Planet WAP-500N User manual

I

I
Copyright
Copyright 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. To assure continued compliance, for example, use
only shielded interface cables when connecting to computer or peripheral devices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.

This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-
5.25GHz band are restricted to indoor usage only.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with
radiator and your body.
CE Compliance Statement
This device meets the RED 2014/53/EU
public to electromagnetic fields by way of health protection.
when it is used
at a safe distance of
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the da
electrical equipment. All the
guidelines must
equipment.
WEEE regulation
To avoid the potential effects on the environment and human
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed
symbol. Do not dispose of WEEE as unsorted muni
separately.
Revision
User Manual of PLANET 5GHz 300
Mbps 802.11
Model: WAP-500N/WBS-500N
Rev: 1.0 (August, 2017)
Part No. EM-WAP-500N_WBS-
500N
II
located or operating in conjunction with any other antenna or transmitter.
5.25GHz band are restricted to indoor usage only.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with
the minimum distance
of
CE Compliance Statement
This device meets the RED 2014/53/EU
requirements on the limitation of exposure of the general
public to electromagnetic fields by way of health protection.
The device complies with RF specifications
at a safe distance of
20 cm from your body.
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the da
ngers of electric shock and static electricity when working with
guidelines must
be followed
at all times to ensure the safe use of the
To avoid the potential effects on the environment and human
health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed
symbol. Do not dispose of WEEE as unsorted muni
cipal waste;
WEEE
Mbps 802.11
n Wireless AP/CPE
500N
_v1.0
located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
of
20cm between the
requirements on the limitation of exposure of the general
The device complies with RF specifications
This equipment is designed with the utmost care for the safety of those who install and use it. However,
ngers of electric shock and static electricity when working with
at all times to ensure the safe use of the
health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed
-out wheeled bin
WEEE
should be collected

III
CONTENTS
Chapter 1.Product Introduction...........................................................................................................7
1.1 Package Contents...............................................................................................................7
1.2 Product Description............................................................................................................8
1.3 Product Features.................................................................................................................9
1.4 Hardware Description.......................................................................................................11
1.4.1 The Bottom Panel – Port ........................................................................................13
Chapter 2.Connecting to the AP........................................................................................................15
2.1 Preparation before Installation........................................................................................15
2.1.1 Safety Precautions..................................................................................................15
2.2 Installation Precautions....................................................................................................15
2.3 Installing the AP ................................................................................................................17
Chapter 3.Quick Installation Guide ...................................................................................................19
3.1 Manual Network Setup -- TCP/IP Configuration.............................................................19
3.1.1 Configuring the IP Address Manually .....................................................................19
3.2 Starting Setup in the Web UI............................................................................................22
Chapter 4.Configuring the AP............................................................................................................24
4.1 Operation Mode.................................................................................................................24
4.2 Status .................................................................................................................................25
4.2.1 Main........................................................................................................................25
4.2.2 Save/Reload ...........................................................................................................27
4.2.3 Wireless Client List.................................................................................................28
4.2.4 WDS Link List.........................................................................................................29
4.2.5 DHCP Client Table..................................................................................................29
4.2.6 Connection Status ..................................................................................................30
4.2.7 System Log.............................................................................................................31
4.3 System................................................................................................................................32
4.3.1 IP Settings...............................................................................................................32
4.3.2 Spanning Tree Settings ..........................................................................................33
4.4 Router (WISP Mode Only).................................................................................................34
4.4.1 DHCP Server Settings............................................................................................34
4.4.2 WAN Settings..........................................................................................................35
4.4.2.1. DHCP.............................................................................................................................36
4.4.2.2. Static IP..........................................................................................................................37
4.4.2.3. PPPoE...........................................................................................................................39
4.4.2.4. PPTP .............................................................................................................................41
4.4.3 VPN Passthrough ...................................................................................................42
4.4.4 Port Forwarding......................................................................................................43

IV
4.4.5 DMZ Settings..........................................................................................................44
4.5 Wireless..............................................................................................................................46
4.5.1 Wireless Network....................................................................................................46
4.5.2 WDS Link Settings..................................................................................................49
4.5.3 Security Settings.....................................................................................................50
4.5.4 Wireless MAC Filter................................................................................................60
4.5.5 Wireless Advanced Settings...................................................................................61
4.6 Management ......................................................................................................................63
4.6.1 Administration (Password Settings)........................................................................63
4.6.2 Management VLAN ................................................................................................63
4.6.3 SNMP Settings .......................................................................................................64
4.6.4 Backup/Restore Settings........................................................................................65
4.6.5 Auto Reboot Settings..............................................................................................66
4.6.6 Firmware Upgrade..................................................................................................66
4.6.7 Time Settings..........................................................................................................68
4.6.8 Wi-Fi Schedule .......................................................................................................69
4.6.9 CLI Settings ............................................................................................................70
4.6.10 Log..........................................................................................................................71
4.6.11 Diagnostics .............................................................................................................71
4.6.12 Logout.....................................................................................................................73
Appendix A: Troubleshooting............................................................................................................74
Appendix B: Use Planet Smart Discovery to find AP......................................................................76

V
FIGURES
F IGURE 1-1 T HREE - WAY V IEW (WAP-500N)........................................................................................................11
F IGURE 1-2 R EAR P ANEL (WAP-500N) ................................................................................................................12
F IGURE 1-3 B OTTOM P ANEL (WAP-500N/WBS-500N)........................................................................................13
F IGURE 1-4 P O E W ARNING L ABEL .......................................................................................................................13
F IGURE 2-1 P O E AND LAN PORT CONNECTION .....................................................................................................17
F IGURE 2-2 F INISH INSTALLATION AND CONNECT TO ANTENNAS (WAP-500N ONLY )...........................................17
F IGURE 2-3 P OLE M OUNTING ...............................................................................................................................18
F IGURE 2-4 W ALL M OUNTING ..............................................................................................................................18
F IGURE 3-1 TCP/IP S ETTING ................................................................................................................................20
F IGURE 3-2 W INDOWS S TART M ENU ....................................................................................................................21
F IGURE 3-3 S UCCESSFUL RESULT OF P ING COMMAND ..........................................................................................21
F IGURE 3-4 F AILED RESULT OF P ING COMMAND ...................................................................................................22
F IGURE 3-5 L OGIN BY DEFAULT IP ADDRESS .........................................................................................................22
F IGURE 3-6 L OGIN W INDOW ................................................................................................................................22
F IGURE 3-7 W EB UI S CREENSHOT ........................................................................................................................23
F IGURE 4-1 S YSTEM M ENU - R ESET .....................................................................................................................25
F IGURE 4-2 S YSTEM M ENU – L ANGUAGE OPTION ................................................................................................25
F IGURE 4-3 M AIN S TATUS ....................................................................................................................................26
F IGURE 4-4 S AVE /R ELOAD ...................................................................................................................................27
F IGURE 4-5 S AVE /R ELOAD - D EFAULT ..................................................................................................................28
F IGURE 4-6 W IRELESS C LIENT L IST .....................................................................................................................28
F IGURE 4-7 K ICK THE CLIENT ...............................................................................................................................28
F IGURE 4-8 WDS L INK S TATUS ............................................................................................................................29
F IGURE 4-9 DHCP C LIENT L IST ...........................................................................................................................29
F IGURE 4-10 C ONNECTION S TATUS ......................................................................................................................30
F IGURE 4-11 S YSTEM L OG ....................................................................................................................................31
F IGURE 4-12 LAN IP S ETTINGS ............................................................................................................................32
F IGURE 4-13 S PANNING T REE S ETTINGS ...............................................................................................................33
F IGURE 4-14 DHCP S ERVER S ETTINGS ................................................................................................................34
F IGURE 4-15 WAN S ETTINGS – A LL .....................................................................................................................35
F IGURE 4-16 WAN S ETTINGS – DHCP.................................................................................................................37
F IGURE 4-17 WAN S ETTINGS – S TATIC IP............................................................................................................38
F IGURE 4-18 WAN S ETTINGS – PPPOE................................................................................................................39
F IGURE 4-19 WAN S ETTINGS – PPTP ..................................................................................................................41
F IGURE 4-20 VPN P ASSTHROUGH ........................................................................................................................42
F IGURE 4-21 P ORT F ORWARDING ..........................................................................................................................43
F IGURE 4-22 P ORT F ORWARDING ..........................................................................................................................44
F IGURE 4-23 DMZ ...............................................................................................................................................45
F IGURE 4-24 W IRELESS N ETWORK – AP/WDS AP M ODE ....................................................................................46
F IGURE 4-25 W IRELESS N ETWORK – SSID P ROFILE .............................................................................................47
F IGURE 4-26 W IRELESS N ETWORK – CB/WDS STA/CR/R EPEATER M ODE .........................................................48
F IGURE 4-27 WDS L INK S ETTINGS – WDS B RIDGE M ODE ..................................................................................49

VI
F IGURE 4-28 S ECURITY S ETTINGS – AP/WDS AP M ODE .....................................................................................50
F IGURE 4-29 S ECURITY S ETTINGS – CB/WDS STA/CR/R EPEATER M ODE ...........................................................51
F IGURE 4-30 S ECURITY S ETTINGS – WDS B RIDGE M ODE ....................................................................................51
F IGURE 4-31 S ECURITY S ETTINGS – WEP ............................................................................................................52
F IGURE 4-32 S ECURITY S ETTINGS – WPA-PSK....................................................................................................53
F IGURE 4-33 S ECURITY S ETTINGS – WPA2-PSK..................................................................................................54
F IGURE 4-34 S ECURITY S ETTINGS – WPA-PSK M IXED ........................................................................................54
F IGURE 4-35 S ECURITY S ETTINGS – WPA (WPA E NTERPRISE ).............................................................................55
F IGURE 4-36 S ECURITY S ETTINGS – WPA2 (WPA2 E NTERPRISE ) ........................................................................56
F IGURE 4-37 S ECURITY S ETTINGS – WPA M IXED (WPA M IXED E NTERPRISE ).....................................................58
F IGURE 4-38 W IRELESS MAC F ILTER ...................................................................................................................60
F IGURE 4-39 W IRELESS A DVANCED S ETTINGS .....................................................................................................61
F IGURE 4-40 A DMINISTRATION (P ASSWORD S ETTINGS )........................................................................................63
F IGURE 4-41 M ANAGEMENT VLAN.....................................................................................................................63
F IGURE 4-42 SNMP S ETTINGS .............................................................................................................................64
F IGURE 4-43 B ACKUP /R ESTORE S ETTINGS ...........................................................................................................65
F IGURE 4-44 A UTO R EBOOT S ETTINGS .................................................................................................................66
F IGURE 4-45 F IRMWARE U PGRADE .......................................................................................................................67
F IGURE 4-46 T IME S ETTINGS ................................................................................................................................68
F IGURE 4-47 W I -F I S CHEDULE .............................................................................................................................69
F IGURE 4-48 CLI S ETTINGS ..................................................................................................................................70
F IGURE 4-49 L OG .................................................................................................................................................71
F IGURE 4-50 D IAGNOSTICS ...................................................................................................................................72
F IGURE 4-51 L OGOUT ...........................................................................................................................................73

1.1 Package Contents
Thank you for choosing PLANET
WAP
contents inside the package box.
WBS-500N/WAP-500N
Screw Set x 1
If there is any item miss
immediately.
User Manual of
WAP
-7-
Chapter 1.
Product I
WAP
-500N/WBS-500N series. Before installing the
AP
Quick Installation Guide
Mounting Strap
PoE Injector & Power Cord
If there is any item miss
ing
or damaged, please contact the seller
WAP
-500N/WBS-500N
Product I
ntroduction
AP
/CPE, please verify the
Mounting Strap
x 2
Antenna x 2
or damaged, please contact the seller

User Manual of WAP-500N/WBS-500N
-8-
1.2 Product Description
Cost-effective Wireless Solution with Superior Performance
PLANET WAP-500N/WBS-500N 300Mbps 802.11n Wireless AP/CPE offers a better range and excellent throughput. Via
the WAP-500N/WBS-500N's RP-SMA antenna connectors, it is easy to build different point to multi-point applications with
good diversity coverage and better noise immunity effect, thus heightening the performance and stability of a long-distance
connectivity.
Designed for Various Requirements
The WAP-500N/WBS-500N is dedicatedly designed for WISP solution that provides CPE users with Internet access via
the WISP provider in rural areas. Besides, it caters to various wireless communication connectivity , thus meeting users’
application requirements.
Multiple SSIDs with VLAN Tagging
Multiple SSIDs can broadcast up to four wireless networks with different names. For management purposes, the
IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the
wireless access. This makes it possible for the WAP-500N/WBS-500N to work with managed Ethernet switches
to have VLANs assigned for a different access level and authority.
Flexible and Reliable Characteristics
The WAP-500N/WBS-500N is definitely suitable for wireless IP surveillance, and bridge link of building to
building and backbone of public service. Additionally, the self-healing capability keeps connection alive all the
time. With the IP55-rated UV-resistant enclosure, the WAP-500N/WBS-500N can perform normally under
rigorous weather conditions, meaning it can be installed in any harsh, environments. With the proprietary
Power over Ethernet (PoE) design, the WAP-500N/WBS-500N can be easily installed in the areas where
power outlets are not available.
Advanced Security and Rigorous Authentication
The WAP-500N/WBS-500N supports 152-bit WEP, WPA/WPA2, WPA-PSK and WPA2-PSK wireless
encryptions, the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively
prevent eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access.
Furthermore, any users are granted or denied access to the wireless LAN network based on the ACL (Access
Control List) that the administrator pre-established.

User Manual of WAP-500N/WBS-500N
-9-
Easy Deployment and Management
With user-friendly Web UI and comprehensive management features including client limit control and wireless
traffic shaping, the WAP-500N/WBS-500N is easy to limit the client access and inbound/outbound bandwidth
control, even for users who have no experience in setting up a wireless network. Furthermore, with the Planet
Smart Discovery Utility, SNMP and diagnostics tools, the WAP-500N/WBS-500N is convenient to be managed
remotely.
1.3 Product Features
Industrial Compliant Wireless LAN and LAN
Compliant with the IEEE 802.11a/n wireless technology
2T2R architecture with data rate of up to 300Mbps
Equipped with two 10/100Mbps RJ45 ports, with auto MDI/MDI-X supported
Fixed Network Broadband Router
Supported WAN connection types in WISP mode: DHCP, Static IP, PPPoE, PPTP
Supports Port Forwarding and DMZ for various networking applications
Supports DHCP server in WISP mode
RF Interface Characteristics
Built-in RP-SMA connectors
High output power
Environmental Characteristics
IP55 rating
Passive Power over Ethernet design
Operating temperature: -20~70°C
Multiple Operation Modes and Wireless Features
Multiple operation modes: AP, WDS, WISP
WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
Wireless Traffic Shaping to control the upload/download bandwidth
Wi-Fi scheduler allows to enable or disable based on predefined schedule
Secure Network Connection
Full encryption supported: 64-/128-/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X
RADIUS authentication
Supports 802.1Q VLAN pass-through over WDS and SSID-to-VLAN mapping
Supports up to 50 entries of MAC address filtering

User Manual of WAP-500N/WBS-500N
-10-
Easy Installation and Management
IPv4/IPv6 dual-stack management networks
Multilingual Web User Interface: English, Spanish, French, German, Portuguese, Russian,
Simplified Chinese
CLI command and SNMP-based management interface
Self-healing mechanism through system auto reboot setting
System status monitoring through remote Syslog Server and Device Discovery
Diagnostic tools include Ping, Traceroute and Speed
Planet Smart Discovery Utility allows administrator to discover and locate each AP

1.4
Hardware Description
Dimensions (W x D x H):
100 x 29 x 186mm
User Manual of
WAP
-11-
Hardware Description
100 x 29 x 186mm
(without antennas)/
100 x 29 x 380mm
Figure 1-1 Three-way View
WAP
-500N/WBS-500N
100 x 29 x 380mm
(with antennas)

Rear Panel – LED
LED Definition
LED
State
Power On
Off
LAN Ports
On
Blinking
Off
WLAN
On
Blinking
Off
Signal Strength
(CB/WDS
STA/CR only)
Green
Orange
Red
User Manual of
WAP
-12-
Figure 1-2 Rear Panel
State
Meaning
The device is powered on
The device is powered off
Port linked
Blinking
Data is transmitting or receiving
No link
The wireless radio is on
Blinking
Data is transmitting or receiving
The wireless radio is off
Green
LED on Signal is good
Orange
LED on Signal is normal
Red
LED on Signal is poor
Table 2-1 The LED indication
WAP
-500N/WBS-500N
Data is transmitting or receiving
data
Data is transmitting or receiving
over wireless

1.4.1 The Bottom Panel –
Port
The Bottom panel provides
the physical connectors connected to the power adapter and any other network
device. Figure 1-5 shows the bottom
Bottom Panel
Figure
PoE Warning Label
Hardware Interface Definition
Object
Description
Antenna Connectors
2
RP
Passive PoE LAN Port
10/100Mbps RJ45 port,
Passive
Pin
Pin 4, 5
Pin 7, 8
NOTE: Please use the 24VDC Passive PoE only (included)
User Manual of
WAP
-13-
Port
the physical connectors connected to the power adapter and any other network
panel of the WAP-500N/WBS-500N.
Figure
1-3 Bottom Panel (WAP-500N/WBS-500N)
Figure 1-4 PoE Warning Label
Description
RP
-SMA (Female) antenna connectors
10/100Mbps RJ45 port,
auto MDI/MDI-X
Passive
PoE/PD supported, 24VDC In
assignment:
Pin 4, 5
(+)
Pin 7, 8
(-)
NOTE: Please use the 24VDC Passive PoE only (included)
WAP
-500N/WBS-500N
the physical connectors connected to the power adapter and any other network
NOTE: Please use the 24VDC Passive PoE only (included)
.

User Manual of WAP-500N/WBS-500N
-14-
LAN Port 10/100Mbps RJ45 port, auto MDI/MDI-X
Reset Button Press and hold the Reset button on the device for over 10 seconds
to return to the factory default setting.
Table 2-2 Hardware Interface Definition

User Manual of WAP-500N/WBS-500N
-15-
Chapter 2.Connecting to the AP
2.1 Preparation before Installation
2.1.1 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WBS-500N or WAP-500N for the first time, for your safety as well as others’,
please seek assistance from a installer who has received safety training on the hazards involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4. When installing the WBS-500N or WAP-500N, please note the following things:
♦ Do not use a metal ladder;
♦ Do not work on a wet or windy day;
♦ Wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
2.2 Installation Precautions
 Users MUST use a proper and well-installed surge arrestor and grounding kit with the WBS-500N or
WAP-500N; otherwise, a random lightning could easily cause fatal damage to the WBS-500N or
WAP-500N. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
 Users MUST use the “Power cord and PoE Injector” shipped in the box with the WBS-500N or
WAP-500N. Use of other options will cause damage to the WBS-500N or WAP-500N.

User Manual of WAP-500N/WBS-500N
-16-
INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines
are anywhere where possible contact can be made. Antennas, masts, towers,
guy wires or cables may lean or fall and contact these lines. People may be
injured or killed if they are touching or holding any part of equipment when it
contacts electric lines. Make sure that equipment or personnel do not come in
contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest power
line should be at least twice the total length of the mast/antenna combination.
This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
 Select equipment locations that will allow safe, simple equipment installation.
 Don’t work alone. A friend or co-worker can save your life if an accident happens.
 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
 Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
 Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
 DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
 Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.
!

2.3 Installing the AP
Please install the AP
according to the following
hands dry.
Step 1. PoE and LAN port
connection:
(1) Remove the bottom
cover
(2)
Connect one end of the Ethernet cable into the LAN (Passive PoE) port of the device and the other
end to the PoE port on the PoE Injector.
(3)
Connect the power cord with the PoE Injector and plug the other end into an elec
(4)
Connect the second Ethernet cable into the LAN port of the PoE Injector and the other end to the
Ethernet port on the computer.
Figure
Step 2. Attach the antennas
onto the antenna connectors of the device and place the bottom cover back into
the device to finish the i
nstallation
Figure
2
User Manual of
WAP
-17-
according to the following
Step
s. Don't forget to pull out the power plug and keep your
connection:
cover
.
Connect one end of the Ethernet cable into the LAN (Passive PoE) port of the device and the other
end to the PoE port on the PoE Injector.
Connect the power cord with the PoE Injector and plug the other end into an elec
Connect the second Ethernet cable into the LAN port of the PoE Injector and the other end to the
Ethernet port on the computer.
Figure
2-1 PoE and LAN port connection
onto the antenna connectors of the device and place the bottom cover back into
nstallation
.
2
-2 Finish installation and connect to antennas
WAP
-500N/WBS-500N
s. Don't forget to pull out the power plug and keep your
Connect one end of the Ethernet cable into the LAN (Passive PoE) port of the device and the other
Connect the power cord with the PoE Injector and plug the other end into an elec
trical outlet.
Connect the second Ethernet cable into the LAN port of the PoE Injector and the other end to the
onto the antenna connectors of the device and place the bottom cover back into

Step 3. Pole Mounting:
(1) Thread two
mounting straps through the mounting bracket on the back of the device
(2)
Position the device on a pole and secure both mounting straps to finish the installation.
Step 4. Wall Mounting:
(1)
Secure the adhesive label to a position on the wall where you would like to install the device
(2)
Follow the plotting sticker to drill two holes and secure the plastic anchors
(3)
Align the screw holes on the mounting bracket with the screws and then
wall
to finish the installation
User Manual of
WAP
-18-
mounting straps through the mounting bracket on the back of the device
Position the device on a pole and secure both mounting straps to finish the installation.
Figure 2-3 Pole Mounting
Secure the adhesive label to a position on the wall where you would like to install the device
Follow the plotting sticker to drill two holes and secure the plastic anchors
Align the screw holes on the mounting bracket with the screws and then
to finish the installation
.
Figure 2-4 Wall Mounting
WAP
-500N/WBS-500N
mounting straps through the mounting bracket on the back of the device
.
Position the device on a pole and secure both mounting straps to finish the installation.
Secure the adhesive label to a position on the wall where you would like to install the device
.
Follow the plotting sticker to drill two holes and secure the plastic anchors
.
Align the screw holes on the mounting bracket with the screws and then
install the device on the

User Manual of WAP-500N/WBS-500N
-19-
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-
time
configuration.
3.1 Manual Network Setup -- TCP/IP Configuration
The default IP address of the WBS-500N and WAP-500N is 192.168.1.253. And the default Subnet Mask is
255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for
description.
Connect the WBS-500N or WAP-500N with your PC via an Ethernet cable which is then plugged into a LAN port
of the PoE injector with one end and into a LAN port of the PC with the other end. Then power on the WBS-500N
and WAP-500N via PoE injector or PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. And the
procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and refer
to the Ethernet adapter’s manual if needed.
3.1.1 Configuring the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to
252); subnet mask is 255.255.255.0.
1 Select Use the following IP address radio button.
2 If the AP's LAN IP address is 192.168.1.253, enter IP address 192.168.1.x (x is from 2 to 254 except
192.168.1.253), and subnet mask 255.255.255.0.
3 Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can
enter the DNS server IP address which has been provided by your ISP