Polaroid Zip User manual

P0LMP01
User’s manual
Android
GK07X0000400

Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
CAUTION
1 Avoid contact with leaking or a damaged battery.
2 Do not short battery terminals.
3 Adult supervision is recommended when product is
used by young children.
4 Avoid areas of excessive heat or moisture.
5 Do not disassemble the battery.
This product contains electrical or electronic
materials. The presence of these materials
may. if not disposed of properly, have
potential adverse effects on the environment
and human health.
Presence of this label on the product means it should
not be disposed of as unsorted waste and must be
collected separately. As a consumer, you are responsible
for ensuring that this product is disposed of properly.
Risk of explosion if Battery is replaced by an incorrect type.
Dispose of used Batteries according to the instructions.
To charge this product, you must always use a DC 5V, 1A
or more. Certified/Listed Adapter which complies with LPS.
BATTERY WARNINGS
If the optimum operating temperature of (15~32°C) is not met
when using this device, it may not print or lead to failure to provide
the best print quality. (For stability of the product, refrain from
using it at a low temperature in the winter.)
Operating Temperature
Safety Precautions
2

Federal Communication Commission
Interference Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encour-
aged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment.

Radiation Exposure Statement:
The product comply with the FCC portable RF exposure
limit set forth for an uncontrolled environment and are
safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the
product can be kept as far as possible from the user body
or set the device to lower output power if such function is
available.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
4

Keep out of direct sunlight and
away from a heat source.
Do not place heavy objects
on the product.
Do not place containers of
liquid on the product.
Do not spray water directly
onto the product when cleaning.
Do not place the product
in very low temperatures.
Do not attempt
to disassemble, repair and
remodel it for yourself.
Do not drop or give it impact.
Comply with rated (5V1A) voltage
and current.
Do not place the product in a hot
or humid place.
Keep out of the reach
of children.
Keep away from magnetic
interference.
Do not place the
product in a place with humidity,
dust and soot.
Wipe it with a dry cloth when
cleaning.
A violation of labeling regulations can cause
serious injury or death.
WARNING
NOTICE
A violation of labeling regulations
causes minor injury or damage to the product.

1. Items confirmed before use
Installation in Store
3. Cover Open methodㅤ
Zink Smart Sheet
7
9
11
11
13
14
15
Table of Contents
Components
Names of parts
Power on/off
Charging the battery
2. Application installation
Installation with QR Code
4. Inserting printing paper
5. Description of LED Status Indicators
6. Product specifications
7. Items to check before reporting
a malfunction
8. Warranty Card 17
6

1. Items confirmed before use
Components
Printer USB cable for charging
Zink photo paper Manual
Names of parts

Power on/off
ON Press the power button
at least 3 seconds.
OFF Press the power button
for about 3 seconds.
Note
When you turn on the power, the operating status LED indicator
blinks for about 5 seconds. You can print it out when the blinking
ends, and the LED is turned on white.
Charging the battery
This device has a built-in battery.
Make sure that the battery
is charged fully before use.
Average charging time :
About 1 hour and 30 minutes.
Charging status indicator Description of status
Charging in progress
Charging completed
Use the standard charger provided by this device.
The use of a non-standard charger can cause malfunction
and exception from the subjects of warranty service.
Do not give abnormal impacts.
Notice
There may be the risk of electric shock during the process
of charging, so please use with care.
Checking charging status indicator
8

2. Application installation

Description of Settings Details
Function Description
Auto Exposure Automatic exposure settings
Print Mode Print mode settings
(Image Full, Paper Full)
Auto Power OFF
Auto power off setting
(None, 3 minutes, 5 minutes,
10 minutes)
Device Status Device status
(Idle, Busy, Paper Empty, etc.)
Battery Battery level
Number of
page Printed
The total number of pages
printed
MAC Address
Update Firmware and color correction
data updates
Bluetooth MAC address
10