Playcore Dero Bike Locker User manual

© 2017 Dero
Maximum Security
The Dero Bike Locker™ is bike security at its best. Ideal for long-term parking,
its steel construction makes sure thieves stay out. Multiple locking options
and all standard powder coat color options are available. Ships flat to save
you money.
DERO BIKE LOCKER™

www.dero.com | 1-888-337-6729
© 2017 Dero
DERO BIKE LOCKER™
FINISH OPTIONS
FLOORING
LOCKING OPTIONS
CONFIGURATIONS
Galvanized
U-lock/Padlock Handle
Single-Sided
An optional perforated, galvanized steel floor is available
Keyed Lock
Double-Sided
Thermoplastic
Powder Coat
Black Light Gray
RAL 7042
Deep Red
RAL 3003
Yellow
RAL 1023
White
Blue
RAL 5005
Sky Blue
RAL 5015
Hunter Green
RAL 6005
CNH Bright Yellow Orange
RAL 2004
Light Green
RAL 6018
Green
RAL 6016
Sepia Brown
RAL 8014
Bronze Silver
9007
Dark Purple Flat Black Wine Red
RAL 3005
Beige
RAL 1001
Iron Gray
7011
Black Green Red GrayBlue Brown

© 2017 Dero
www.dero.com | 1-888-337-6729
CAPACITY 1-2 Bikes depending on configuration
MATERIALS Base: 1.5” x 14g square tube
Corners: 14g plate
Sides: 18g plate
Doors: 16g plate
Top: 18g plate
Optional Divider: 14g aluminum sheet
FINISHES Galvanized
An after fabrication hot dipped galvanized finish is our
standard option.
Powder Coat
Our powder coat finish assures a high level of adhesion and
durability by following these steps:
1. Sandblast
2. Epoxy primer electrostatically applied
3. Final thick TGIC polyester powder coat
LOAD DATA 40 psf snow, 90 mph wind exposure B, high seismic
SETBACKS Allow a 60” clearance from door face.
STANDARD
OPTIONS
• Gear hook
• Leveling feet
• Ventilating window on doors
• Grati resistant
• UV Resistant
• Numbered plates available
DERO BIKE LOCKER™
Submittal Sheet
76”
48”
40”

© 2017 Dero
www.dero.com | 1-888-337-6729
DERO LOCKER
Setbacks
60”
Allow 60” clearance
from door face.

1
www.dero.com | 1-888-337-6729
© 2017 Dero
Divider Flanges
32
Attach the corner pieces to the base with
(4) ⁄” x ¾” bolts and washers at each corner
bottom. These should be finger-tight. For lockers
with a floor option, place the floor down before
the corners.
Attach the side pieces with (7) ⁄” x ¾” bolts
and washers each. These should be finger-
tight. For double lockers, also attach the
divider flanges.
Place the locker base where the final locker position will be. Thread the leveling feet into the locker base and
adjust the feet as necessary to level the base. If the locker is being installed on asphalt, use the asphalt feet.
Once the base is level and in place, use a hammer drill with a ⁄” diameter masonry bit to drill through the
leveling feet and into the ground at least 4”. Pound the wedge anchors through the leveling feet and into the
ground and tighten the nuts.
RECOMMENDED BASE MATERIAL
Solid concrete is the best base material for installation.
To ensure the proper anchors are shipped with your
rack, ask your Dero representative which anchor is
appropriate for your application. Be sure nothing is
underneath the base material that could be damaged
by drilling.
TOOLS NEEDED
Hammer drill with ⁄” x 6+ masonry bit
Hammer
Bubble level
Tape measure
⁄”, ⁄”, ¼”, ⁄” hex L-wrench with ball end
⁄”, ½”, 1 ⁄” wrench with open end
#3 Philips screw driver
Wedge anchor
Leveling foot
Asphalt foot
DERO BIKE LOCKER™
Installation Instructions

www.dero.com | 1-888-337-6729
© 2017 Dero
DERO BIKE LOCKER™
Installation Instructions
6
4 5
Attach roof with (22) ⁄” x ¾” bolts and washers.
Check that all corners are coincident with the
base corners and tighten the ⁄” x ¾” bolts at the
bottom of the corners. Then tighten the bolts at
the top of the corners. Finally, tighten the bolts
attaching the sides and top.
For single lockers, attach the back piece with
(8) ¼” x ½” button-head bolts and toothed nuts
(use every other hole).
Attach the door with (8) ¼” x ½” flat-head
bolts and toothed nuts. These should be
very tight. Remove the pictured bolt in the
base of the corner piece and replace with the
shoulder bolt through the spring end. Hook
the other spring end through the hole in the
door lever.
Remove bolt and replace with
shoulder bolt through spring end.
Hook other end of spring through
hole in door lever.

www.dero.com | 1-888-337-6729
© 2017 Dero
DERO BIKE LOCKER™
Installation Instructions
8
10
7
9
11
Check to see that the latch bar is holding the door
shut without the door being held shut too tight or
loose. The latch bar position can be adjusted by
moving the shaft collars on the door handle and
by moving the ⁄” nuts on the lower pivot.
To install a gear hook, remove the pictured ⁄”
bolt and replace it with the hook and tighten nut.
Lockers may be further leveled by loosening the
wedge anchor nut and turning the leveling feet
with a 1 ⁄” wrench. Tighten all wedge anchors
when done.
Check to see that the latch strike is smoothly
engaging the lock. The lock position can be
moved vertically by loosening the ¼” bolts and
can be moved horizontally by loosening the ⁄”
bolts. The small lever on the upper-right corner
of the lock will manually unlock it.
For double lockers, attach the divider with
(6) ⁄” x ¾” bolts and washers. The top edge
of the divider is noted with a “T” cutout.
5/16” Nuts
Shaft Collars
Latch Bar
Strike Lock Lock Plate
Gear Hook
“T”