-blocking backplane and simplies the task of upgrading your LAN to cater
for increased bandwidth demand.
Equipped with console and Web interface, the Web Smart Ethernet Switch can be
programmed for basic Switch management functions such as port speed conguration,
Port Trunking, VLAN, Port Mirroring, QoS, bandwidth control, Misc Conguration.
2.1.1 Product Overview
The Switch is a Web Smart Ethernet Switch with 24 RJ-45 10/100Mbps ports. The Switch
also provides up to two 100Mbps or 1000Mbps ber ports, and two 10/100Mbps TP or
1000Base-T ports for cost effective high-performance network connectivity. With its
8.8Gbps non-blocking switch fabric, the PLANET Switch can also provide a local, high
bandwidth, Fast Ethernet network for your departmental backbone plus the ability to trunk
four ports (800Mbps) to enable switch-to-switch backbone. The advanced functionality of
the Switch eliminates traditional problems associated with the use of Ethernet. Users can
be segregated using built-in VLAN functionality. These, coupled with the exible ber
module options, make the Switch one of the best and most cost-effective MTU switch
solutions for Multi-tenant service providers.
This product also supports store-and-forward forwarding scheme to ensure low latency
and high data integrity, eliminates unnecessary trafc and relieves congestion on critical
network paths. With an intelligent address recognition algorithm, Switch could recognize
up to 6K different MAC address and enables ltering and forwarding at full wire speed.

6
7
2.1.2 Switch Front Panel
Figure 2-1 shows front panel of FGSW-2402VS.
Figure 2-1 PLANET FGSW-2402VS Front Panel
Figure 2-2 shows front panel of FGSW-2620VS.
Figure 2-2 PLANET FGSW-2620VS Front Panel
Figure 2-3 shows front panel of FGSW-2620VSF.
Figure 2-3 PLANET FGSW-2620VSF Front Panel
2.1.3 LED Indicators
System
LED Color Function
PWR Green Lit: Power on
Per 10/100Mbps port
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully
established.
Blink: indicate that the switch is actively sending or re-
ceiving data over that port.
100 Orange Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps.

6
7
Per 10/100/1000Mbps port (FGSW-2620VS only)
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully
established.
Blink: indicate that the switch is actively sending or re-
ceiving data over that port.
100/1000 Green /
Orange
Orange: indicate that the port is operating at 1000Mbps.
Green: indicate that the port is operating at 100Mbps.
FDX Green
Lit: indicate that port is operating in full-duplex mode.
Off: indicate that port is operating in half-duplex mode.
Blink: if a collision is detected when the port is in half-
duplex mode.
Per 1000Base-T port (FGSW-2620VSF only)
LED Color Function
LNK/ACT/
1000 Green
Lit: indicate that the port is operating at 1000Mbps.
Off: indicate that the port is operating at 10Mbps or
100Mbps.
LNK/ACT/
100 Orange
Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps or
1000Mbps.
Per SFP interface (FGSW-2620VSF only)
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully
established.
Blink: indicate that the switch is actively sending or re-
ceiving data over that port.
FDX Orange Lit: indicate that the connection made through the cor-
responding port is running in Full Duplex mode.
 Note:
The 2 1000Base-T port and 2 STP interfaces are shared with
port 25/26 of FGSW-2620VSF. Either of them can operate at the
same time.

8
9
2.1.4 Extension Slots
The extension slots #25 and #26 of FGSW-2402VS can be a 10/100Base-TX, 1000Base-T
or 100Base-FX, 1000Base-SX/LX switching port as the extension module installed.
Please refer to the section 3.2.4 Port Conguration for the detailed installation and
settings.
2.1.5 Switch Rear Panel
The rear panel of the Switch indicates an AC inlet power socket, which ac-cepts input
power from 100 to 240VAC, 0.5A, 50-60Hz. Figure 2-4 shows Rear panel of the Switch.
Figure 2-4 Rear Panel of the Switch
Power Notice:
1. The device is a power-required device, it means, it will not work till it is pow-
ered. If your networks should active all the time, please consider using UPS
(Uninterrupted Power Supply) for your device. It will prevent you from network
data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect
your Switch from being damaged by unregulated surge or current to the Switch
or the power adapter.
2.2 Installing the Switch
This part describes how to install your Web Smart Ethernet Switch and make connections
to the Switch. Please read the following topics and perform the procedures in the order
being presented.
To install your Switch on a desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install a Switch on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch.
Step2: Place the Switch on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the Switch and the surrounding objects.
 Note:
When choosing a location, please keep in mind the environmental
restrictions discussed in Chapter 1, Section 4, Specication.
Step4: Connect your Switch to network devices.
A. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the