PNI SmartHome SM400 User manual

MANUAL DE UTLIZARE
Telecomanda pentru kit casa
inteligenta PNI SmartHome SM400
Section 2 - Programming the Remote with SkylinkNet Internet Hub
1. Go to “More” and tap
on “System Settings”.
2. Tap on “Setup
Wizard”.
3. Tap on “Add Device”.
NOTE: Programming the keychain remote with the SkylinkNet Internet Hub
must be done from the SkylinkNet App.
4. Tap on “Security
Remote/Keypad”.
5. Name your Security
Keychain Remote and
tap “Continue”.
6. Tap on the “Learn Now”
button and press any button
on the keychain remote.
NOTE: You can program in total up to 4 security keychain remotes or keypads
to your M-Series Alarm System.
NOTE: The security keychain remote must be programmed in Zone 1.
1. Press the learn button on the back
of the M-Series Main Console for
3 seconds until the Zone 1 light
is ashing.
2. Press any buttons on the
keychain remote.
3. Once the keychain is programed to
the M-Series Main Console, the zone 1
LED light will be off.
LED
Learn Button
Section 3 - Operation of the Security Keychain Remote
Arm Away
Select “Arm Away” to protect your
home when you’re away. This mode
activates or triggers the alarm
after a default set of time, giving you
enough time to get in and out of
your house to arm/disarm the
alarm system.
Disarm
Select “Disarm” to
deactivate the alarm system.
Panic Button
Press and hold the Panic
Button for 3 sec. to
activate the alarm.
Arm Home
Select “Arm Home” to protect while
you’re at home. This mode deactivates
motion sensors but leaves other
sensors activated.
Section 1 - Programming the Remote with M-Series Main Console
A red led will ash when pressing any buttons on the remote.
NOTE:

1. To reset the password, press buttons 1 and 2 simultaneously and hold for
more than 15 seconds until the LED (5) ashes.
2. After you release buttons 1 and 2, the LED (5) will be turned off and the
remote will be reset back to factory default password.
NOTE: After resetting the Remote, the password feature will be disabled and the
password will change back to the factory default 2,2,2. You need to re-program
the Keychain Remote to your M-Series Main Unit or SkylinkNet Internet Hub.
1. To change the password, press buttons 1 and 3 simultaneously and hold
for at least six seconds. The LED (5) will change from ashing quickly to
ashing slowly.
2. Input the old password (factory default 2,2,2).
3. Press buttons 1 and 3 simultaneously to conrm. If the password is wrong,
the LED (5) will ash three times, and you have to restart.
4. Input the new password.
5. Press buttons 1 and 3 simultaneously to re-conrm. If the password is
incorrect, the LED (5) will ash three times, and you have to restart
this procedure.
6. The password has now been changed, and the password protection is
now enabled.
Section 5 - Changing the Keychain Remote Password
Section 4 - Using the Keychain Remote Password Function
Troubleshooting M-Series Alert/Alarm System
Solution
The M-Series Main Console
does not respond to the
remote?
- You must program the remote to the
M-Series Main Console or SkylinkNet Internet
Hub before they can work together.
- Ensure to input the correct password if
enabled the password protection.
Can I erase just one remote
from a zone?
- You need to test each remote individually.
Problem
This function allows you to enter a passcode before pressing a button
to arm, disarm or activate the panic feature.
NOTE:
The password can be 2-8 digits and can be a combination of buttons
1,2,3 and 4.
NOTE:
Warranty
ONE YEAR WARRANTY
This product is guaranteed to be free of defects in materials and
workmanship for 1 year from the date of purchase. If this product is
defective, call 1-800-304-1187 for repair or replacement parts.
Guarantee does not include normal wear and tear or batteries.
If you have any questions, problems or missing parts,
please call Skylink Customer Support:
9:00am - 5:00pm EST, Monday-Friday.
Or e-mail us at [email protected]
P/N : 101Y194 Rev:0
©2014 SKYLINK GROUP.
CUSTOMER SERVICE
17 Sheard Avenue,
Brampton, Ontario,
Canada L6Y1J3
1-800-304-1187
www.skylinkhome.com
Section 6 - Resetting the Keychain Remote Password
I have multiple remotes in
one zone and the M-Series
Main Consoles keep
ashing the LED light
indicating a remote failure.
How do I know which sensor
is having a problem?
- You must erase all the remotes/sensors and
then program the remotes/sensors you
want to keep.
When the operation range is reduced, or when the backlight LED does not
ash during operation, it is time to replace the battery.
Follow the instructions below to replace the battery:
1. Undo the screws (1) on the back of the keychain remote.
2. Pry out the back cover from the keychain remote.
3. Take out the old battery (2).
4. Place the new battery (2) in position. Beware of the polarity.
5. Close the back cover with the two screws (1).
NOTE: Dispose of old battery promptly and properly.
NOTE: The Security Keychain Remote is powered by a CR2032.
Back Cover
(2)
(1)
Leave a 1 second pause period between entering the password and
operating the garage door. The factory default password is 2,2,2. The password
setting on the remote control (A) comes disabled as per factory default.
NOTE:
1. To enable or disable the password, press buttons 1 and 3 simultaneously
and hold for at least 2 seconds until the LED (5) ashes quickly, but not
until the LED ashes slowly.
2. Input the old password. [ Factory default 2,2,2 ]
3. Press button 1 and 3 simultaneously to conrm. If the password is correct,
the password protection will be disabled/enabled.
4. To control your alarm system enter your passcode, then press the button
to control your alarm system.
If you enable the password protection, you can only
operate the keychain remote, after you input the correct password.
NOTE:
Section 7 - Replacing the Battery
4
3
2
1
A
5
4
3
2
1
5
A