Planet G.SHDSL.bis Bridge Router GRT-504 User manual

G.SHDSL.bis Bridge Router
GRT-501 / GRT-504
Quick Installation Guide

Table of Contents
Overview ................................................................................................ 3
1. Package Content......................................................................................... 4
2. Hardware Description.................................................................................. 5
3. Quick Installation........................................................................................ 8
3.1 Bridge Mode........................................................................................ 9
3.2 Routing Mode for PPPoA and PPPoE with IP Sharing ..............................11
3.3 Routing Mode for IPoA or EoA .............................................................13
3.4 LAN-to-LAN Connection with Bridge Mode.............................................16
4. Furtherconguration..................................................................................19

Overview
Thank you for purchases the Planet GRT-501 or GRT-504. The GRT-501 and GRT-
504 are the G.SHDSL.bis routers that comply with ITU-T G.991.2 standard and
provide affordable, exible, efcient Internet access solution for SOHO and Small
Medium Business environment. The GRT-501 and GRT-504 support business-class,
multi-range from 192 Kbps to 5.7 Mbps (2-wire) and 384 Kbps to 11.4 Mbps (4-
wire)symmetricdataratesbyusingexistingtelephonecopperwires.
This quick installation guide includes the following sections:
1. Package Content
2. Hardware Description: Hardware outlook and panel description
3. Quick Installation: Quick setup through Web browser
4.FurtherConguration

4
1. Package Content
GRT-501 / GRT-504
G.SHDSL.bisBridgeRouterx1
PowerAdapterx1
QuickInstallationGuidex1
User’smanualCDx1
ConsoleCablex1
RJ-45toRJ-11Cablex1
If any of the above items are missing or damaged, please contact your local dealer
for support.
ó
ó
ó
ó
ó
ó

5
2. Hardware Description
GRT-501
►Front Panel
►LED / Port Denition
LEDs Color Active Description
PWR Green ON The power adaptor is connected to GRT-501
WAN
LNK Green ON SHDSL.bis connection is established
Green Blink SHDSL.bis is handshaking
ACT Green Blink Transmit data or receive data over SHDSL.bis
link
LAN
10M/
ACT
Green ON LAN Port connect with 10M Ethernet link
Green Blink LAN Port Transmit or receive data in 10M mode
100M/
ACT
Green ON LAN Port connect with 100M Ethernet link
Green Blink LAN Port Transmit or receive data in 100M mode
ALM Red ON SHDSL.bis line connection is dropped
Red Blink SHDSL.bis self test
► Rear View

6
►Port Denition
Port Description
DC-IN Power connector with 9V DC 1.0A
LAN Ethernet 10/100BaseT for LAN port (RJ-45)
CONSOLE RS-232C(DB9)forsystemcongurationandmaintenance
LINE SHDSL.bis interface for WAN Port
RST The reset button, the router restore the default settings when press
this button until reboot.
GRT-504
►Front Panel
►LED / Port Denition
LEDs Color Active Description
PWR Green ON The power adaptor is connected to GRT-504
WAN
LNK Green ON G.SHDSL.bis connection is established
Green Blink G.SHDSL.bis is handshaking
ACT Green Blink Transmit data or receive data over G.SHDSL.
bis link
LAN 1/2/3/4 Green ON LAN Port connect with Ethernet link
1/2/3/4 Green Blink LAN Port Transmit or receive data
ALM Red ON G.SHDSL.bis line connection is dropped
Red Blink G.SHDSL.bis self test

7
►Rear View
►Port Denition
Port Description
DC-IN Power connector with 9V DC 1.0A
LAN (1/2/3/4) Ethernet 10/100Base-TX for LAN port (RJ-45)
CONSOLE RS-232C(DB9)forsystemcongurationandmaintenance
LINE G.SHDSL.bis interface for WAN Port
RST The reset button, the router restore the default settings when
press this button until reboot.

8
3. Quick Installation
Before proceeding any further, please make sure correct network cable is used for
connecting the LAN port from your computer to GRT-501 or GRT-504. The LAN LNK
indicator on the front panel shall light if a correct cable is used.
By default, the GRT-501 or GRT-504 is shipped with its DHCP Server function
enabled. This means the client computers on the LAN network including the
Administrator PC can set their TCP/IP settings to automatically obtain an IP address
from the GRT-501 or GRT-504. Starting your web browser and connecting to the
management IP of GRT-501 or GRT-504, wait for the login screen appears. When
you see the login screen, enter the correct user name and password to login the
GRT-501 or GRT-504.
Open web browser and type http://192.168.0.1inthebrowser’saddressbox.
This number is the default IP address for this device. Press Enter.
A user name and password prompt will appear. The default user name and pass-
word are “root”. Click OK button and you will login the GRT-501 or GRT-504 for
management.
Note
The factory default management IP and subnet mask of GRT-501
or GRT-504 is 192.168.0.1 and 255.255.255.0 respectively. And the
default user name and password is “root”.
ó
ó

9
This chapter provides quickly setup procedure for four major connection modes:
n Section 3.1: Bridge Mode
n Section 3.2: Routing Mode for PPPoA and PPPoE
n Section 3.3: Routing Mode for IPoA or EoA
n Section 3.4: LAN to LAN Bridge Mode
Please verify your connection mode and check the corresponding section to quickly
install your GRT-501 or GRT-504.
3.1 Bridge Mode
Web UI Conguration
Step 1.
Click Basic on the left menu, the BASIC setting screen will display. And then select
Bridge and CPE Side to setup Bridge mode of the Router and then click Next for
thenextsetting.
This product can be setup as two G.SHDSL.bis working mode: CO (Central Ofce)
and CPE (Customer Premises Equipment). For connection with DSLAM, the
G.SHDSL.bis working mode is CPE.

10
Step 2.
Enter Parameters in BASIC – STEP2:
LAN
IP: 192.168.0.1
Subnet Mask: 255.255.255.0
Gateway: 192.168.0.254 (The Gateway IP is provided by ISP)
Host Name: SOHO
Some of the ISP requires the Host Name as identication. You may check with
ISPtoseeifyourInternetservicehasbeenconguredwithahostname. Inmost
cases,thiseldcanbeignored.
WAN1
VPI: 0
VCI: 32
Click LLC, and then Click Nextfornextsetting.
Step 3.
The screen will prompt the new congured parameters. Check the parameters and
click Restart. The router will reboot with the new setting or Continuetocongure
another parameters.

11
3.2 Routing Mode for PPPoA and PPPoE with IP Sharing
Web UI Conguration
Step 1.
For Route Mode with Point-to-Point Protocol over ATM and Ethernet, follow the
following setting. First, select ROUTE and CPE Side, and then click Next for
setting others parameters.
Step 2.
TheembeddedDHCPserverassignsnetworkcongurationinformationatmost253
users accessing the Internet in the same time.
Click Nextfornextsetting.

12
Step 3.
Assign the IP pool for your DHCP server. Click Next.
Step 4.
Enter the Parameters in BASIC – STEP4
VPI: 0
VCI: 32
AAL5 Encapsulation: LLC
Protocol: PPPoA + NAT or PPPoE + NAT
Click Next to setup the ISP setting.
Step 5.
1. Enter user name provided by ISP: test
2. Enter Password provided by ISP: test
3.Re-enterPasswordforconrmation:test
The user name and password provided by your ISP.
4. Idle Time: 10
If you want your Internet connection to remain on at all time, enter 0 in the Idle
Timeeld.
5. IP Type: Dynamic
6. Click Next.

13
Step 6.
The screen will prompt the new congured parameters. Check the parameters and
click Restart. The router will reboot with the new setting or Continuetocongure
another parameters.
3.3 Routing Mode for IPoA or EoA
Web UI Conguration
Step 1.
For Route Mode with IPoA and EoA, follow the following setting. First, select
ROUTE and CPE Side, and then click Next for setting others parameters.

14
Step 2.
TheembeddedDHCPserverassignsnetworkcongurationinformationatmost253
users accessing the Internet in the same time.
Click Nextfornextsetting.
Step 3.
Assign the IP pool for your DHCP server. Click Next.
Step 4.
Enter Parameters in BASIC – STEP4
Wan Parameters;
VPI: 0
VCI: 32
AAL5 Encapsulation: LLC
Protocol: IPoA , EoA , IPoA + NAT or EoA + NAT
Click Next to setup the IP parameters.

15
Step 5.
Enter Parameters in WAN setting.
1. IP Address: 10.1.2.1
2. Subnet mask: 255.255.255.0
3. Gateway: 10.1.2.2
 YourISPwillprovideaboveinformationtoyou.
4. DNS Server 1: 168.95.1.1
 YourISPwillprovideatleastoneDNSServerIPaddress.
5. Click Next.
Step 6.
The screen will prompt the new congured parameters. Check the parameters and
click Restart.The routerwillreboot withthenew settingorContinuetocongure
another parameters.

16
3.4 LAN-to-LAN Connection with Bridge Mode
Web UI Conguration
CO side
Step 1.
Click Bridge and CO Side to setup Bridge mode of the Router and then
click Next.

17
Step 2.
Enter LAN Parameters
1. IP: 192.168.0.1
2. Subnet Mask: 255.255.255.0
3. Gateway: 192.168.0.2
Host Name: SOHO
Enter WAN Parameters
1. VPI: 0
2. VCI: 32
3. Encapsulation: LLC
4. Click Next
Thescreenwill promptthenewconguredparameters.Checkthepa-
rameters and Click Restart The router will reboot with the new setting.
CPE side
Step 1.
Click Bridge and CPE Side to setup Bridge mode of the Router and then
click Next.

18
Step 2.
Enter LAN Parameters
1. IP: 192.168.0.2
2. Subnet Mask: 255.255.255.0
3. Gateway: 192.168.0.1
Host Name: SOHO
Enter WAN Parameters
1. VPI: 0
2. VCI: 32
3. Encapsulation: LLC
4. Click Next
The screen will prompt the new congured parameters. Check the parameters and
Click Restart The router will reboot with the new setting.
After rebooting, the GRT-501 or GRT-504 will establish a connection and the PC1
and PC2 can access to each other.

19
4. Further conguration
The above steps introduce simple congurations for GRT-501 or GRT-504. For
further congurations such as DMZ, Virtual Server, or VLAN functions, please refer
to the user’s manual in the CD. If you have other questions, please contact the
local dealer or distributor where you purchased this product.

This page is intentionally left blank