Polaris P91 User manual

H0351312 Rev A
OWNER’S MANUAL
ENGLISH |FRANÇAIS |
AVERTISSEMENT
POUR VOTRE SÉCURITÉ – Pour toute opération autre que l’entretien de routine et la maintenance décrite
dans ce manuel, ce produit doit être pris en charge par une entreprise qui est autorisée et qualifiée pour
la réparation des équipements de piscine par la juridiction où le dit produit est installé lorsque de telles
exigences locales ou provinciales sont édictées. Si aucune exigence locale ou provinciale n’est disponible,
l’agent d’entretien doit être un professionnel avec suffisamment d’expérience dans l’installation et la
maintenance d’équipement de piscine pour appliquer correctement les consignes du présent manuel.
L’installation ou l’utilisation inappropriée annulera la garantie.
WARNING
FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this
manual, this product must be serviced by a contractor who is licensed and qualified in pool equipment
by the jurisdiction in which the product will be installed where such state or local requirements exist. In
the event no such state or local requirement exists, the maintainer must be a professional with sufficient
experience in pool equipment installation and maintenance so that all of the instructions in this manual can
be followed exactly. Improper installation and/or operation will void the warranty.
P91

THANK YOU FOR PURCHASING THE POLARIS®P91 ROBOTIC CLEANER.
YOUR POLARIS P91 ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY
INSTALLED AND TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW
POLARIS P91 CLEANER, PLEASE DO THE FOLLOWING:
1) Complete and return the warranty card.
2) Record your purchase information on the spaces provided below.
3) Attach your invoice (or a copy) to this page.
Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please
contact your original dealer. If the original dealer does not perform warranty service, please visit
www.polarispool.com to locate an independent service company near you. If you are unable to locate a service
company, please call our Technical Support Department at 800-822-7933.
RECORD YOUR POLARIS P91 POOL CLEANER DATA HERE:
Date of Purchase Purchased From Serial Number:
(On ID Plate Located on Bottom of Control Unit)
City State Zip Code

Page 3
English
Table of Contents
Section 1. Important Safety Instructions........ 4
Section 2. Cleaner Specications................... 6
2.1 GeneralSpecications ....................................... 6
Section 3. Assembly and Initial Usage........... 6
3.1 Unpacking .......................................................... 6
3.3 Electrical Connection.......................................... 7
Section 4. Operation......................................... 7
4.1 Submerging the Cleaner .................................... 7
4.2 Operating the Cleaner ........................................ 7
4.3 Removing the Cleaner from Pool ....................... 8
Section 5. Cleaning and Maintenance ............ 9
5.1 Cleaning the Filter Canister................................ 9
5.2 Replacing the Filter Canister .............................. 9
5.4 Replacing the Brushes ..................................... 10
5.5 Replacing the Tires on the Cleaner ...................11
Section 6. Troubleshooting ........................... 12
Section 7. Polaris P91 Replacement Parts List
and Exploded View ...................... 13

Page 4
English
Section 1. Important Safety Instructions
Congratulations on purchasing the Polaris P91 Robotic Cleaner. Please take a moment to read through the entire
manual before installing your new robotic pool cleaner. Your cleaner must be installed and operated as specied.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
Failure to comply with the following warnings can result in permanent injury, electrocution or drowning.
PREVENT ELECTRICAL SHOCK
To reduce risk of electrical shock:
• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle should
be provided by a qualified installer and should be tested on a routine basis. To test the GFCI, push the test button.
The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in
this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed,
a ground current is flowing, indicating the possibility of an electric shock. Do not use this product. Disconnect the
cleaner and have the problem corrected by a qualified service representative before using.
• Per the United States National Electric Code (NEC®), keep the control unit at least five (5) feet from the edge of
the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC®) requires a minimum distance of 3m (10 ft.)
to be maintained between the pool edge and the control unit. Never submerge the control unit.
• Do not enter pool while the Polaris P91 is in water.
• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and other
equipment.
• To reduce the risk of electrical shock, do not use the Polaris P91 robotic cleaner or control unit if the cord is worn or
damaged. Contact Zodiac Pool Systems, Inc. Technical Support immediately for a replacement cord.
• Double insulation—For continued protection against possible electric shock, use only identical replacement parts
when servicing. Do not attempt repair of the Polaris P91 robotic cleaner, control unit, power cord, or floating cable.
• NEVER OPEN CONTROL UNIT.
• Do not use an extension cord to connect the unit to electric supply; provide a properly located outlet. The control
unit should be placed near the outlet box.
PREVENT CHILD INJURY AND DROWNING
• To reduce the risk of injury, do not permit children to operate this product.
• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of your
pool’s operational system.

Page 5
English
SAVE THESE INSTRUCTIONS
CAUTION
USE OF THE POLARIS P91 ROBOTIC CLEANER IN A VINYL LINER POOL
Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by
objects coming into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine
dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded
simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the installation
process or when it comes into contact with objects in the pool. Zodiac Pool Systems, Inc., is not responsible for,
and the Limited Warranty does not cover, pattern removal, abrasion or markings on vinyl liners.
CAUTION
Failure to comply with the following warnings could cause damage to pool equipment or
personal injury.
• The Polaris P91 must be installed and operated as specified.
• This product is intended for use with permanently-installed pools. Do not use with storable pools. A
permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily
disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for
storage and reassembled to its original integrity.
• Turn the Polaris P91 off before removing it from water, and do not operate out of water.
• Do not remove the cleaner from the pool for 15 minutes after the cleaning cycle has completed.
• Clean the filter canister in the Polaris P91 after each use.
• Donotusetheproductinyourpoolifthewatertemperatureisabove95˚F(35˚C)orbelow55˚F(13˚C).

Page 6
English
Section 2. Cleaner
Specications
2.1 General Specifications
The general specifications for the Polaris P91 are as
follows:
Control unit voltage: 100-240 VAC, 50/60 Hz
Polaris P91
supply voltage: 30 V DC, max.
Installed load: 70 W max
Cable length: 50 feet
15 m
Weight of cleaner: 12 lbs
5.75 kg
Filtration efciency: ne ltering
Cycle length: 2 hours approx
The Polaris P91 is a double-insulated product. A
double-insulated electrical appliance is one which has
been designed in such a way that it does not require
a safety connection to ground. The basic requirement
for double-insulation is that no single failure can result
in dangerous voltage becoming exposed so that it
might cause an electric shock and that this is achieved
without relying on an earthed (grounded) metal casing.
This is achieved by having two (2) layers of insulating
material surrounding live parts or by using reinforced
insulation.
Therefore, devices having double-insulated
construction, such as the Polaris P91, do not utilize a
grounded (three-prong) cord/plug.
Section 3. Assembly and Initial
Usage
3.1 Unpacking
The packaging should contain the following items
(Refer to Figure 1):
• Polaris P91 robotic cleaner
• Control unit
• Hardware and template
• Owner's Manual
Check that the unit has not been damaged during
transport. If you detect damage, contact Zodiac Pool
Systems, Inc. at 800.822.7933 before using your Polaris
P91 robotic cleaner.
Figure 1. Polaris P91 Components
Cleaner
Control Unit
Floating Cable
To unpack the Polaris P91 and its components:
1. Open the top aps of the carton.
2 Remove the control unit from the carton.
3. Remove the oating cable and then the cleaner
from the carton.
3.2 Attaching the Control Unit to a Wall
1. Place the template, provided with the unit, on
the wall where you want to attach the control
unit.
2. Using the 1/8" drill bit, drill three (3) holes.
Screw the three (3) 1/4" screws, provided with
the unit, into the holes and place the control
unit onto the screws. Refer to Figure 2.
Figure 2. Position Control Unit on the Wall

Page 7
English
3.3 Electrical Connection
WARNING
Failure to comply with the following warnings
can result in permanent injury, electric shock or
drowning.
PREVENT ELECTRICAL SHOCK
• Keep the control unit at least five (5) feet from the
edge of the pool (Canada 3m (10 ft.) per CEC®
requirements). Never submerge the control unit.
• Only connect the control unit to a receptacle
protected by a GFCI. Contact a certified electrician
if you cannot verify that the receptacle is protected
by a GFCI.
• Do not use an extension cord to connect the
control unit.
• Do not allow anyone to swim while the Polaris P91
robotic cleaner is in the pool.
For your safety and to obtain the best possible
performance from your Polaris P91, connect the
cleaner’s oating cable to the cleaner's control unit by
twisting the threaded connector until it is snug. Do not
overtighten. Refer to Figure 3.
Figure 3. Electrical Connection
Control Unit
Floating Cable
Threaded Connector
The green indicator light on the control unit will
illuminate for a short period to indicate that the cycle
is ready to start. Do not try to start a cycle until the
indicator is illuminated.
IMPORTANT
The Polaris P91 control unit is equipped with an
automatic shut off feature to prevent overheating if
operated in direct sunlight for an extended period of
time.
WARNING
The Polaris P91 control unit is water-resistant, not
waterproof. In order to prevent the risk of electric
shock which could result in serious injury or death,
never submerge the control unit.
Section 4. Operation
4.1 Submerging the Cleaner
1. While holding the cleaner by the handle,
submerge the cleaner in the pool and remove
any air trapped inside by keeping the unit
vertical. Make sure that the cleaner sinks to
the bottom of the pool. Refer to Figure 4.
Figure 4. Submerge the Cleaner Vertically
2. Spread the oating cable out over the pool,
ensuring there are no kinks or bends in the
cable. Refer to Figure 5.
Figure 5. Spread Floating Cable Over the Pool
4.2 Operating the Cleaner
1. To start your Polaris P91 robotic cleaner,
press the ON/OFF button. Refer to Figure 6.
The green indicator light illuminates and the
cleaner will start up after just a few seconds.

Page 8
English
NOTE The cleaner will clean the floor and lower portion of
the pool wall. The cleaner will not reach the water
line.
2. If you wish to stop the cleaner during the
cleaning cycle, press the ON/OFF and ensure
that the green LED light goes off. Refer to
Figure 6.
Figure 6. Start the Cleaner.
ON/OFF
Button
3. At the end of the cycle, the cleaner needs a
cool down period of 15 minutes to prevent
damage to the seals. During this period, the
green indicator is lit indicating the cleaner
should stay in the water.
4. After the cool down period is complete, the
green indicator will turn off. The unit can be
removed from the pool.
NOTE The Polaris P91 includes a safety feature that
automatically stops the cleaner if it is powered ON
when it is not submerged in the water. For pools
equipped with a beach area, this safety feature
allows the cleaner to reverse, and go back into the
pool.
4.3 Removing the Cleaner from Pool
1. After the cleaning cycle is completed and
the 15 minute cool down period has elapsed,
gently pull the oating cable toward the side of
the pool (see Figure 7).
CAUTION
To prevent damage to the cleaner, never lift the
cleaner out of the pool using the floating cable.
Always lift the cleaner using the handle.
2. Lift the cleaner out of the pool using the
handle. Drain the remaining water from the
cleaner by keeping it in a vertical position.
Refer to Figure 8.
Figure 7. Remove Cleaner From Pool
Figure 8. Keep Cleaner Vertical to Drain Water
3. Disconnect the control unit cable from the
electrical outlet.
4. Disconnect the cable from the control unit.
5. Coil the cable starting at the cleaner and
moving toward the connection point at control
unit. Remove any coils or twists along the
entire length of the cable.
6. Store cleaner out of direct sunlight.
IMPORTANT
• Use your Polaris P91 robotic cleaner as often as
needed to keep your pool clean.
• Clean the filter canister after each cleaning cycle.
• Do not leave your cleaner in the pool on a
permanent basis.
• At the end of each cycle, remove the cleaner from
the pool. Start at the cleaner head and untangle
any coils in the cable before storing the cleaner.

Page 9
English
Section 5. Cleaning and
Maintenance
WARNING
To avoid electric shock and other hazards which
could result in permanent injury or death, disconnect
(unplug) the cleaner from the electrical outlet before
performing any cleaning and maintenance.
5.1 Cleaning the Filter Canister
The lter canister should be cleaned at the end of each
cycle.
1. Ensure that the control unit cable has been
disconnected from the electrical outlet.
2. Set the unit on its wheels.
3. Push the cover latch and lift the cover. Refer to
Figure 9.
Figure 9. Open Cover of the Cleaner
4. Remove the lter assembly from the body, as
shown in Figure 10.
Figure 10. Remove the Filter Canister/Cover
Assembly
5. Press the canister clip with your nger to
separate the lter canister from the top cover,
as shown in Figure 11.
6. Wash the lter canister with clean water from
a hose.
Figure 11. Remove Filter Canister from Cover
5.2 Replacing the Filter Canister
1. Position the lter canister hooks on the top
cover receiving pins, as shown in Figure 12.
Top Cover
Receiving Pins
Top Cover
Figure 12. Engaging the Filter Canister Hooks on
Top Cover
2. Rotate the lter canister and lock it in place
using the front clip. Refer to Figure 13. When
the lter canister is installed properly on the
top cover, it will be rmly attached.
3. Locate the top cover hinges under the body
shoulders, as shown in Figure 14.

Page 10
English
4. Lower the cover and allow the cover latch to
lock the top cover in place (refer to Figure 9).
Figure 13. Position and Lock the Filter Canister
in Place
Front Clip
Figure 14. Replace the Cover
5.3 Cleaning and Storing the Cleaner
The cleaner must be cleaned regularly using slightly
soapy clean water, do not use solvents such as
trichloroethylene or its equivalents. Rinse the cleaner
generously using clean water. Do not let your cleaner
dry in direct sunlight near the pool.
NOTE The cleaner cable must be disconnected from the
control unit before removing the cleaner from the
pool.
5.4 Replacing the Brushes
The cleaner is tted with a PVC brush with a wear
indicator. To maintain cleaner performance at its best,
you will need to replace the brushes when the wear
indicator is reached.
1. Place the cleaner upside-down so that you can
access the brush. Refer to Figure 15.
2. Push on one of the arms of the brush to remove
its shaft from the bushing, as shown in Figure
15.
Figure 15. Push Brush Arm
3. Lift the brush and then remove it from the
cleaner. Refer to Figure 16.
4. Install the new brush shaft in its bushing. Refer
to Figure 16.
5. Install the second shaft (on the other side) of the
new brush in its bushing. Refer to Figure 16.
Figure 16. Remove and Replace the Brush From
the Cleaner
Brush
Shaft
Brush
Bushing

Page 11
English
5.5 Replacing the Tires on the Cleaner
1. Using your ngers, pull on the inside of the old
tire to remove the tire lip from the wheel. See
Figure 17.
2. Remove the old tire as shown in Figure 18.
Figure 17. Pull on Inside of Old Tire
Figure 18. Remove the Old Tire From the Cleaner
3. To replace the tire, position the new tire on the
wheel making sure to orient the tire so that the
tire groove pattern is on the outer side of the
wheel. See Figure 19.
Figure 19. Tire Replacement Orientation
4. Push one side of the tire on to the wheel and
t the tire onto the wheel as shown in Figure
20.
Figure 20. Push Tire onto the Wheel
5. Work the tire around and onto the wheel.
Refer to Figure 21.
Figure 21. Push the Tire Into Place

Page 12
English
Symptom Cause Solution
The cleaner does not move
and the green indicator light
does not illuminate.
Unit is OFF. Make sure the ON/OFF button is turned ON.
Cleaner is not supplied with
electricity.
1. The electrical outlet the control unit is connected
to is not supplying electrical power.
2. Plug main power cord into another electrical outlet
thatispoweredandensurethegreenlightashes
once.
3. If the green indicator does not illuminate, contact
your local Polaris service representative.
The green indicator light
ashesafteryoupressthe
ON/OFF button.
Control unit needs to be reset/not
properly connected.
Submerge the cleaner following the procedure in
Section 4.1, "Submerging the Cleaner".
1. To reset the supply:
a.Unplug the main power cord from the electrical
receptacle.
b.Disconnecttheoatingcableconnectorfrom
the control unit and then reconnect it following
the procedures in Section 3.3, "Electrical
Connection".
c. Plug the main cord in the electrical receptacle
and check if the green indicator light
illuminates.
d.Press the ON/OFF button. If the green indicator
doesnotilluminateorashes,contactyour
local Polaris service representative.
The cleaner does not pick
up the debris.
Thelterisfullordirty. Cleantheltercanisterfollowingtheprocedure
Section 5.1, "Cleaning the Filter Canister".
The cleaner does not stay
rmlyonthepoolbottom.
There is air in the appliance
casing.
Submerge the cleaner following the procedure
in Section 4.1, "Submerging the Cleaner". If the
problem persists, unscrew the cleaner over plate
andremovethepolystyreneoaterfrominsidethe
cover plate. Replace the cover and resubmerge the
cleaner.
The cleaner's ability to
climb the pool sides is
reduced.
NOTE: The cleaner is not
designed to climb up to the
waterline.
Thelterisfullordirty. Cleantheltercanisterfollowingtheprocedure
Section 5.1, "Cleaning the Filter Canister".
Tires are worn. Replace the tires following the procedure in Section
5.5, "Replacing the Tires on the Cleaner."
Sides of pool are slippery or
slimy. Although the water seems
clear, microscopic algae, invisible
to the human eye, are present
in the pool. As a result the pool
sides become slippery and
prevent the cleaner from climbing.
Ensure that your pool's chemicals are balanced.
If the chemicals are balanced, contact your local
Polaris service representative.
Section 6. Troubleshooting
WARNING
In order to prevent the risk of electric shock which could result in serious injury or death, DO NOT open the
control unit.

Page 13
English
Symptom Cause Solution
Right turning and/or rotating
isinefecient
There is debris under the pivot
stirrup.
Remove debris from the stirrup and verify that it
pivots freely.
The roller is worn. If the roller is worn, replace as necessary.
The cleaner is too light. Removethepolystyreneoater.Unscrewthecleaner
coverplateandremovethepolystyreneoater
from inside the cover plate. Replace the cover and
resubmerge the cleaner.
Leftturningisinefcient. The cleaner is too heavy. Contactyourresellertoobtainapolystyreneoater
to install under the cover plate.
Section 7. Replacement Parts
List and Exploded
View
The complete replacement parts list and exploded view
is available on the Polaris website at
www.polarispool.com.

Page 14
English
NOTES

Page 15
English

Zodiac Pool Systems, Inc.
2620 Commerce Way, Vista, CA 92081
1.800.822.7933 | www.ZodiacPoolSystems.com
ZODIAC®is a registered trademark of Zodiac International, S.A.S.U., used under license.
All trademarks referenced herein are the property of their respective owners.
©2011 Zodiac Pool Systems, Inc. H0351312 Rev A 1201
Conforms to UL 1081
Certied to CSA E63055-2-41

H0351312 Rev. A
MANUEL DU PROPRIÉTAIRE
AVERTISSEMENT
POUR VOTRE SÉCURITÉ – Pour toute procédure autre que l’entretien de routine et la maintenance
décrite dans ce manuel, ce produit doit être pris en charge par une entreprise autorisée et qualifiée pour
la réparation des équipements de piscine par les provinces ou territoires où ledit produit est installé
lorsque de telles exigences locales, provinciales ou territoriales sont édictées. Si aucune exigence locale,
provinciale ou territoriale n’est disponible, l’agent d’entretien doit être un professionnel avec suffisamment
d’expérience dans l’installation et la maintenance de l’équipement de piscine pour appliquer correctement
les consignes du présent manuel. L’installation ou l’utilisation inappropriée annulera la garantie.
P91

NOUS VOUS REMERCIONS D’ACHETER LE ROBOT NETTOYEUR POLARIS®P91.
VOTRE ROBOT POLARIS P91 A ÉTÉ CONÇU POUR ÊTRE INSTALLÉ FACILEMENT ET NE DEMANDER QU’UN
MINIMUM D’OPÉRATION D’ENTRETIEN. AVANT D’INSTALLER VOTRE NOUVEAU POLARIS P91, VEUILLEZ
SUIVRE LES ÉTAPES CI-DESSOUS :
1) Remplir et retourner le bon de garantie.
2) Enregistrer votre information d’achat dans les espaces prévus ci-dessous.
3) Joindre votre facture (ou une copie) à cette page.
Le respect de ces étapes assure un service rapide de garantie, le cas échéant. Si une réparation est requise,
veuillez communiquer avec votre détaillant d’origine. Si le détaillant d’origine ne remplit pas convenablement le
service de garantie, veuillez visiter www.polarispool.com pour localiser une société de services de réparation
indépendante près de chez vous. Si vous ne parvenez pas à localiser une société de services de réparation, veuillez
communiquer avec notre service du soutien technique au 1 800 822-7933.
ENREGISTREZ LES RÉFÉRENCES DE VOTRE ROBOT NETTOYEUR P91 ICI :
Date d’achat Acheté de Node série :
(Sur la plaque d’identification située au bas du module de commande)
Ville État/Province/Territoire Code postal

Page 19
Français
Table des matières
Section 1. Consignes de sécurité
importantes................................... 20
Section 2. Spécications du robot nettoyeur22
2.1 Spécicationsgénérales .................................. 22
Section 3. Assemblage et utilisation initiale 22
3.1 Désemballage ................................................. 22
3.3 Raccordement électrique ................................. 23
Section 4. Fonctionnement............................ 24
4.1 Immersion du robot nettoyeur ......................... 24
4.2 Fonctionnement du robot nettoyeur ................. 24
4.3 Retrait du nettoyeur de la piscine..................... 24
Section 5. Entretien et maintenance............. 25
5.1 Nettoyagedelacartoucheltrante................... 25
5.2 Remplacementdelacartoucheltrante........... 26
5.4 Remplacement des balais ................................ 27
5.5 Remplacement des pneus du
robot nettoyeur ................................................. 28
Section 6. Dépannage ................................... 29
Section 7. Vue éclatée et liste des pièces de
rechange du Polaris P91.............. 30

Page 20
Français
Section 1. Consignes de sécurité importantes
Félicitations, vous venez d’acheter un robot nettoyeur Polaris P91. Veuillez lire ce guide au complet avant d’installer
votre nouveau robot nettoyeur de piscine. Le robot nettoyeur doit être installé et utilisé selon ces directives.
LIRE ET SUIVRE TOUTES LES CONSIGNES
AVERTISSEMENT
Si les précautions suivantes ne sont pas observées, il y a risque de blessures graves, d’électrocution ou
de noyade.
ÉVITER LES CHOCS ÉLECTRIQUES
Pour réduire le risque d’un choc électrique :
• Brancher l’appareil à une prise protégée par un disjoncteur de fuite à la terre (DDFT). Un tel DDFT doit être fourni
par un installateur qualifié et doit faire l’objet de tests sur une base régulière. Pour tester le disjoncteur de fuite à la
terre, appuyer sur le bouton de test. Le disjoncteur de fuite à la terre doit couper l’alimentation électrique. Appuyer
sur le bouton de réinitialisation. L’alimentation électrique devrait être restaurée. Si le DDFT ne fonctionne pas de
cette façon, c’est qu’il est défectueux. Si le disjoncteur de fuite à la terre coupe l’alimentation de la pompe sans
que le bouton TEST ne soit enfoncé, un courant à la terre circule, indiquant la possibilité d’un choc électrique.
Ne pas utiliser ce produit. Débrancher le robot nettoyeur, puis faire corriger le problème par un technicien qualifié
avant son utilisation.
• Conformément au code électrique national des États-Unis (NEC®), garder le module de commande à une
distance de 1,5 m (5 pi) du bord de l’eau (piscine/spa). Au Canada, le Code canadien de l’électricité (CCE) exige
une distance minimale de 3 m (10 pi) entre le bord de la piscine et le module de commande. Ne jamais immerger
le module de commande.
• Ne pas entrer dans la piscine alors que le Polaris P91 est dans l’eau.
• Ne pas enterrer le cordon. Placer le cordon de manière à ce qu’il ne soit pas endommagé par une tondeuse à
gazon, un taille-haie et autre équipement.
• Pour réduire le risque de choc électrique, ne pas utiliser le Polaris P91 ou le module de commande si le cordon
est usé ou endommagé. Veuillez immédiatement communiquer avec Zodiac Pool Systems, Inc. pour un fil de
rechange.
• Isolation double : Pour une protection continue contre des chocs électriques possibles, n’utiliser que des pièces de
rechange identiques pour les réparations. Ne pas essayer de réparer le robot nettoyeur Polaris P91, le module de
commande, le cordon d’alimentation ou le câble flottant.
• NE JAMAIS OUVRIR LE MODULE DE COMMANDE.
• Ne pas utiliser une rallonge afin de brancher l’appareil à l’alimentation électrique; fournir une sortie localisée
adéquatement. Le module de commande doit être placé près de la boîte de sortie.
ÉVITER QUE LES ENFANTS SE BLESSENT OU SE NOIENT
• Pour réduire le risque de blessure, ne pas permettre aux enfants d’utiliser ou de faire fonctionner ce produit.
• Ne laisser personne, surtout de jeunes enfants, s’asseoir, mettre le pied, s’appuyer contre ou monter sur les
appareils faisant partie du système opérationnel de la piscine.