Polaris Maxx User manual

OWNER’S MANUAL
English |Français |Español
H0671300_REVB

English
2
WARNING
RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED CAN RESULT IN
SERIOUS INJURY OR DEATH. Ensure that your vacuum suction ttings installed in your pool for
connection of your suction-side pool cleaner are certied as being compliant with applicable safety
standards such as IAPMO SPS 4. Do not block the suction ttings with any part or your body. Do not
expose your hair, loose clothing, jewelry, etc. to any suction outlet ttings in the pool/spa.
To ensure prompt warranty service, should it be required, please:
• Complete and return the Polaris Warranty Card.
• Record your purchase information.
• Attach a copy of your purchase receipt to this document.
Date of Purchase: ___________ Purchased From: __________________________________
Serial Number (located under the hood) ___________________________________
If service is required, simply present your manual with the attached receipt at any Zodiac warranty center.
Notice for Vinyl Liner Pools: Before installing your pool cleaner, examine the interior of your pool carefully. If
the vinyl liner is brittle or has stones, wrinkles, roots or metal corrosion in contact with the underside of the liner, or has
damage to the base material or supporting walls, do not install the cleaner before having a qualified professional perform
the necessary repairs or liner replacement. Zodiac Pool Systems LLC. (Zodiac) and its affiliates and subsidiaries
will not be responsible for liner damage caused by a cleaner which is in disrepair, pattern removal from a vinyl
liner, or a cleaner used in a pool having an aged or deteriorated liner. Please see Limited Warranty.
• To help prevent suction entrapment accidents, wall vacuum fittings should have a safety vac lock
installed. Contact your builder or pool professional for details.
• Clean the skimmer basket, pump basket and pool filter before installing the cleaner on a regular
basis thereafter.
• Always disconnect the cleaner from the pool wall or skimmer before cleaning or backwashing the
pool filter. After cleaning or backwashing, let the filtration system run for at least five (5) minutes
before re-connecting the cleaner.
• Remove the cleaner from the pool before chemical or shock treatments. Wait a minimum of four (4)
hours after super chlorination before re-installing the cleaner.
Read owner’s manual completely before operating the cleaner.
Remove cleaner before entering the pool.
Do not operate outside of the pool.
Do not let children play with cleaner.
Keep hands clear from moving parts.
Important Information

English
3
Before You Start
Congratulations on the purchase of your new cleaner. Before installing your cleaner, please check the
box to ensure all parts are included (Figure 1). If any components are missing, contact:
Polaris Customer Support 1-800-822-7933 (USA)
1-888-647-4004 (Canada)
Always insist on genuine Polaris replacement parts. Non-Polaris parts are not made to our specifications
and may have an adverse effect on the operation of your cleaner, or may even damage it. Parts diagrams
and list of spare parts can be found at: www.polarispool.com
a - Cleaner Body
b - Flowkeeper™ Valve
c - Leader Hose Section with Hose Float
d - Twist-Lock 45 Degree Elbow, Extended
e - Flow Regulator Valve (FRV)
f - 45 Degree Elbow
g - Twist-Lock Hose Section
h - Valve Cuff
Included in the Box
Cleaner Components Shipped in the Box
a
g
e
x 11
f
d
b
h
c

English
4
Read the complete owner’s
manual before you begin installation.
Installation
STEP 1. Prepare the Pool
1. Manually vacuum the pool and make sure the pool filter and pump basket are clean.
2. Turn off the pool filter pump.
3. Close the pool main drain line.
4. Aim the return line fittings down.
WARNING
RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED CAN RESULT IN SERIOUS
INJURY OR DEATH. Ensure that your vacuum suction ttings installed in your pool for connection of
your suction-side pool cleaner are certied as being compliant with applicable safety standards such as
IAPMO SPS 4. Do not block the suction ttings with any part or your body. Do not expose your hair,
loose clothing, jewelry, etc. to any suction outlet ttings or hose ends in the pool/spa.
STEP 2. Assemble Hose Sections
Push and twist the connector on each hose section (g) until they lock into position with clicking sound
(Figure 1). Hose cuffs have three (3) connection positions. Any of the three (3) positions are sufficient
for an air-tight seal. g g
Figure 1. Hose Sections
Figure 2. Dedicated Suction
Line Connection
g
d
STEP 3. Connect to a Dedicated Suction Line
1. Twist-lock the male end of the hose (g) into the large end
of the extended 45° elbow (d).
2. Connect elbow to the installed Safety Vac
wall fitting (sold separately).
3. Angle the elbow toward the water surface (Figure 2).

English
5
OR
Connect to a Skimmer
The FlowKeeper™ valve must always be used in single skimmer installations. The valve regulates
flow to ensure the pool pump and cleaner run properly.
If the pool has more than one skimmer, connect the hose to the skimmer closest to the pump.
The parts used to connect the hose and the sequence in which they are installed depends on the type of
skimmer (Figure 3).
1. Remove the skimmer basket.
2. Connect the valve cuff (h), FlowKeeper valve (b) and the 45 degree elbow (f) together. Insert the
FlowKeeper valve (b) into the 45 degree elbow with arrow pointing down.
3. Push the male end of the twist-lock hose (g) to the end of the 45 degree elbow (f).
4. Insert assembly into the skimmer suction port.
Figure 3. Skimmer Connection
STEP 4. Determine Correct Hose Length for Your Pool
1. Measure enough hose to reach the farthest point of the pool from the skimmer or dedicated suction
line. Remove any additional hose sections, as necessary. See (A) in Figure 4, below.
2. Next attach the leader hose (c) to the end where the cleaner head will be connected. See (B) in
Figure 4 below. The extra length allows the cleaner to reach the far point in the pool if a loop forms
while in operation.
Leader Hose (B)
Skimmer or dedicated suction line
Farthest distance across pool (A)
g
c
Total Hose Length Required = (A) Farthest distance across pool + (B) Leader Hose
Figure 4. Determine Correct Hose Length
h
g
b
f
skimmer suction port

English
6
STEP 5. Connect the Cleaner
1. Ensure that the flow regulator valve (FRV) (e) is attached to the leader hose (c). The leader hose is
the hose section with the foam float pre-attached. (Figure 5).
2. Submerge the hose and flood with water (no bubbles visible).
3. Submerge the cleaner and flood with water (no bubbles visible).
4. Connect the hose to the cleaner head by pushing the flow regulator valve onto the cleaner.
5. Allow the cleaner to sink to the bottom of the pool.
Figure 5. Connect Hose and Submerge Cleaner
STEP 6. Test for Proper Flow
WARNING
To avoid serious injury, make sure to turn off the suction pump that is responsible for the pool cleaner
operation. Do not expose your hair, loose clothing, jewelry, etc. to the open end of the hose.
The flow regulator valve is designed to consistently limit high flow of water through the cleaner. When
flow is correct, the cleaner components are less susceptible to damage and the life of the cleaner can be
extended. Wheel rotation speed is a good indicator of how much water is flowing through the cleaner. By
checking for proper wheel rotation timing, you can verify the cleaner is operating at maximum efficiency.
c

English
7
Time Wheel Rotations
1. Turn on the pool filter pump.
2. Obtain a stopwatch or timer.
3. Leaving the pump on and water flowing through the
cleaner, bring the cleaner to the surface of the water
and hold it fully submerged just below the water line.
4. Locate the wheel speed indicator on the
rear right wheel (Figure 6).
5. Note how many seconds it takes to complete 10 rotations.
If the wheels change direction during the rotation count,
wait and restart your count.
If the count is within 20 - 25 seconds, no adjustment is
necessary.
• 20 - 25 seconds --- Optimal Flow
Figure 6. Wheel Speed Indicator
STEP 7. Adjust Flow to the Cleaner (If Necessary)
1. Adjust the flow if it is not within the optimal wheel speed range.
If the count is:
• 26 - 50 seconds --- Increase Flow (+) --- cleaner moving too slow and needs additional flow
• 10 - 19 seconds --- Decrease Flow (–) --- cleaner moving too fast and could be damaged
2. To increase or decrease flow, adjust flow via one of the following methods:
• Valves at the equipment pad for a dedicated suction line.
• Flowkeeper valve at the skimmer for skimmer installation (Figure 7).
• Pump speed (variable speed pumps only).
FlowKeeper
Adjustment
(+) Increase Flow
(–) Decrease Flow
Figure 7. Adjust FlowKeeper™ Valve

English
8
Operation and Maintenance
Daily Operation
The cleaner cycles on/off with the pool filtration pump, vacuuming and cleaning all surfaces randomly
throughout the pool. The climbing ability of the cleaner is dependent on the pool’s shape and available
water flow. If the cleaner is not climbing pool walls, ensure the flow is correct by checking the wheel
speed. Also, ensure the pool surface is not covered in algae as this slippery surface will affect traction.
During each coverage pattern cycle, the cleaner travels both forward and backwards, and pivots to the
right and left. The turbines underneath the cleaner create down force for climbing and stability as well as
directing debris into the cleaner mouth. The scrubbing brushes also make contact with the pool floor to
agitate and remove small stuck-on debris.
Cleaner Vacuum Modes
Your cleaner is designed to operate with two vacuum options:
• Large debris: For vacuuming large debris, such as leaves. It is recommended that you return the
cleaner to small debris factory setting after large debris cleaning.
• Small debris (factory setting): For vacuuming smaller and heavy debris, such as sand, silt and
small stones. The pool cleaner is sent from the factory in this mode.
WARNING
To avoid serious injury, make sure that the cleaner is disconnected from the hose and the suction
pump used for the cleaner is turned off prior to starting this operation.
Convert to large debris
cleaning mode:
1. Locate slot on underside of
cleaner. Insert a flat tool into
the inlet adapter
(Figure 8).
2. Lift up the inlet adapter and
then pull it out of the vacuum
inlet.
Convert back to small debris
cleaning mode:
1. Place the modular inlet adapter in the vacuum inlet
of the pool cleaner.
2. Push down on the modular inlet adapter until it
clicks into place (Figure 9).
Figure 8. Remove Modular Inlet Adapter Figure 9. Replace Modular Inlet Adapter

English
9
Routine Maintenance
To ensure correct operation and extend the life of your cleaner:
1. Empty the Pump Basket Regularly
For the cleaner to operate at highest efficiency, empty the pump basket regularly. The more debris in the
pool, the more often the pump basket should be cleared.
NOTE: Polaris offers an in-line leaf canister which maintains flow while catching debris, and reduces
debris from reaching the pump filter basket.
2. Remove Debris from Engine
WARNING
To avoid serious injury, make sure that the cleaner is disconnected from the hose and the suction
pump used for the cleaner is turned off prior to starting this operation.
Figure 10. Latch Release Button
Figure 11. Remove the Engine
Latch Release
Button
Latch Release
Button
1. Push the latch release button on the top of the cleaner
(Figure 10) to open the cover.
2. Open the lid and inspect the engine. Remove any debris.
3. If necessary, pull the engine by the engine blades and
remove it. No tools required (Figure 11).
4. Reinstall the engine. Make sure the engine is positioned
with the large wheel on the right side (marked A) when
reinstalling.
5. Close engine cover and ensure the latch clicks in place.

English
10
3. Clean or Backwash the Pool Filter
Always disconnect the cleaner from the pool wall before cleaning or backwashing the pool filter. After
cleaning or backwashing, let the filtration system run for at least five (5) minutes to flush out the suction
lines before re-connecting the cleaner.
4. Adding Chemicals
Remove the cleaner from the pool for at least four (4) hours when adding chemicals.
5. Replace Brushes Regularly
To maintain optimal cleaning, it is recommended to replace scrubbing brushes each season or when
significant wear is visible (Figure 12). To remove brushes, squeeze the plastic clip between two fingers
and pull out. Type of pool surface may also increase rate of wear to brushes.
NEW
brush
surface
WORN
brush
surface
6. Storage
Never store the cleaner in direct sunlight. Do not coil the hose.
Hose may develop a memory which can affect cleaner performance. Store the cleaner on its side or back
to avoid damage to turbine (all models) and brushes (Figure 13).
Figure 12. Inspect the Brushes
Figure 13. Store Cleaner on its Side
7. Winterizing
Before storing for winter, drain out all the water (freeze damage is not covered by the warranty). Remove
all connectors and adapters from the dedicated suction line or skimmer. Disassemble the hoses and lay
flat.

English
11
If you experience a problem with your Polaris cleaner, please follow the troubleshooting steps below to
restore performance. If further assistance is required, contact Polaris Technical Support at
[phone].
Troubleshooting
Problem Solution
Cleaner does not move or moves slowly. • Confirm that the main drain is closed.
• Check wheel speed to verify proper flow. Refer to section,
"Check for Proper Flow."
• Check to see if any interior teeth of the tracks are worn. If so,
contact your dealer for replacement tracks.
• Clean or backwash filter and empty pump basket.
• Check for debris caught in the engine. Refer to section,
“Remove Debris from Engine”.
• Switch cleaner to large debris cleaning mode. Refer to section,
“Cleaner Vacuum Modes”.
• Check for air in system. If water level in pump basket drops or
you see excessive air bubbles in the pump basket or coming
from the return lines, there is air in the system. Check hose
connections, tighten all fittings at pump and check o-ring at
pump basket for wear.
• For skimmer installations, check the Flowkeeper™ to make
sure that it can move freely with the water flow.
Cleaner pattern does not cover entire pool. • Confirm proper hose length for your pool. Refer to section,
“Determine Correct Hose Length."
• Count wheel rotations to verify proper flow. Refer to section,
“Check for Proper Flow”. Adjust flow if necessary.
• Ensure return line fittings are directed downward. Add a return
diverter if necessary.
• Make sure hose is not kinked or coiled. Lay in sun to straighten
if necessary.
• Verify hose float is positioned approximately 9" from cleaner
head on the leader hose (c/g).
• Observe cleaner for more than five (5) minutes and ensure that
each drive track is periodically reversing direction. If it is not,
contact dealer or service center for help.
Cleaner gets stuck at steps. • Observe cleaner for more than five (5) minutes and ensure that
each drive track is periodically reversing direction. If it is not,
contact you dealer or service center for help.
• Ensure the swivel on top of the cleaner rotates freely.
• Count wheel rotations to verify proper flow. Refer to section,
“Check for Proper Flow”. Adjust flow if necessary.
• Confirm proper hose length for your pool. Refer to section,
“Determine Correct Hose Length."
Cleaner won’t climb walls. • Count wheel rotations to verify proper flow. Refer to section,
“Check for Proper Flow”. Adjust flow if necessary.
• Verify hose float is positioned approximately 9" from cleaner
Cleaner riding on its side. • Verify hose float is positioned approximately 9" from cleaner.

Zodiac Pool Systems LLC
2882 Whiptail Loop # 100
Carlsbad, CA 92010
1.800.822.7933
polarispool.com
Zodiac Pool Systems Canada, Inc.
2-3365 Mainway, Burlington
ON L7M 1A6
1.800.822.7933
ZodiacPoolSystems.ca
H0671300_REVB
© 2021 Zodiac Pool Systems LLC. All rights reserved. Polaris® and the 3-wheeled
cleaner design are registered trademarks of Zodiac Pool Systems LLC. All other
trademarks referenced are the property of their respective owners.
© 2021 Zodiac Pool Systems LLC. Todos los derechos reservados. Polaris® y
el diseño de limpiafondos de tres ruedas son marcas registradas de Zodiac Pool
Systems LLC. Las demás marcas mencionadas en esta guía son propiedad de sus
respectivos propietarios.
© 2021 Zodiac Pool Systems LLC. Tous droits réservés.Polaris® et la conception
de nettoyeur à 3 roues sont des marques déposées de Zodiac Pool Systems
LLC. Toutes les autres marques de commerce citées dans le présent document
appartiennent à leurs propriétaires respectifs.