Polar Electro GE632 User manual

Model:
GE632/GE633
Beer
Dispenser
Instruction manual
GE632-GE633_UK_A5_v1_20210419.indb 1GE632-GE633_UK_A5_v1_20210419.indb 1 2021/4/19 16:072021/4/19 16:07

2
UK
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components or service panels on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use the appliance outside.
• DO NOT store food in the appliance.
• DO NOT use this appliance to store medical supplies.
• DO NOT allow oil or fat to come into contact with the plastic
components or door seal. Clean immediately if contact occurs.
• DO NOT store products on top of the appliance.
• Always carry, store and handle the appliance in a vertical
position and move by holding the base of the appliance.
• Always switch off and disconnect the power supply to the unit
before cleaning.
• Keep all packaging away from children. Dispose of the packaging
in accordance with the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a POLAR
agent or a recommended qualified technician in order to avoid
a hazard.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
GE632-GE633_UK_A5_v1_20210419.indb 2GE632-GE633_UK_A5_v1_20210419.indb 2 2021/4/19 16:072021/4/19 16:07

3
UK
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Keep the appliance and its cord out of reach of children less
than 8 years.
• The appliance is not intended to be operated by means of an
external timer or separate remote-control system.
• Polar recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Earth Continuity, Insulation Continuity and
Functional Testing.
• POLAR recommend that this product is connected to a circuit
protected by an appropriate RCD (Residual Current Device).
Caution Risk of Fire
• Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of
obstruction. Unit should not be boxed in without
adequate ventilation.
• Warning: Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food
storage compartments of the appliance, unless they are the
type recommended by the manufacturer.
Product Description
GE632 - Direct Draw Beer Dispenser (1 Keg 1 Tap)
GE633 - Direct Draw Beer Dispenser (2 Keg 2 Tap)
GE632-GE633_UK_A5_v1_20210419.indb 3GE632-GE633_UK_A5_v1_20210419.indb 3 2021/4/19 16:072021/4/19 16:07

4
UK
Introduction
Please take a few moments to carefully read
through this manual. Correct maintenance and
operation of this machine will provide the best
possible performance from your POLAR product.
Pack Contents
The following is included:
• Beer Dispenser
• Drip pan
• Beer tower assembly
• CO2line
• Tee joint for CO2 lines
• Screws and washers
• Multi-function spanner
• Instruction manual
POLAR prides itself on quality and service, ensuring
that at the time of packaging the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit,
please contact your POLAR dealer immediately.
Installation
Note: If the unit has not been
stored or moved in an upright
position, let it stand upright for
approximately 12 hours before
operation. If in doubt allow to
stand.
1. Remove the appliance from the packaging.
Make sure that all protective plastic film and
coatings are thoroughly removed from all
surfaces.
2. To optimize performance and longevity, ensure
a minimum clearance of 2.5cm is maintained
between the unit and walls and other objects,
with a minimum 5cm clearance on the top.
NEVER LOCATE NEXT TO A HEAT SOURCE.
Note: Before using the appliance
for the first time, clean the
interior with soapy water.
Location
• The appliance is intended for indoor use only.
• Be sure the location chosen has a floor strong
enough to support the total weight of the
cabinet and contents. A fully loaded unit can
weigh as much as 450kg. Reinforce the floor as
necessary to provide maximum loading.
• For the most efficient refrigeration, be sure to
provide good air circulation inside and outside.
Ventilation
• Be sure that the unit has access to ample air.
Avoid hot corners and locations near stoves
and ovens.
• Should it become necessary to lay the unit
on its side or back for any reason, allow at
least 12 hours before start-up so as to allow
compressor oil to flow back to the sump.
Failure to meet this requirement can cause
compressor failure and unit damage.
Levelling
• A level cabinet will perform better because the
doors will line up with the frames properly, the
cabinet will not be subject to undue strain and
the contents inside the cabinet will not move
around.
• Use a level to make sure the unit is level from
front to back and side to side.
• Units supplied with legs will have adjustable
bullet feet to make the necessary adjustments.
If the unit is supplied with castors, set the
brakes on the castors to keep the appliance in
position.
• Ensure the floor where the unit is to be located
is level.
Caution:
Failure to follow all the due
installation instructions will
invalidate your guarantee.
GE632-GE633_UK_A5_v1_20210419.indb 4GE632-GE633_UK_A5_v1_20210419.indb 4 2021/4/19 16:072021/4/19 16:07

5
UK
Connection
Connecting the beer tower
1. Pull out the air conduct hose from the hole in
the cabinet surface.
2. Unscrew the 2 bolts to release the cover plate
which is located on the cabinet’s inner surface.
Bolt
Cover plate
3. Thread the big black washer through the beer
line that is coming from the beer tower.
Beer line
Black
Washer
Beer tower
4. Insert the beer line into the cabinet via the
hole. Then insert the air conduct hose into the
beer tower.
Air conduct hose
Beer line
Beer tower
5. Align all holes and install the 4 screws to fix
the beer tower in place.
6. Slide the beer tower’s shade downward fully.
7. Re-attach and fix the cover plate to the
cabinet’s inner surface with bolts.
Bolt
Cover plate
Beer hose
GE632-GE633_UK_A5_v1_20210419.indb 5GE632-GE633_UK_A5_v1_20210419.indb 5 2021/4/19 16:072021/4/19 16:07

6
UK
8. In case the beer tower is not stable, you can adjust the tap as needed. Open the top cap of the beer
tower first. Then use the supplied spanner to adjust the tap.
Spanner
Connecting the CO2 cylinder and beer keg
Note: The diagram below is for reference only. For actual connections, please
follow the manufacturer’s instructions supplied with the CO2cylinder and beer
keg. All connections should be done by professionals only.
Be gentle when locating CO2cylinder and beer keg into the cabinet to avoid any
damage.
1.
2.
3.
4.
5.
Beer keg
Keg tap
Beer line
Beer tower
CO2line
6.
7.
8.
9.
10.
Tee Joint for CO2lines
CO2regulator
CO2cylinder
CO2line (#1)
CO2line (#2)
GE632-GE633_UK_A5_v1_20210419.indb 6GE632-GE633_UK_A5_v1_20210419.indb 6 2021/4/19 16:072021/4/19 16:07

7
UK
Warning:
• Make sure that all fittings in system
are tight. Always keep the CO2cylinder
in vertical position. The recommended
pressure for the CO2system is 8-10 psi.
• Always handle the CO2cylinder with
care. Never lay flat or drop!
• Handle all pressure system components
with care. Do not use excessive
pressures. Be sure instructions are
understood thoroughly. If in doubt,
contact your dealer/distributor for
explanation.
• Filled CO2cylinders are potentially
dangerous because of the pressure they
contain. If you are unfamiliar with their
use or the use of the CO2regulator, seek
information from your local distributor,
or your local beverage man before
proceeding.
When necessary to connect
a remote CO2cylinder, use
below diagram for reference.
For actual connections, ensure
to follow the manufacturer’s
instructions supplied with the
CO2cylinder.
Beer keg layout: Model GE632
Beer keg layout: Model GE633
GE632-GE633_UK_A5_v1_20210419.indb 7GE632-GE633_UK_A5_v1_20210419.indb 7 2021/4/19 16:072021/4/19 16:07

8
UK
Beer keg layout: Model GE633 Operation
Control Panel
For GE632: The control panel is located on the rear
wall inside the cabinet.
For GE633: The control panel is located on the
front of the appliance.
To lock/unlock the keyboard, press and
together for more than 3 seconds. Display will flash
POF (locked) / PON (unlocked).
Turn On
1. Close the door(s) of the appliance.
2. Connect the appliance to a mains power
supply.
Set the Operating Temperature
1. Hold the SET button for 3 seconds. The value
of the current set point will be displayed.
2. Press the or button to display the
required temperature.
3. Press the SET button to store the temperature.
Manual Defrost
Press and hold the defrost button for 2 seconds
to begin a manual defrost. The defrost light
illuminates.
Lock/Unlock the Doors
Use the keys provided to lock/unlock the door.
GE632-GE633_UK_A5_v1_20210419.indb 8GE632-GE633_UK_A5_v1_20210419.indb 8 2021/4/19 16:072021/4/19 16:07

9
UK
Serving
• Before serving, ensure to locate the drip tray(s)
in place.
• Pull the tap toward you to begin pouring.
• Raise the tap handle to close the tap.
Cleaning, Care &
Maintenance
Switch off and disconnect
from the power supply before
cleaning and maintenance.
• Warm, soapy water is recommended for
cleaning. Cleaning agents may leave harmful
residues. Wipe the exterior with a damp cloth.
• Empty and clean the drip trays regularly.
• A POLAR agent or qualified technician should
carry out repairs if required.
Cleaning the cabinet
The interior and exterior can be cleaned using
soap and warm water. If this is not sufficient,
try ammonia and water or a non-abrasive liquid
cleaner. When cleaning the exterior, always rub
with the “grain” of the stainless steel to avoid
marring the finish.
Do not use an abrasive cleaner because it will
scratch the stainless steel and plastic and can
damage the breaker strips and gaskets.
Cleaning the Condenser Coil
The condenser coil requires regular cleaning, with
the recommended frequency of every 90 days.
In some instances, you may find there is a large
amount of debris and dust or grease accumulated
prior to the 90-day period. Thus the condenser coil
should be cleaned more frequently.
If the buildup on the coil consists of only light dust
and debris the condenser coil can be cleaned with
a simple brush. Heavier dust buildup may require
a vacuum or even compressed air to blow through
the condenser coil.
If heavy grease is present, there are de-greasing
agents available for refrigeration use and
specifically for the condenser coils. The condenser
coil may require a spray with the de-greasing agent
and then blown through with compressed air.
Failure to maintain a clean condenser coil can
initially cause high temperatures and excessive run
times, continuous operation with dirty or clogged
condenser coils can result in compressor failures.
Neglecting the condenser coil cleaning procedures
will void any warranties associated with the
compressor or cost to replace the compressor.
In order to maintain proper refrigeration
performance, the condenser fins must be
cleaned of dust, dirt and grease regularly. It is
recommended that this be done at least every 3
months. If conditions are such that the condenser
is totally blocked, the frequency of cleaning
should be increased. Clean the condenser with a
vacuum cleaner or stiff brush. If extremely dirty, a
commercially available condenser cleaner may be
required.
Stainless Steel Care
To maintain the stainless steel exterior of your Polar
item, please consider the following information:
Never:
• Use abrasive Scourers or scrubbing pads, etc.
• Use Chlorinated or acidic detergents
• Allow anything e.g. food, dirt, cleaning
chemicals to remain on the surface for longer
than necessary, clean them off right away.
• Allow the surface to remain wet.
Do:
• Clean often.
• Use soft Cloths or plastic Scourers.
• Rub with the grain of the metal, rather than
across it.
• Use detergents and polish designed for
cleaning Stainless Steel.
• Ensure that the cleaning products are washed
off fully and that the steel is left dry.
GE632-GE633_UK_A5_v1_20210419.indb 9GE632-GE633_UK_A5_v1_20210419.indb 9 2021/4/19 16:072021/4/19 16:07

10
UK
Gasket Maintenance
Gaskets require regular cleaning to prevent mould and mildew buildup and also to keep the elasticity of
the gasket.
Gasket cleaning can be done with the use of warm soapy water. Avoid full strength cleaning products on
gaskets as this can cause them to become brittle and prevent proper seals. Also, never use sharp tools or
knives to scrape or clean the gasket which could possibly tear the gasket and rip the bellows.
Gaskets can easily be replaced and do not require the use of tools or authorized service persons. The
gaskets are “Dart” style and can be pulled out of the grove in the door and new gaskets can be “pressed”
back into place.
Doors/Hinges
Over time and with heavy use, doors the hinges may become loose. If it is noticed that the door is
beginning to sag, it may become necessary to tighten the screws that mount the hinge brackets to the
frame of the unit. If the doors are loose or sagging this can cause the hinge to pull out of the frame
which may damage both the doors and the door hinges. In some cases this can require qualified service
agents or maintenance personnel.
Drain Maintenance
Each unit has a drain located inside the unit which removes the condensation from the evaporator coil
and evaporates it at an external condensate evaporator pan. The drain may become loose or even
disconnected resulting from moving or bumping the drain.
If you notice excessive water accumulation on the inside of the unit, be sure the drain tube is connected
from the evaporator housing to the condensate evaporator drain pan.
If water is collected underneath the unit, you may need to check the condensate evaporator drain tube to
make sure it is still located inside the drain pan.
The levelling of the unit is important as the units are designed to drain properly when on a level
surface. If your floor is not level this can also cause drain problems. Make sure all drain lines are free of
obstructions, or blocked drain lines will cause water to back up and overflow the drain pans.
GE632-GE633_UK_A5_v1_20210419.indb 10GE632-GE633_UK_A5_v1_20210419.indb 10 2021/4/19 16:072021/4/19 16:07

11
UK
Troubleshooting
Fault Probable Cause Solution
The appliance is not
working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug or lead is damaged Call POLAR agent or qualified Technician
Fuse in the plug has blown Replace the fuse
Power supply Check power supply
Cabinet temperature is
too Warm
Doors are not shut properly Check doors are shut and seals are not
damaged
Appliance is located near a
heat source or air flow to the
condenser is being interrupted
Move the appliance to a more suitable
location
Ambient temperature is too high Increase ventilation or move appliance to a
cooler position
Insufficient airflow to the fans Remove any blockages to the fans
The set temperature is too high Set a lower temperature
Low refrigerant level Call POLAR agent or qualified Technician
Condensation on the
Cabinet and/or floor
Gasket not sealing well Clean, repair, or replace the gasket as
necessary
Technical Specifications
Model Voltage Power Current Temperature
Range Refrigerant Dimensions H x W x D mm
Weight
(kg)
GE632 230V~ 50Hz 150W 1.1A 2°C ~ 8°C R600a (55g) 1312 x 612 x
810
63
GE633 230V~ 50Hz 250W 1.6A 2°C ~ 8°C R290 (95g) 1438 x 1247 x
620
97
GE632-GE633_UK_A5_v1_20210419.indb 11GE632-GE633_UK_A5_v1_20210419.indb 11 2021/4/19 16:072021/4/19 16:07

12
UK
Electrical Wiring
POLAR appliances are supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
POLAR appliances are wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Disposal
EU regulations require refrigeration product to be disposed of by specialist companies who remove or
recycle all gasses, metal and plastic components.
Consult your local waste collection authority regarding disposal of your appliance. Local authorities are
not obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to
dispose of the equipment locally.
Alternatively call the POLAR helpline for details of national disposal companies within the EU.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible for
waste disposal in your area.
POLAR parts have undergone strict product testing in order to comply with
regulatory standards and specifications set by international, independent,
and federal authorities.
POLAR products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to
change specifications without notice.
GE632-GE633_UK_A5_v1_20210419.indb 12GE632-GE633_UK_A5_v1_20210419.indb 12 2021/4/19 16:072021/4/19 16:07

DECLARATION OF CONFORMITY
• Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
• Declaración de conformidad • Declaração de conformidade
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento
Model • Modèle • Modell • Modello
• Modelo • Malli
Direct Draw Beer Dispenser (1 Keg, 1 Tap)
Direct Draw Beer Dispenser (2 Keg, 2 Tap)
GE632 (-E & -A)
GE633 (-E & -A)
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en) •
Application de la/des directive(s) du
Conseil • Anwendbare EU-Richtlinie(n)
• Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo • Aplicação de directiva(s) do
Conselho
Machinery Directive 2006/42/EC
Supply of Machinery (Safety) Regulations 2008
EN 60335-1:2012 +A11:2014 +A13:2017
EN 60335-2-89:2010 +A1:2016 +A2:2017
EN 62233:2008
Electro-Magnetic Compatibility (EMC) Directive
2014/30/EU - recast of 2004/108/EC
Electromagnetic Compatibility Regulations 2016
(S.I. 2016/1091)
EN 55014-1: 2017
EN55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3:2013
Restriction of Hazardous Substances Directive
(RoHS) 2015/863 amending Annex II to Directive
2011/65/EU
Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic
Equipment Regulations 2012 (S.I. 2012/3032)
Electrical Safety
IEC 60335-1:2010
IEC 60335-2-89:2010
EN 62233:2008
Electromagnetic Compatibility
EN 55014-1: 2017
EN55014-2:2015
EN 61000-3-2: 2014
EN 61000-3-3:2013
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produttore • Nombre del fabricante • Nome do fabricante
Polar
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and
Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn(en) en
Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es) arriba
mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es) Directiva(s) e
Norma(s)
Date • Data • Date • Datum • Data •
Fecha • Data
4th March 2021
Signature • Handtekening •
Signature • Unterschrift Firma •
Firma • Assinatura
Full Name • Volledige naam • Nom
et prénom • Vollständiger Name •
Nome completo • Nombre completo
• Nome por extenso
Ashley Hooper
Eoghan Donnellan
Josie Holt
Position • Functie • Fonction •
Position • Qualifica • Posición •
Função
Technical & Quality
Manager
Commercial
Manager/ Importer
Commercial Manager/ Responsible
Supplier
Producer Address • Adres fabrikant •
Adresse du producteur • Anschrift
des Herstellers • Indirizzo del
produttore • Dirección del fabricante
• Morada do fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
42 North Point
Business Park
New Mallow Road
Cork
Ireland
15 Bagdally Road,
Campbelltown
NSW 2560
DocuSign Envelope ID: 078D50A1-9FDA-4B71-B961-A3068D79EA34
GE632-GE633_UK_A5_v1_20210419.indb 13GE632-GE633_UK_A5_v1_20210419.indb 13 2021/4/19 16:072021/4/19 16:07

UK
[phone]
Eire
NL 040 – 2628080
FR 01 60 34 28 80
BE-NL 0800-29129
BE-FR 0800-29229
DE 0800 – 1860806
IT N/A
ES 901-100 133
PT [email protected]
GE632-GE633_UK_A5_v1_20210419.indb 14GE632-GE633_UK_A5_v1_20210419.indb 14 2021/4/19 16:072021/4/19 16:07

GE632-GE633_UK_A5_v1_20210419.indb 15GE632-GE633_UK_A5_v1_20210419.indb 15 2021/4/19 16:072021/4/19 16:07

GE632-GE633_UK_A5_v1_20210419
http://www.polar-refrigerator.com/
GE632-GE633_UK_A5_v1_20210419.indb 16GE632-GE633_UK_A5_v1_20210419.indb 16 2021/4/19 16:072021/4/19 16:07