Polar Electro CF760-A User manual

Model:
CF760-A / CF761-A / GG753-A
Chilled Drinks
Dispenser
Instruction manual
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 1CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 1 2023/3/7 13:352023/3/7 13:35

2
EN Telephone Helpline: 1300225960
Safety Instructions
• Position on a flat, stable surface.
• Install the appliance where it can be overseen by trained
personnel.
• Always carry, store and handle the appliance in a vertical
position.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components or service panels on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- Fire Precautions
- Wiring Regulations
- Building Regulations
• DO NOT immerse in water, or use jet/pressure washers to
clean the appliance.
• Not suitable for outdoor use.
• Always switch off and disconnect the power supply to the
appliance before cleaning.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a POLAR
agent or a recommended qualified technician in order to avoid
a hazard.
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 2CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 2 2023/3/7 13:352023/3/7 13:35

3
AUEN
Telephone Helpline: 1300225960
• Polar recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Earth Continuity, Insulation Continuity and
Functional Testing.
Caution: Risk of Fire
• Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of
obstruction. Unit should not be boxed in without
adequate ventilation.
• Warning: Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food
storage compartments of the appliance.
Product Description
CF760-A - Single Chilled Drinks Dispenser CF761-A - Double Chilled Drinks Dispenser
GG753-A - Triple Tank Chilled Drinks Dispenser
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this machine will provide the best possible performance from your POLAR product.
Pack Contents
The following is included:
• Polar Chilled Drinks Dispenser
• Tank, tank Gasket & Lid (CF760-A x 1, CF761-A x 2, GG753-A x 3)
• Tap Assembly (CF760-A x 1, CF761-A x 2, GG753-A x 3)
• Spare Tank Gasket and O-ring (CF760-A x 1, CF761-A x 2, GG753-A x 3)
• Instruction Manual
• Mixing Paddle (CF760-A x 1, CF761-A x 2, GG753-A x 3)
• Drip Tray (CF760-A x 1, CF761-A x 2, GG753-A x 3)
POLAR prides itself on quality and service, ensuring that at the time of unpacking the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your POLAR dealer immediately.
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 3CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 3 2023/3/7 13:352023/3/7 13:35

4
EN Telephone Helpline: 1300225960
Installation
Note: Not for use in vans or trailers, food
trucks or similar vehicles.
If the unit has not been stored or moved in
an upright position, let it stand upright for
approximately 12 hours before operation.
If in doubt allow to stand.
1. Remove the appliance from the packaging and
remove the protective film from all surfaces.
2. When positioning the dispenser, maintain
a distance of 20cm (7 inches) between the
appliance and walls or other objects for
ventilation. Increase this distance if the
obstacle is a heat source.
3. If necessary, adjust the screw legs of the
dispenser to stabilise it.
Assembly/Disassembly
1. Insert the large rubber gasket into the bottom
of the tank [Fig. 1].
1
2. Holding the top and bottom of the tap lever,
gently bend the lever in the middle [Fig. 2].
3. Push the two hooks at the back of the tap lever
into the slot in the front of the tank and drop
into place [Fig. 3].
4. Lower the tank on to the cooling column.
Locate the four feet on the bottom of the tank
to the mounts on top of the cooling unit.
Note: Lubricate the gasket with
a small amount of water if the
gasket is too tight.
2
Hooks
3
Tank
Front Lever
Slot
5. Roll the O-ring down
the tap shaft [Fig. 4]
and insert thin end
first into the hole in
the tank.
6. Ensure the bottom
of the tap slots into
the gap in the tap
lever.
4
7. Hang the drip tray from the slots on the front
of dispenser [Fig. 5].
5
8. Securely fix the lid to the tank.
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 4CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 4 2023/3/7 13:352023/3/7 13:35

5
AUEN
Telephone Helpline: 1300225960
Operation
Filling
1. Switch Off the dispenser.
2. Remove the lid and pour the liquid into the
tank.
3. Replace the lid.
WARNING: Do not fill the tank
with hot liquid.
Do not let the level exceed the
‘MAX’ level line displayed on the
front of the tank.
Note: CF761-A/GG753-A Only -
If only one tank is to be filled,
it must be the left tank. To use
left tank only, you just need to
switch left stirring switch ON
(I position). Meanwhile, the
right tank does not chill and the
paddle does not run.
Using the Dispenser
1. Turn On the
Power switch
on the side of
the dispenser.
2. Switch the
stirring switch
to the ‘On’
position [I].
7
Model: CF761-A
3. Once the liquid is sufficiently cooled, push the
receptacle against the tap lever to dispense the
liquid.
Note: Should the paddle
encounter any resistance in the
liquid, it will reverse direction.
Adjusting the Beverage tank
temperature
To adjust the temperature of beverage tank(s), lift
up the plastic cover(s).
As CF761-A/GG753-A has more than one tank,
Tank 1 is the one on the left hand side of the unit
when looking from the front.
1. Turn on the main switch on the right hand
of the unit. The power indicator light (A)
illuminates on the controller.
C
8
2. To set the temperature of Tank 1, press
button twice. The indicator light (1) on the top
will illuminate and the current temperature will
flash. Press the arrow buttons ( , ) to
set the desired temperature. Then press
button to confirm. (Temp range: 0°C - 10°C)
3. Repeat above operations to set the temperature
of tank 2/3, if desired (for CF761-A/GG753-A).
4. During use, the unit will automatically display
the actual temperature of the tank for 2
seconds, with the corresponding tank indicator
light illuminating.
5. To switch off the cooling of a certain tank,
press the corresponding tank button for 3
seconds. “OFF” will be displayed. To switch on
cooling, press and hold the tank button again.
Emptying the Dispenser
Drain the dispenser by using the tap lever(s) to
empty the tank(s).
Note: Do not drain the dispenser
by tipping the appliance.
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 5CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 5 2023/3/7 13:352023/3/7 13:35

6
EN Telephone Helpline: 1300225960
Cleaning, Care & Maintenance
• Switch off and disconnect from the power supply before cleaning.
• Warm, soapy water is recommended for cleaning. Cleaning agents may leave harmful residues. DO
NOT wash the base unit, instead wipe the exterior with a damp cloth.
• Empty and clean the drip trays regularly.
• Unit should be de-scaled regularly. Note that scale may cause premature failure of the machine and it
could invalidate your warranty.
Cleaning the Condenser
POLAR recommend the condenser is cleaned at least once a month.
Note: The condenser is the black (CF760-A) or silver (CF761-A/GG753-A) metal
grid behind the side panel.
To clean the condenser:
1. Unscrew the two screws from beneath the Temperature controller side panel.
2. Lift the side panel up and over Temperature controller to remove.
3. Clean the condenser with a soft cloth or brush.
WARNING: Take care when cleaning the condenser; sharp edges may cut.
4. Replace the panel and two screws.
Troubleshooting
A qualified technician must carry out repairs if required.
Fault Probable Cause Solution
The appliance is not
working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or power cord is damaged Replace plug or lead
Mains power supply fault Check mains power supply
The dispenser is not
cooling
Coolant leak Consult a qualified technician
Fan motor failed Consult a qualified technician
Airflow obstructed to the
condenser
Increase the gap between appliance and
obstacles/heat source
Condenser is clogged Remove side panels and clean condenser
The mixing paddles are
not working
Mixing motor has failed Consult a qualified technician
The tank is leaking Gasket problem Check the gaskets and replace if necessary
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 6CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 6 2023/3/7 13:352023/3/7 13:35

7
AUEN
Telephone Helpline: 1300225960
Technical Specifications
Note: Due to our continuing program of research and development, the specifications herein may be
subject to change without notice.
Model Voltage Power
(W)
Current
(A) Tanks Capacity (litres) Refrigerant Dimensions H x W x D mm
Weight
(kg)
CF760-A 220-240V~ 50Hz 290W 1.9A 1 12 R290 635 x 220 x 450 20
CF761-A 220-240V~ 50Hz 370W 2.2A 2 24 R290 635 x 420 x 450 28
GG753-A 220-240V~ 50Hz 450W 2.55A 3 36 R290 635 x 650 x 450 36
Electrical Wiring
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
The appliances must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and environmentally safe
recycling process. For further information on how to dispose of this product correctly, contact the product
supplier, or the local authority responsible for waste disposal in your area.
POLAR parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal authorities.
POLAR products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to
change specifications without notice.
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 7CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 7 2023/3/7 13:352023/3/7 13:35

DECLARATION OF CONFORMITY
• Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
• Declaración de conformidad
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo
Model • Modèle • Modell • Modello
• Modelo
G-Series Chilled Drinks Dispenser
G-Series Twin Tank Chilled Drinks Dispenser
G-Series Triple Tank Chilled Drinks Dispenser
CF760 (-E & -A)
CF761 (-E & -A)
GG753 (-E & -A)
Application of Territory Legislation
& Council Directives(s)
Toepassing van Europese
Richtlijn(en) • Application de la/des
directive(s) du Conseil • Anwendbare
EU-Richtlinie(n) • Applicazione delle
Direttive
• Aplicación de la(s) directiva(s) del
consejo
Machinery Directive 2006/42/EC
Supply of Machinery (Safety) Regulations 2008
(BS) EN 60335-1:2012 +A11:2014 +A13:2017
+A1:2019 +A14:2019
(BS) EN 60335-2-75:2004 +A1:2005 +A11:2006
+A2:2008 +A12:2010
(BS) EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive
2014/30/EU - recast of 2004/108/EC
Electromagnetic Compatibility Regulations 2016
(S.I. 2016/1091)
(BS) EN IEC 55014-1:2021
(BS) EN IEC 55014-2:2021
(BS) EN IEC 61000-3-2:2019 +A1:2021
(BS) EN 61000-3-3:2013 +A1:2019 +A2:2021
Restriction of Hazardous Substances Directive
(RoHS) 2015/863 amending Annex II to Directive
2011/65/EU
Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic
Equipment Regulations 2012 (S.I. 2012/3032)
Electrical Safety
IEC 60335-1:2010 +A1:2013
+A2:2016
IEC 60335-2-75:2012 +A1:2015
EN 62233:2008
Electromagnetic Compatibility
AS/NZS CISPR 14.1:2021
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produttore • Nombre del fabricante
Polar
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s)
and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande
Richtlijn(en) en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und
Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y
estándar(es) arriba mencionadas.
Date • Data • Date • Datum • Data •
Fecha • Data
18th January 2023
Signature • Handtekening •
Signature • Unterschrift Firma •
Firma
Full Name • Volledige naam • Nom
et prénom • Vollständiger Name •
Nome completo • Nombre completo
Ashley Hooper
Eoghan Donnellan
Brendan Denmeade
Position • Functie • Fonction •
Position • Qualifica • Posición
Technical & Quality
Manager
Commercial Manager/
Importer
Commercial Manager/ Responsible
Supplier
Producer Address • Adres fabrikant •
Adresse du producteur • Anschrift
des Herstellers • Indirizzo del
produttore • Dirección del fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
Unit 9003,
Blarney Business Park,
Blarney,
Co. Cork
Ireland
15 Bagdally Road,
Campbelltown
NSW 2560
DocuSign Envelope ID: 0D93B51E-4795-43B8-9B38-7D799E4EB2AA
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 8CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 8 2023/3/7 13:352023/3/7 13:35

CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 9CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 9 2023/3/7 13:352023/3/7 13:35

CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 10CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 10 2023/3/7 13:352023/3/7 13:35

CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 11CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 11 2023/3/7 13:352023/3/7 13:35

CF760-A_CF761-A_GG753-A_A5_v6_2023/03/07
http://www.polar-refrigerator.com/
CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 12CF760-A_CF761-A_GG753-A_A5_v6_20230307.indb 12 2023/3/7 13:352023/3/7 13:35