Planet FSD-805 User manual

10/100Mbps
Fast Ethernet Switch
FSD-805/FSD-805SC/FSD-805ST/FSD-805S15
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2009.
Contents subjects to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will
work properly in all environments and applications, and makes
no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual
is accurate; PLANET disclaims liability for any inaccuracies or
omissions that may have occurred.
Information in this User’s Manual is subject to change without
notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies
that may be contained in this User’s Manual. PLANET makes no
commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements
to this User’s Manual and/or to the products described in this
User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect,
misleading, or incomplete, we would appreciate your comments
and suggestions.

FCC Warning
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and
human health as a result of the presence of
hazardous substances in electrical and electronic
equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
PLANET 8-Port 10/100Mbps Fast Ethernet Switch User's Manual
For Models: FSD-805 / FSD-805SC / FSD-805ST / FSD-805S15
Revision: 1.1 (February, 2009)
Part No: EM_FSD805v1.1 (2350-A31150-001)

Table of Contents
1. INTRODUCTION................................................................ 5
1.1 Package Contents .......................................................5
1.2 How to Use This Manual ............................................ 5
1.3 Product Features ........................................................ 6
1.4 Product Specications ................................................. 7
2. INSTALLATION.................................................................. 8
2.1 Product Description..................................................... 8
2.1.1 Product Overview.............................................. 9
2.1.2 Switch Front Panel ............................................9
2.1.3 LED Indicators ................................................ 10
2.1.4 Switch Rear Panel ........................................... 10
2.2 Installing the Switch ................................................. 11
2.2.1 Desktop Installation ........................................ 11
3. SWITCH OPERATION ....................................................... 13
3.1 Address Table........................................................... 13
3.2 Learning .................................................................. 13
3.3 Forwarding & Filtering............................................... 13
3.4 Store-and-Forward.................................................... 14
3.5 Auto-Negotiation ...................................................... 15
4. TROUBLESHOOTING........................................................ 16
APPENDIX A: NETWORKING CONNECTION............................ 17
A.1 Switch's RJ-45 Pin Assignments ................................. 17
A.2 RJ-45 cable Pin Assignments ..................................... 17
A.3 Fiber Optical Cable Connection Parameter................... 18

5
1.INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
Fast Ethernet Switch x 1
User's manual x 1
Power cord x 1
Rubber feet x 4
If any of these are missing or damaged, please contact your
dealer immediately, if possible, retain the carton including the
original packing material, and use them against to repack the
product in case there is a need to return it to us for repair.
1.2 How to Use This Manual
This Fast Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Switch.
Chapter 3 Switch operation
The chapter explains the Fast Ethernet Switch transmit
operation.
Chapter 4 Troubleshooting
The chapter explains the troubleshooting of the Fast Ethernet
Switch.
Appendix A
This chapter contains cable information of the Fast Ethernet
Switch.
l
l
l
l

6
1.3 Product Features
Complies with the IEEE 802.3 Ethernet and IEEE 802.3u Fast
Ethernet standard
Features Store-and-Forward mode with wire-speed ltering
and forwarding rates
Support 2K MAC address table
Support to handle up to 1522 bytes packet size
LED indicators for simple diagnostics and management
Hardware based 10/100Mbps auto-negotiation
Full / Half-Duplex capability on every TX ports, total band-
width is up to 200Mbps per port
IEEE 802.3x PAUSE frame ow control for full duplex opera-
tion
Backpressure ow control for half duplex operation
One shared 100Base-FX interface for up to 2km (multi-mode
ber 50/125µm) on FSD-805SC / FSD-805ST
One shared 100Base-FX interface for up to 15km (single-
mode ber 9/125µm) on FSD-805S15
Automatic source address learning and aging
Internal power adapter 100-240V AC, 50/60Hz, 0.2A
FCC, CE class A compliant
l
l
l
l
l
l
l
l
l
l
l
l
l
l

7
1.4 Product Specications
Product FSD-805 FSD-805SC FSD-805ST FSD-805S15
Hardware Specication
10/100Base-TX Ports 8 8 8 8
100Base-FX SC Port - 1 1
100Base-FX ST Port - - 1 -
Dimensions (W x D x H) 191 mm x 85 mm x 26 mm
Weight 325g
Power Requirement Internal power 100-240V AC, 50/60Hz, 0.2A
Power Consumption / Dissipation 4.3 watts / 14.6 BTU
Switch Specication
Switch Processing Scheme Store-and-Forward
Address Table 2K entries
Share data Buffer 1Mbit on-chip frame buffer
Flow Control Back pressure for half duplex, IEEE 802.3x Pause
Frame for full duplex
Switch fabric 1.6Gbps
Throughput (packet per second) 11.9Mpps
Network cables
10/100Base-TX:
2-Pair UTP Cat. 3, 4, 5 (100meters, max.)
EIA/TIA-568 100-ohm STP (100meters, max.)
100Base-FX:
Multi-mode optic ber 62.5/125μm, 50/125μm
(FSD-805SC / FSD-805ST. 2km, max.).
Single-mode optic ber 9/125μm
(FSD-805S15. 15km, max.)
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3x Full-duplex Flow control
Temperature Operating: 0~50 Degree C
Storage: -40~70 Degree C
Humidity Operating Operating: 5% to 90%, Storage: 5% to 90% (Non-
condensing)
Regulation Compliance FCC Part 15 Class A, CE

8
2.INSTALLATION
This section describes the functionalities of the Fast Ethernet
Switch’s components and guides how to install it on the desktop.
Basic knowledge of networking is assumed. Please read this
chapter completely before continuing.
In the following section, the term “Switch” means the Four
Switches, i.e. FSD-805, FSD-805SC / FSD-805ST and FSD-
805S15; term of “switch” can be any third part switches.
2.1 Product Description
The PLANET FSD-805 / FSD-805SC / FSD-805ST and FSD-
805S15 are 10/100Mbps Fast Ethernet Switches in a compact
housing for easily desktop placement. With 8 ports respectively
and it’s Auto-negotiation capability, all the RJ-45 ports can
be congured to speeds of 10/20Mbps or 100/200Mbps
automatically; With increasing bandwidth requirements for local
area networks, the Switch provide non-blocking wire-speed
performance and 1.6Gbps internal switching fabric, it is the ideal
option to alleviate bottlenecks in client/ server and peer-to-peer
environments in a cost-effective way.
The FSD-805SC / FSD-805ST and FDS-805S15 provide one
shared 100Base-FX port with port 1, TP / Fiber port Selection
through the DIP switch.
All RJ-45 copper interfaces support 10/100Mbps Auto-Negotiation
for optimal speed detection through RJ-45 Category 6, 5 or 5e
cables. Support is standard for Auto-MDI/MDI-X that can detect
the type of connection to any Ethernet device without requiring
special straight or crossover cables.
The Flow Control function allows your Fast Ethernet Switch
supported routers and servers to directly connect to this Switch
for fast, reliable data transfer.

9
2.1.1 Product Overview
PLANET FSD-805 / FSD-805SC / FSD-805ST and FSD-805S15
are 10/100Mbps Fast Ethernet Switch, with 8 RJ-45 10/100Mbps
ports for cost effective high-performance network connectivity.
With its 1.6Gbps non-blocking switch fabric, the Switch can
also provide a local, high bandwidth. The Switch also supports
Store-and-Forward forwarding scheme to ensure low latency and
high data integrity, eliminates unnecessary trafc and relieves
congestion on critical network paths. With an intelligent address
recognition algorithm, the Switch could recognize up to 2K
different MAC address and enables ltering and forwarding at
full wire speed.
Choice of multi-mode / single mode 100Base-FX SC / ST
interface on FSD-805SC / FSD-805ST and FSD-805S15, the ber
transmit distance can be 2km and 15km.
2.1.2 Switch Front Panel
Figure 2-1 & 2-2 & 2-3 & 2-4 shows a front panel of FSD-805 /
FSD-805SC / FSD-805ST and FSD-805S15.
Figure 2-1 FSD-805 front panel
Figure 2-2 FSD-805SC front panel
Figure 2-3 FSD-805ST front panel

10
Figure 2-4 FSD-805S15 front panel
2.1.3 LED Indicators
FSD-805 / FSD-805SC / FSD-805ST / FSD-805S15
LED Color Function
PWR Green Lit: indicate the Switch has power.
LNK/ACT Green
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the Switch is actively
sending or receiving data over that port.
2.1.4 Switch Rear Panel
Figure 2-5 shows a rear panel of FSD-805 / FSD-805SC / FSD-
805ST and FSD-805S15.
Figure 2-5 FSD-805 / FSD-805SC / FSD-805ST / FSD-805S15 rear panel
Power
Notice
1. The device is a power-required device, it means,
it will not work till it is powered. If your networks
should active all the time, please consider using
UPS (Uninterrupted Power Supply) for your
device. It will prevent you from network data
loss or network downtime.
2. In some area, installing a surge suppression
device may also help to protect your Switch from
being damaged by unregulated surge or current
to the Switch or the power adapter.