Politec MANA DT SMA + DT3 User manual

Infrared barrier for
perimeter protection
range 250 m
SMA technology
and RS485 output.
Installation Manual.
1.1.1.1.1.1.1.1

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
2
INDEX
1
MAIN COMPONENT LIST
Pag. 4
2
ASSEMBLING THE CABLEPIT
Pag. 5
CABLE PIT POSITIONNING
Pag. 7
3
TRANSFORMER MOUNTING
Pag. 8
4
POWER SUPPLY CABLE (PS01B)
Pag. 10
5
CABLES AND WIRING
Pag. 12
6
CONNECTION TO POWER SUPPLY
Pag.13
CONNECTION TO BACK UP BATTERY
Pag. 14
7
SERIAL CONNECTION TO ADEBUS
Pag. 15
Connection to serial port for each column
Pag. 15
8
MICROWAVE
Pag. 16
TX MOTHER BOARD
Pag. 16
RX MOTHER BOARD
Pag. 17
Configuration dip switche
Pag. 18
CONNECTIONS AND DESCRIPTIONS CAVITY TX AND RX
Pag. 19
SENSITIVE ZONE
Pag. 19
DEAD ZONE
Pag. 20
START UP
Pag. 21
TX COLUMN
Pag. 21
RX COLUMN
Pag. 21
ALIGNMET
Pag. 22
WALK TEST
Pag. 22
SENSITIVITY
Pag. 23
DELAY
Pag. 23
INSTALLATION GUIDE
Pag. 24
sections
Pag. 24
Particular conditions
Pag. 25
MW TECHNICAL CHARACTERISTICS
Pag. 25

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
3
9
IR SECTION
Pag. 26
CABLES AND CONNECTION TO TERMINALS
Pag. 26
CONNECTION TO TERMINAL BLOCK (MES9C)
Pag. 26
CONNECTION AND SETTINGS HEATERS
Pag. 27
SYNCHRONIZATION
Pag. 28
Wired SYNC
Pag. 28
Optical SYNC
Pag. 30
OPTIC CONFIGURATION
Pag. 32
OPTICAL TX
Pag. 32
OPTICAL RX
Pag. 33
TX/RX SETTINGS 3 OPTICS
Pag. 34
10 TX/RX SETTINGS 2 OPTICS
Pag. 34
COLUMN ALIGNMENT
Pag. 35
CALIBRATION THROUGH SMA SYSTEM
Pag. 36
CALIBRATION WITH PARALLEL BEAMS
Pag. 38
CALIBRATION WITH CROSSED BEAMS
Pag. 39
SETTING AND PROGRAMMING MOTHERBOARD
Pag. 40
Led’s functionning
Pag. 41
CHARACTERISTICS AND DIP SWITCHES SET
Pag. 42
REACTION TIME ADJUSTMENT
Pag. 44
TECHNICAL SPECIFICATION IR
Pag. 45
10
DT3 SECTION
Pag. 45
DETECTION AREA
Pag. 45
PROGRAMMING & START UP
Pag. 46
FIXED FUNCTION ADJUSTMENT
Pag. 47
TECHNICAL CHARACTERISTICS DT3
Pag. 47
11
BARRIER TECHNICAL CHARACTERISTICS
Pag. 48
Installation recommendation
Verify that the beam tower is fully watertight once the cover and end caps have been correctly filled at the
end of the installation.
Use the cable glands supplied on the tower for all cabling must pass through the lower end cap using the
cable glands supplied. The missed used of proper accessories decrease the IP grade protection of the
tower.
Avoid any type of obstruction between the transmitter and receiver.
Avoid installing the receivers beams in a position where direct sunlight, at the same angle as the receivers
beams, can enter directly into optics especially at sunset and sunrise
Do not install multiple beams where the transmitter beam can interfere with other receiver beams. It is
always better place either transmitter or receivers back to back.

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
4
1.MAIN COMPONENT LIST
N°
DESCRIPTION
1
Top cap
2
IR cover
3
Aluminium profile
4
Aluminium base
5
Motherboard IR
6
Optics TX/RX
7
Motherboard MW
TX/RX
8
Parable TX/RX
9
Heather
10
Terminal block
11
Supply board
12Vcc/24 Vac
12
DT3
1
2
3
4
5
6
7
8
9
10
11
12

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
5
2. ASSEMBLING THE CABLEPIT
7.Insert the highlighted edge into other section and fix with screws
8.Insert the third section in the same way and fix with screws.

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
6
9.Enlarge the two opposite walls of cable pit to allow the positioning of last section.
10. Insert and well fix the missing screws.

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
7
2.1 CABLE PIT POSITIONING
The placement of the cable pit for MANA columns, after assembling, have to be done in the following way:
cement all around the cable pit keeping the top edge of it at same level of ground.
POSSIBLE CORRECTION OF THE INCORRECT
POSITIONING
Placement should be perpendicular to the ground. If the base is not in perfectly at ground level, is possible to
adjust it through the insert regulation of cable pit.
On the side that must be corrected loosen the insert in order to get the right inclination.
CORRECT POSITIONING
BY ADJUSTING INSERTS
EXAMPLE
OF SETTING
WRONG POSITIONING

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
8
3.TRANSFORMER MOUNTING
Kit compodes by:
1 transformer 160VA with 2 output;
1 screw 8x60;
2 nut M8;
1 perforated plate;
1 plate;
2 black sheath insulating;
4 anchor screw barrier.
Move the screw 60mm, as shown in the figure, in the perforated plate and screw the bolt lock.
Place the plate in the cavity, especially left, so you can screw tighten the screws to the column and have enough
space for the battery. Screw the 4 screws

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
9
Insert the sheath, the transformer then again the sheath and plate and fix everything with the nut. Follow the
wiring instruction in the manual.

Politec Srl | Manual MANA DT SMA + DT3 –Ver 2.5.2
10
POWER SUPPLY CABLE (PS01B)
N .
DECRIPTION
Power Connectors
(terminal 8)
1-2
19 Vac Input to be connected to the transformer
3-4
13.8 Vdc Output for power infrared
5-6
24 Vac Input to be connected to the transformer
7-8
24 Vac Output to be connected to the heaters
12345678
1
2
3
4
5
6
1 2 3 4 5 6
7