Planet WNRT-300G User manual

3G / 802.11n Wireless Portable Router
WNRT-300G
Quick Installation Guide

Table of Contents
1. Package Contents ................................................. 3
2. Physical Introduction ............................................. 4
3. Hardware Installation ............................................ 5
4. Web UI Conguration .......................................... 10
5. Further Information ............................................ 12

3
1.Package Contents
Thank you for choosing PLANET WNRT-300G, the most
convenient 3G wireless portable router. Before installing
the router, please verify the contents inside the package
box.
Portable Router Quick Guide CD-ROM
Power Adapter USB Cable Ethernet Cable Li-ion Battery
Note
If there is any item missed or damaged,
please contact the seller immediately.

4
2.Physical Introduction
Top Panel Description
Power
Wireless Connection
WPS
Battery
3G Connection
WAN/LAN
Front Panel Description
The Switch of Router
AP, and Client Modes WPS Button
Power Switch
Rear Panel Description
Power Connector
5V DC Input Reset Button
10/100Mbps WAN/LAN Port
Side Panel Description
USB Port
for 3G Modem

5
3.Hardware Installation
Note
Before you start using the portable router,
please follow the procedures below to
install and charge the battery.
Step 1: Remove the battery cover, and insert the
attached battery into the slot. Then replace
the cover back.
Step 2: Charge the battery by the attached power
adapter and USB cable.
Step 3: The red LED will be lit up. When the
battery is fully charged, the LED will be off.
Note
If you will use the WNRT-300G powered by
AC power supply for a long time, please
remove the battery from the slot and keep
it of full power in a cool and dry place.
Please follow the instructions below to activate the
WNRT-300G
Step 1: Make sure the operation mode by hardware
switch is Router Mode (default setting).
RT/Client/AP ON/OFFWPS

6
Step 2: When the battery is put into the device, turn
on the WNRT-300G.
RT/Client/AP ON/OFFWPS
Step 3: Please follow the gure below to connect
the Cable/xDSL Modem to the RJ-45 port of
WNRT-300G or connect the 3G dongle to the
USB port of WNRT-300G.
Router Mode
WNRT-300G
N
N
Laptop
Smart Phone
N
3G
Base Station
Compatible
3G Dongle
Internet
3G
3G

7
Step 4: Please use your PC to site survey the wireless
signal of WNRT-300G, and connect your PC
with it wirelessly.
*Default SSID: default
*Default Wireless Security: No Security
Note
1. When the WNRT-300G is at Router
Mode, the only RJ-45 port will act as a
WAN port. Therefore, the client devices
can only connect with WNRT-300G
wirelessly. However, if you need to
connect the computer with the WNRT-
300G by UTP cable, please switch it to
AP Mode first. And the RJ-45 port will
act as a LAN port to be able to connect
with your computer.

8
Note
2. After clicking the Connect button,
If you cannot obtain an IP address
automatically from WNRT-300G in
Router Mode, please follow the
procedures below to congure the
network connection.
Step 1. Click “Start” button located at
lower-left corner of the screen.
Step 2. Click “Control Panel”.
Step 3. Click “Network and Sharing
Center”.
Step 4. Click “Change adapter
settings”.
Step 5. Right-click “Wireless Network
Connection” or “Local Area
Connection”, and choose
“Properties”.
Step 6. Select “Internet Protocol
Version 4 (TCP/IPv4)” and
click “Properties” button.
Step 7. Select “Obtain an IP
address automatically” and
“Obtain DNS server address
automatically”, then click “OK”.

9

10
4.WebUIConguration
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Step 1: Open the Web browser and enter the default
IP address http://192.168.1.1
The default username and password are both
“admin”. Then click OK button to continue.