Planet IVR-100 Series User manual

Industrial VPN Security Router
IVR-100 & IVR-300 Series
Quick Installation Guide

Table of Contents
1. Package Contents....................................................................................3
2. Connecting The Power Input ....................................................................4
2.1 Upper Panel ......................................................................................4
2.2 Wiring the Power Inputs.....................................................................5
2.3 Grounding the Device ........................................................................7
2.4 Wiring the Fault Alarm Contact...........................................................7
2.5 Wi-Fi Antenna Installation (IVR-300W) ................................................8
3. Hardware Installation...............................................................................9
3.1 DIN-rail Mounting Installation .............................................................9
3.2 Wall-mount Plate Mounting.................................................................9
3.3 Side Wall-mount Plate Mounting ....................................................... 10
4. Setup of the VPN Gateway..................................................................... 11
4.1 Requirements.................................................................................. 11
4.2 Logging in to the VPN Gateway ........................................................ 11
5. RecoveringBacktoDefaultConguration ................................................ 14
5.1 IP Address has been changed or admin password has been forgotten –14
6. Appendix .............................................................................................. 15
7. Customer Support ................................................................................. 16

3
1. Package Contents
Thank you for purchasing PLANET Industrial Security Gateway, IVR-100 and
IVR-300 series. The descriptions of these models are as follows
IVR-100 Industrial 5-Port 10/100/1000T VPN Security Gateway
IVR-300 Industrial 5-Port 10/100/1000T VPN Security Gateway with
Redundant Power
IVR-300W Industrial 5-Port 10/100/1000T + 802.11ax Wi-Fi VPN Security
Gateway
IVR-300FP Industrial 4-Port 10/100/1000T 802.3at PoE + 1-Port
10/100/1000T + 1-Port 1000X SFP VPN Security Gateway
Open the box of the Security Gateway and carefully unpack it. The box should
contain the following items:
Model
Item IVR-100 IVR-300 IVR-300W IVR-300FP
VPN Gateway x 1 x 1 x 1 x 1
QR Code Sheet x 1 x 1 x 1 x 1
CloudViewer QIG x 1 x 1 x 1 x 1
Wall-mount Kit x 1 x 1 x 1 x 1
Dust Cap x 5 x 5 x 5 x 5
SFP Cap x 1
RS485 3-pin Terminal Block x 1 x 1 x 1
Dual band Wi-Fi Antenna x 2
Antenna Dust Cap x 2
If any of the above items are damaged or missing, please contact your dealer
immediately.

4
2.Connecting The Power Input
This section describes the functionalities of the VPN Gateway’s components.
2.1 Upper Panel
The upper panel of the IVR-100 consists of one terminal block connector within
two DC power inputs.
Figure 2-1 shows the upper panel of the IVR-100 VPN Gateway.
DC Input:
9~48V , 1A max.
Fault
V1+ V2+
PWR2PWR1
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 2-1: IVR-100 Upper Panel
The Upper Panel of the IVR-300 series consists of two terminal block
connectors.
- Green terminal block connector: Power 1, Power 2 input and relay alarm
output
- Yellow terminal block connector: 2 digital input and 2 digital output
Figure 2-2 shows the upper panel of the IVR-300 / IVR-300W VPN Gateway.
Max. Fault Alarm Loading: 24V, 1A
DI1 DO0 DO1DI0 GNDGND
V1+ V2+
PWR1 PWR2Alarm
DC Input:
9-54V
, 1.8A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 2-2: IVR-300/IVR-300W Upper Panel

5
The Upper Panel of the IVR-300FP series consists of two terminal block
connectors.
- Green terminal block connector: Power 1, Power 2 input and relay alarm
output
- Yellow terminal block connector: 2 digital input and 2 digital output
Figure 2-3 shows the upper panel of the IVR-300FP VPN Gateway.
Max. Fault Alarm Loading: 24V, 1A
DI1 DO0 DO1DI0 GNDGND
V1+ V2+
PWR1 PWR2Alarm
DC Input:
48-54V
, 3A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 2-3: IVR-300FP Upper Panel
2.2 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of VPN Gateway is
used for two redundant power inputs. Please follow the steps below to insert
the power wire.
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
DC Input:
9~48V , 1A max.
Fault
V1+ V2+
PWR2PWR1
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 2-4: Power 1 and Power 2

6
Please make sure the input voltage is under the specification of
the Security Gateway.
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
Power 1 Fault/
Alarm
Power 2
+ - + -
The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
PWR1 and PWR2 must provide the same DC voltage while
operating with dual power input.

7
2.3 Grounding the Device
User MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
Max. Fault Alarm Loading: 24V, 1A
DI1 DO0 DO1DI0 GNDGND
V1+ V2+
PWR1 PWR2Alarm
DC Input:
48-54V
, 3A max.
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
2.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the Security Gateway will detect
the fault status of the power failure or port failure, and then will form an open
circuit. The following illustration shows an application example for wiring the
fault alarm contacts.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Alarm
Insert the wires into the fault alarm contacts

8
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A currents.
2.5 Wi-Fi Antenna Installation (IVR-300W)
Step 1: Fasten the two dual-band antennas to the antenna connectors on the
front panel of the IVR-300W.
Step 2: Youcanbendtheantennastotyouractualneeds.
Reset
RS485
P2
5G
P1
2.4G
Alarm
I/O
IVR-300W
WAN
WAN/LAN
LAN
5
3
1
4
2
1000
10/100
2.4G/5GHz
2.4G/5GHz
USB
GND
TxD+
RxD
Two Wi-Fi RP-SMA Connectors
Figure 2-5: IVR-300W Front Panel

9
3. Hardware Installation
This section guides you to installing the VPN Gateway on the DIN-rail and
wall. Basic knowledge of networking is assumed. Please read this chapter
completely before continuing.
The installation procedures of the IVR-100 & IVR-300 series are
the same as the ones shown below.
3.1 DIN-rail Mounting Installation
1
2
3.2 Wall-mount Plate Mounting

10
3.3 Side Wall-mount Plate Mounting
You must use the screws supplied with the wall-mounting
brackets. Damage caused to the parts by using incorrect screws
would invalidate your warranty.