PMT AS7.D014.600-D User manual

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
TRIMLINE VEHICLE DOCK FOR
DURABOOK Z14 LAPTOP
Description Part Number
TrimLine Dock for Durabook Z14 Laptop, Standard,
NPT
AS7.D014.600-D
TrimLine Dock for Durabook Z14 Laptop, Standard,
TPT
AS7.D014.603-D

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
POWER:
• The power input should be 19 VDC, 65W. Use a recommended power supply
for the dock.
ACCESSORIES:
• The dock will accommodate laptop additional accessory attachments such as
extended battery.
WIRING:
• PMT does not recommend relying on a cigarette socket adaptor for powering
vehicle docks. We recommend hard wiring using a good clean ground direct
from the vehicle battery (-) post, and (+) supply from a fused 12v location also
directly from the vehicle battery. All peripherals connecting to the docking
station should get power and ground from the same location as the dock.
• Visit www.precisionmounts.com/support/installation-user-guides.html for a
copy of our general wiring and troubleshooting guide.
SERVICING [ENTRETIEN]:
• If the dock does not work as intended, please contact PMT for troubleshooting
or to schedule a service. [Si le dock ne fonctionne pas comme prévu,
contactez PMT pour le dépannage ou pour planifier un service.]
• Servicing of the dock should be only done by authorized service center
personnel. Unauthorized servicing of the dock will void its warranty.
[L'entretien du dock ne doit être effectué que par le personnel du centre de
service autorisé. Un entretien non autorisé du dock annulera sa garantie.]
GENERAL INSTRUCTIONS

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
Note: All pictures used in this guide are of triple pass thru (TPT) vehicle
dock (Part no: AS7.D014.603-D). However processes and information
relate to other variants of the same dock mentioned in previous pages
DESCRIPTION OF PARTS AND LAYOUT
Tie Bar
Rear clamp Rear guide supports
RF pass through
Docking connector
Docking pin
Front clamp
Latch
Lock

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
DESCRIPTION OF PARTS AND LAYOUT
CONTINUED - REAR VIEW
Speaker and
Microphone
Serial VGA
HDMI Display
USB 2.0(2)
USB 3.0(2)
Ethernet
Power
SMA
Antenna
Connectors
(optional)

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
DOCKING THE LAPTOP
•Step 1
Ensure that the dock is unlocked and
unlatched. If locked, insert key and rotate
lock 90 degrees counter-clockwise. To
unlatch, push the slider latch as shown in the
picture. This allows the rear clamp to spring
up to open position.
•Step 2
Align the slots on the laptop front with the
front clamp on the dock.
•Step 3
Align the rear laptop slots with the rear
supports as shown in picture.
•Step 4
Use force by hand to press the laptop to
enable the rear clamps enter the slots at the
laptop rear.
•Step 5
Ensure the rear clamp is inside the laptop
slot as shown.

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
UNDOCKING THE LAPTOP
•Step 1
Ensure that the dock is unlocked. If
locked, insert key and rotate lock
90 degrees counterclockwise.
Push the latch to unlatch and
undock the laptop.
•Step 2
The latch enables the springs to
open up and rear clamps extend
out beyond the laptop slots as
shown in the picture.

515 58th Ave SE, Calgary, Alberta, T2H 0P7
1-888-869-7652 | inf[email protected]
WWW.PRECISIONMOUNTS.COM
CABLE MANAGEMENT & MOUNTING
• Connect all cables securely to
dock ports and use tie straps
to secure cables to the
mounting bracket as shown.
The mounting bracket has
slots, so that the tie straps
can be secured at desired
location.
• Once you have attached all
cables needed to the vehicle
dock, attach the mounting
plate to the dock using the 4
supplied #10-24 UNC screws
(2 on each side).
• The standard mounting plate
that comes with the PMT Z14
laptop dock features an
industry standard VESA
75mm x 75mm bolt
pattern.This allows easy
mounting to many pre-
existing mounts as well as
dedicated mounts from PMT.
Use the supplied #¼-20
hardware for mounting.