Planet FNSW-4800 User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
48-Port 10/100Mbps
Fast Ethernet Switch
FNSW-4800
User’s Manual
2. Product Features
Physical Port
● 4810/100MbpsFastEthernetports
● SupportsautoMDI/MDI-Xfunction
Layer 2 Features
● Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u
100BASE-TXEthernetstandard
● Features Store-and-Forward mode with wire-speed
lteringandforwardingrates
● Hardware Based 10/100Mbps, half / full duplex mode,
owcontrol,auto-negotiation
● Complies IEEE 802.3x ow control for full duplex opera-
tionandbackpressureforhalfduplexoperation
● Integrated address look-up engine, supporting 16K abso-
luteMACaddresses
● 9KJumbopacketsupport
● IEEE802.1QVLANpackettransparentsupport
● Automaticaddresslearningandaddressaging
● SupportsCSMA/CDprotocol
Hardware Features
● 100~240VAC,50~60Hz,0.3Auniversalpowerinput
● FCC,CEClassAcompliant
5. Switch Rear Panel
Figure2showstherearpaneloftheFastEthernetSwitch.
100-240V~ 50/60Hz 0.3A
Figure 2: FNSW-4800 Rear Panel
Power
Notice
1.The device is a power-required device,
meaningitwillnotworktillitispowered.If
yournetworksshouldbeactiveallthetime,
please consider using UPS (Uninterrupted
Power Supply) for your device. It will
prevent you from network data loss or
networkdowntime.
2. Insomeareas,installingasurgesuppression
device may also help to protect your Fast
Ethernet Switch from being damaged by
unregulated surge or current to the Switch
orthepoweradapter.
FlowControl
Backpressureforhalfduplex,
IEEE802.3xPauseFrameforfull
duplex
Temperature Operating:0~50degreesC
Storage:-10~70degreesC
Humidity
Operating:5%to90%
(non-condensing)
Storage:5%to90%
(non-condensing)
Standards Conformance
Regulation
Compliance FCCPart15ClassA,CE
Standards
Compliance
IEEE802.3(Ethernet)
IEEE802.3u(FastEthernet)
IEEE802.3x(Full-duplexFlow
Control)
Thank you for purchasing PLANET 48-Port 10/100Mbps
Unmanaged Fast Ethernet Switch, FNSW-4800. “Fast
Ethernet Switch” mentioned in this user’s manual means
theFNSW-4800.
● Theboxshouldcontainthefollowingitems:
● FastEthernetSwitchx1
● User’sManualx1
● PowerCordx1
● RubberFeetx4
● Rack-mountingBracketx2withAttachmentScrewx8
Ifanyofthesearemissingordamaged,pleasecontactyour
dealer immediately; if possible, retain the carton including
theoriginalpackingmaterial,and use themagaintorepack
the product in case there is a need to return it to us for
repair.
3. Product Specications
Product FNSW-4800
Hardware Specications
HardwareVersion V3
10/100BASE-TX
MDI/MDIXPorts 48
Throughput
(packetpersecond) 7.14Mpps
SwitchFabric 9.6Gbps
PowerRequirements 100~240VAC,50/60Hz,0.3A
PowerConsumption/
Dissipation 10watts/34BTU
Dimensions
(WxDxH) 440x180x44mm,1Uheight
Weight 2kg
SwitchProcessing
Scheme Store-and-Forward
AddressTable 16Kentries
PacketBuffer 1056Kbytes
JumboFrameSize 9216bytes
IEEE802.1QVLAN
Transparent Support
4. Switch Front Panel
Figure1showsthefrontpaneloftheFastEthernetSwitch.
FNSW-4800
48-Port 10/100Mbps Fast Ethernet Switch
PWR
159 13 17 21 25 29 33 37 41 45
26 10 14 18 22 26 30 34 38 42 46
3 7 11 15 19 23 27 31 35 39 43 47
4812 16 20 24 28 32 36 40 44 48
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
ACT
LNK
Figure 1:FNSW-4800 Front Panel
LED Indicators
System
LED Color Function
PWR Green Itlightstoindicatethatthe
Switchhaspower.
Per 10/100Mbps Port
LED Color Function
LNK/ACT Green
Itlightstoindicatethelink
throughthatportisestablished
successfully.
Itblinkstoindicatethatthe
Switchisactivelysendingor
receivingdataoverthatport.
6. Installing the Switch
This part describes how to install your Fast Ethernet Switch
andmakeconnections toit.Pleasereadthe followingtopics
andperformtheproceduresintheorderbeingpresented.
Note
This Fast Ethernet Switch does not need
softwareconfiguration.
Department Networking Installation
To install the Fast Ethernet Switch in a department
networkingenvironment,simplyfollowthestepsbelow:
Step 1: Attach the rubber feet to the recessed areas on
thebottomoftheFastEthernetSwitch.
Step 2: Place the Fast Ethernet Switch that is near an AC
powersource.
Step 3: Keep enough ventilation space between the Fast
EthernetSwitchandthesurroundingobjects.

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
Step 4: Connect your Fast Ethernet Switch to network
devices.
A. Connect one end of a standard network cable
to the 10/100 RJ45 ports on the front of the
FastEthernetSwitch.
B. Connect the other end of the cable to the
network devices such as printer servers,
workstationsorrouters.
Step 5: SupplypowertotheFastEthernetSwitch.
A. ConnectoneendofthepowercabletotheFast
EthernetSwitch.
B. Connect the power plug of the power cable to
astandardwalloutlet.
When the Fast Ethernet Switch receives power, the Power
LEDshouldremainsolidgreen.
Step 3: Securethebracketstightly.
Step 4: Follow the same steps to attach the second
brackettotheoppositeside.
Step 5: After the brackets are attached to the Fast
Ethernet Switch, use suitable screws to securely
attachthebracketstotherack,asshowninFigure
4.
FNSW-4800
48-Port 10/100Mbps Fast Ethernet Switch
PWR
159 13 17 21 25 29 33 37 41 45
26 10 14 18 22 26 30 34 38 42 46
3711 15 19 23 27 31 35 39 43 47
4812 16 20 24 28 32 36 40 44 48
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
ACT
LNK
Figure 4: Mounting the Fast Ethernet Switch on a Rack
Step 6: Proceed with Steps 4 and 5 of Department
Networking Installation to connect the network
cabling and supply power to your Fast Ethernet
Switch.
Rack Mounting
To install the Fast Ethernet Switch in a 19-inch standard
rack,followtheinstructionsdescribedbelow.
Step 1: Place your Fast Ethernet Switch on a hard at
surface, with the front panel positioned towards
yourfrontside.
Step 2: Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package.Figure3showshowtoattachbracketsto
onesideoftheFastEthernetSwitch.
FNSW-4800
48-Port 10/100Mbps Fast Ethernet Switch
PWR
159 13 17 21 25 29 33 37 41 45
26 10 14 18 22 26 30 34 38 42 46
3711 15 19 23 27 31 35 39 43 47
4812 16 20 24 28 32 36 40 44 48
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
ACT
LNK
Figure 3: Attaching the brackets to the Fast Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to
the parts by using incorrect screws would
invalidateyourwarranty.
Customer Support
ThankyouforpurchasingPLANETproducts. Youcanbrowse
our online FAQ resource at the PLANET Web site rst to
checkifitcouldsolveyourissue. If you need moresupport
information,pleasecontactPLANETswitchsupportteam.
PLANETonlineFAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product: 48-Port 10/100Base-TX Fast Ethernet Switch
*Model Number: FNSW-4800
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022 (2010 + AC:2011)
EN 61000-3-2 (2006+A1:2009+A2:2009)
EN 61000-3-3 (2013)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
EN60950-1 (2006 + A11:2009 + A1:2010 +
A12:2011)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 16th Jan., 2014
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]