Polaris Communications soundshield BT User manual
TM
Optional
Accessories
Charging Stand
B
USB Charging Cable SSBT Dongle
Binaural
Headset
Headset Hanger
Monaural
Headset
OR
What’s inside
Positioning the
microphone
gently bend the
boom and position
it to suit the curve
of your face.
Holding the
headset, rotate the
headband to bring
the boom close to
your cheek.
The ideal
placement for the
microphone is at
the corner of your
mouth, an inch
from your face.
Do not pull on the microphone boom to remove it from the headband.
To detach the microphone boom
arm from the headband, gently
push the microphone speaker from
inside the ear cushion. This will pop
the microphone boom away from
the headband.
how to wear
•If the headset has been
out of use for some time,
it may take up to 2 hours
to fully charge.
• Normal charging time
is 2-3 hours.
•Low battery is indicated
by the flashing red LED
on the headset.
LED Indicator
Multifunction Button
Power On/Off
Answer/End call
USB charging
Volume/ Pairing
Button
Mute/Pairing
Speaker Volume
HEADSET CONTROLS
PAIRING
•Plug the dongle into a USB socket on your
device.
•Press and hold the dongle LED button for more
than 3 seconds until the dongle enters pairing
mode and the led indicator starts blinking.
•Press and hold the Multifunction button on your
headset to enter pairing mode.
•When both devices are in pairing mode, the
connection will be stablished automatically and
the headset will announce the successful
connection through a voice prompt.
The pairing mode is active for 1minute and 20
seconds. After that, the dongle will enter
standby mode.
USB Type A male
connector
LED Indicator
Button
DONGLE CONNECTION
TURN OFF
While the headset is
on press and hold the
multifunction button
for 3 seconds.
•Turn on Bluetooth on your phone.
•Place the headset on your head
while it is switched off.
•Press and hold the multifunction
button for 7 seconds until the
headset beeps and the LED indicator
starts flashing rapidly.
•Search for Bluetooth devices on your
phone and connect to >>SSBT<<.
•Blue LED is On and ‘Pairing done,
Connected’ is heard in the speaker
when pairing is completed.
To unpair hold volume button down
for 2 seconds to unpair.
TURN ON
Hold the
multifunction
button for 2
seconds.
PAIRING
connect PHONE
ANSWER > Press the multifunction button
briefly.
REJECT > Press the multifunction button for
1 sec while incoming call, ‘Call rejected’ is
heard in speaker.
MAKE > Dial the number on the mobile phone
and press the multifunction button briefly.
END > Press the multifunction button briefly
or end the call on the mobile phone.
RE-DIALING > Press the multifunction button
briefly twice until you can hear ‘Re-Dialing’
from speaker.
To mute/unmute press the volume button.
CALLS
SKIP BACK > press and
hold the volume minus
(-) button.
SKIP A SONG > press
and hold the volume
plus (+) button.
music controls
To attach the
microphone boom arm to
the headband, align the
triangle shape on the
microphone boom arm
with the triangle shape on
the headband and push to
click into place. The
microphone boom arm
will then rotate to your
required position.
Attaching the headband
Button 2
Button 1
Button3
Button 4
key table
• Check that the headset is charged, turned on
and within 10 meters of the phone/dongle.
• Check that Bluetooth is switched on your
phone.
• Check that the headset is listed as a headset
device in your phone and also connected. You
may need to re-connect to the headset.
• Try removing the headset from the phone, then
pair and connect again.
problems connecting
the headset
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference
received, including interference that may cause undesired operation. This equipment has been tested
and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference, the user is
encouraged to try to correct the interference by consulting with a dealer or an experienced technician
for technical assistance. Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void user’s authority to operate the equipment.
WARNING & SAFETY INFORMATION
The antenna(s) used for this device must be installed to provide a separation distance of at least 20cm
from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
FCC Information
TM
Polaris Head Office
393 Flemington Road
North MelbourneVIC 3051 AUS
PH: 1800 626 505
FAX: 1800 079 036
2020 Polaris Communications Pty Ltd
For warranty policies and terms and conditions please visit
www.polaris.com.au/terms-conditions/
Table of contents
Other Polaris Communications Headset manuals
