Polk Audio DXi 124 SVC User manual

ENGLISH
SAFE LIMITS OF OPERATION
Polk Audio specifies the recommended amplification range
for each of its passive (non-amplified) loudspeakers. Typically
that specification will be expressed as a range of power such
as 20-200 W (per channell. It is important to understand
what those numbers mean when choosing a receiver or
amplifier for your Polk loudspeakers. The lower number
indicates the lowest continuous rated power that will yield
acceptable performance in a typical listening environment.
The higher number indicates the highest per channel power
that should be used with your Polk speakers That number
should not be confused with a "Power Handling" specification
and it does not imply that the speaker will safely handle
that full amount of power on a long-term basis. We specify
a wide range of power ratings because not all electronics
manufacturers use the same method for rating power.
In fact, high quality lower-rated amplifiers sound better and
play louder than low quality units with a higher power rating.
Automobile horsepower is a good analogy. Your car probably
has far more horsepower than it needs for your daily commute
and is likely capable of going well over 120mph (190km/hr)
Having that extra power is good for on-ramp acceleration
BRING ON THE NOIZE!
Please inspect each loudspeaker carefully. Notify your
Polk Audio dealer if you notice any damage or missing items.
Keep the carton and packing material. They will do the best
job of protecting your speakers if they need to be transported.
BUILDING A HOME FOR YOUR SUBWOOFER-
DXi SUB ENCLOSURE 101
To get the best performance from your DXi Subwoofers,
you must use a Subwoofer Enclosure. Don't bother
using them in "free air," with no sub box, just popped into
the back deck of your car. You will not get very good
performance from your subwoofers if you do this.
They are not designed to be installed infinite baffle or
"free air." This will void the warranty.
You can build your own box, buy a pre-built box or a box kit,
or have your Polk Audio dealer design and build a custom sub
enclosure for you. Your DXi Subwoofers were designed to work
well in a wide variety of enclosure sizes and configurations.
If you choose to build your own enclosure, be sure to build
it well. Make certain it's properly sealed and airtight for
maximum bass performance.
and danger avoidance (like getting away from brain-eating
zombies) but that doesn't mean that it is advisable to operate
your car on North American highways at full power and
maximum speed for an extended period of time. Just ask
your local state trooper if you are in doubt. Similarly, we
recommend using amplifiers and receivers with rated power
above the Power Handling limits of our speakers because
having extra power available for short term peaks is conducive
to better sound quality, maximum dynamic range and effortless
high volume output. But we strongly urge you not to use the
full power of your amplifier or receiver for daily listening.
Loudspeakers can be damaged when an amplifier, regardless
of its wattage, is made to play at higher listening levels than its
power can clearly produce Operation at this level can result in
very high levels of audible distortion originating in the
amplifier, which can add a harsh, gritty sound to your listening
material. If you hear distortion-turn the volume down
or risk damaging your speakers. You can damage just
about any speaker, regardless of power rating, if you drive an
amplifier to or beyond the point of distortion.
Polk Audio Customer Service is available from
9a~pm, EST, Monday through Friday, at 800-377-7655
(US & Can only, outside the US please call
410-358-36(0) or email [email protected]
Please do not hesitate to call us if you have questions
about your speaker system. We love this stuff.
RECOMMENDED SEALED ENCLOSURES
DXi104 svc & 104 ovc 0.66 cu ft (18.7L)
DXi124 svc & 124 ovc 0.88 cu ft (24.9LI
For more information about enclosures and configurations, log
on to www.polkaudio.com/car/toolbox/subboxplansl Or call
Polk Audio's Customer Service Department for a FAXback Sub
Enclosure info sheet.
2 DXi High Performance Car Speakers
ENGLISH
SAFE LIMITS OF OPERATION
Polk Audio specifies the recommended amplification range
for each of its passive (non-amplified) loudspeakers. Typically
that specification will be expressed as a range of power such
as 20-200 W (per channell. It is important to understand
what those numbers mean when choosing a receiver or
amplifier for your Polk loudspeakers. The lower number
indicates the lowest continuous rated power that will yield
acceptable performance in a typical listening environment.
The higher number indicates the highest per channel power
that should be used with your Polk speakers That number
should not be confused with a "Power Handling" specification
and it does not imply that the speaker will safely handle
that full amount of power on a long-term basis. We specify
a wide range of power ratings because not all electronics
manufacturers use the same method for rating power.
In fact, high quality lower-rated amplifiers sound better and
play louder than low quality units with a higher power rating.
Automobile horsepower is a good analogy. Your car probably
has far more horsepower than it needs for your daily commute
and is likely capable of going well over 120mph (190km/hr)
Having that extra power is good for on-ramp acceleration
BRING ON THE NOIZE!
Please inspect each loudspeaker carefully. Notify your
Polk Audio dealer if you notice any damage or missing items.
Keep the carton and packing material. They will do the best
job of protecting your speakers if they need to be transported.
BUILDING A HOME FOR YOUR SUBWOOFER-
DXi SUB ENCLOSURE 101
To get the best performance from your DXi Subwoofers,
you must use a Subwoofer Enclosure. Don't bother
using them in "free air," with no sub box, just popped into
the back deck of your car. You will not get very good
performance from your subwoofers if you do this.
They are not designed to be installed infinite baffle or
"free air." This will void the warranty.
You can build your own box, buy a pre-built box or a box kit,
or have your Polk Audio dealer design and build a custom sub
enclosure for you. Your DXi Subwoofers were designed to work
well in a wide variety of enclosure sizes and configurations.
If you choose to build your own enclosure, be sure to build
it well. Make certain it's properly sealed and airtight for
maximum bass performance.
and danger avoidance (like getting away from brain-eating
zombies) but that doesn't mean that it is advisable to operate
your car on North American highways at full power and
maximum speed for an extended period of time. Just ask
your local state trooper if you are in doubt. Similarly, we
recommend using amplifiers and receivers with rated power
above the Power Handling limits of our speakers because
having extra power available for short term peaks is conducive
to better sound quality, maximum dynamic range and effortless
high volume output. But we strongly urge you not to use the
full power of your amplifier or receiver for daily listening.
Loudspeakers can be damaged when an amplifier, regardless
of its wattage, is made to play at higher listening levels than its
power can clearly produce Operation at this level can result in
very high levels of audible distortion originating in the
amplifier, which can add a harsh, gritty sound to your listening
material. If you hear distortion-turn the volume down
or risk damaging your speakers. You can damage just
about any speaker, regardless of power rating, if you drive an
amplifier to or beyond the point of distortion.
Polk Audio Customer Service is available from
9a~pm, EST, Monday through Friday, at 800-377-7655
(US & Can only, outside the US please call
410-358-36(0) or email [email protected]
Please do not hesitate to call us if you have questions
about your speaker system. We love this stuff.
RECOMMENDED SEALED ENCLOSURES
DXi104 svc & 104 ovc 0.66 cu ft (18.7L)
DXi124 svc & 124 ovc 0.88 cu ft (24.9LI
For more information about enclosures and configurations, log
on to www.polkaudio.com/car/toolbox/subboxplansl Or call
Polk Audio's Customer Service Department for a FAXback Sub
Enclosure info sheet.
2 DXi High Performance Car Speakers

WIRING DIAGRAMS FOR DXi104 svc, DXi124 svc
Please make certain that your amplifier is rated to carry the specified load.
SCHEMA DE CABLAGE DXi104 svc, DXi124 svc
Assurez-vous que votre amplificateur peut soutenir les charges specifiees.
DlAGRAMAS DE CABLEADO PARA LOS MODELOS DXi104 svc Y DXi124 svc
Asegurese de que el amplificador tenga la clasificaci6n nominal necesaria para Ilevar la carga especificada.
SCHALTPLANE FUR DXi104 svc. DXi124 svc
Vergewissern Sie sich, dass Ihr Verstarker die angegebenen Werte erfOllt
CABLAGGIO PER I MODELLI DXi104 svc. DXi124 svc
Accertarsi che i valori nomina Ii dell'amplificatore siano adeguati al carico specificato.
ESQUEMAS DE L1GACAO PARA AS UNIDADES DXi104 svc. DXi124 svc
o amplificador deve ter capacidade para suportar a carga especificada.
EJ
(±J===::i(±J
AMP
8--~
Single 4 Ohm load.
Charge simple 4 Ohms.
Carga (mica de 4 Ohms.
Einzeln: 4-0hm-Lastvviderstand.
Carico da 4 Ohm singolo.
Carga simples de 4 Ohm.
With speakers wired in parallel: Two 4 Ohm
speakers will present a2 Ohm load.
Deux haut-parleurs de 4 Ohm connectes en
parallele constituent une charge de 2 Ohm.
Con los altavoces en paralelo: Dos altavoces
de 4 Ohm presentan una carga de 2 Ohm.
Parallel geschaltete Lautsprecher: Zwei 4-0hm-
Lautsprecher fijhren zu einem 2-0hm-Lastvviderstand.
Con idiffusori collegati in parallelo: due diffusori
da 4 Ohm presentano un carico di 2 Ohm.
Com as bobinas em paralelo, um alto-falante
de 4 Ohm tera uma carga de 2 Ohm.
8 DXi: High Performance Car Speakers
WIRING DIAGRAMS FOR DXi104 svc, DXi124 svc
Please make certain that your amplifier is rated to carry the specified load.
SCHEMA DE CABLAGE DXi104 svc, DXi124 svc
Assurez-vous que votre amplificateur peut soutenir les charges specifiees.
DlAGRAMAS DE CABLEADO PARA LOS MODELOS DXi104 svc Y DXi124 svc
Asegurese de que el amplificador tenga la clasificaci6n nominal necesaria para Ilevar la carga especificada.
SCHALTPLANE FUR DXi104 svc. DXi124 svc
Vergewissern Sie sich, dass Ihr Verstarker die angegebenen Werte erfOllt
CABLAGGIO PER I MODELLI DXi104 svc. DXi124 svc
Accertarsi che i valori nomina Ii dell'amplificatore siano adeguati al carico specificato.
ESQUEMAS DE L1GACAO PARA AS UNIDADES DXi104 svc. DXi124 svc
o amplificador deve ter capacidade para suportar a carga especificada.
EJ
(±J===::i(±J
AMP
8--~
Single 4 Ohm load.
Charge simple 4 Ohms.
Carga (mica de 4 Ohms.
Einzeln: 4-0hm-Lastvviderstand.
Carico da 4 Ohm singolo.
Carga simples de 4 Ohm.
With speakers wired in parallel: Two 4 Ohm
speakers will present a2 Ohm load.
Deux haut-parleurs de 4 Ohm connectes en
parallele constituent une charge de 2 Ohm.
Con los altavoces en paralelo: Dos altavoces
de 4 Ohm presentan una carga de 2 Ohm.
Parallel geschaltete Lautsprecher: Zwei 4-0hm-
Lautsprecher fijhren zu einem 2-0hm-Lastvviderstand.
Con idiffusori collegati in parallelo: due diffusori
da 4 Ohm presentano un carico di 2 Ohm.
Com as bobinas em paralelo, um alto-falante
de 4 Ohm tera uma carga de 2 Ohm.
8 DXi: High Performance Car Speakers

DUAL VOICE COIL WIRING DIAGRAMS FOR DXi104 Dye & DXi124 Dye
Please make certain that your amplifier is rated to carry the specified load.
SCHEMA DE CABLAGE-BOBINES ACOUSTIOUES JUMELEES: DXi104 Dye, & DXi124 Dye
Assurez-vous que votre amplificateur peut soutenir les charges specifiees.
D1AGRAMAS DE CABLEADO PARA LOS MODELOS DXi104 Dye Y DXi124 Dye CON DOS BOBINAS DE VOZ
Asegurese de que el amplificador tenga la c1asificaci6n nominal necesaria para lIevar la carga especificada.
SCHALTPLANE IDOPPEL-SCHWINGSPULE) FUR DXi104 Dye & DXi124 Dye
Vergewissern Sie sich, dass Ihr Verstarker die angegebenen Werte erfOIit.
CABLAGGIO A BOBINA MOBILE DOPPIA PER I MODELLI DXi104 Dye E DXi124 Dye
Accertarsi che i valori nominali dell'amplificatore siano adeguati al carico specificato.
ESOUEMAS DE L1GACAO PARA AS UNIDADES DXi104 Dye E DXi124 Dye (bobina movel dupla)
o amplificador deve ter capacidade para suportar a carga especificada.
__ 1
E]
(f)=!. 1
AMP
8r .J'J
With coils in parallel, adual4 Ohm speaker
will present a2 Ohm load.
Un haut-parleur a bobines 4 Ohm jumeh~es
eonfigurees en paralh:Jle constitue une charge
de 2 Ohm,
With coils wired in series, adual4 Ohm speaker
will present an 8 Ohm load.
Un haut-parleur a bobines 4 Ohm jumelees
configurees en serie constitue une charge
de 8 Ohm.
Con las bobinas en paralelo, un altavoz de dos
bobinas de 4 Ohm presenta una carga de 2 Ohm.
Bei parallel geschalteten Schwingspulen fUhrt
ein doppelter 4-0hm-Lautsprecher zu einem
2-0hm-Lastwiderstand.
Con Ie bobine in parallelo, un diffusore
da 4 Ohm doppio presenta un carico di 2 Ohm.
Com as bobinas em paralelo, urn alto-falante
de 4 Ohm tera uma carga de 2 Ohm.
Con las bobinas en serie, un altavol de dos
bobinas de 4 Ohm presenta una carga de 8 Ohm.
Bei in Reihe geschalteten Schwingspulen fUhrt
ein doppelter 4-0hm-Lautsprecher zu einem
8-0hm-Lastwiderstand.
Con Ie bobine in serie, un diffusore da 4 Ohm
doppio presenta un carico di 8 Ohm.
Com as bobinas ligadas em serie, urn alto-
falante de 4 Ohm tera uma carga de 8 Ohm.
More Info @ www.polkaudio.com/ear 9
DUAL VOICE COIL WIRING DIAGRAMS FOR DXi104 Dye & DXi124 Dye
Please make certain that your amplifier is rated to carry the specified load.
SCHEMA DE CABLAGE-BOBINES ACOUSTIOUES JUMELEES: DXi104 Dye, & DXi124 Dye
Assurez-vous que votre amplificateur peut soutenir les charges specifiees.
D1AGRAMAS DE CABLEADO PARA LOS MODELOS DXi104 Dye Y DXi124 Dye CON DOS BOBINAS DE VOZ
Asegurese de que el amplificador tenga la c1asificaci6n nominal necesaria para lIevar la carga especificada.
SCHALTPLANE IDOPPEL-SCHWINGSPULE) FUR DXi104 Dye & DXi124 Dye
Vergewissern Sie sich, dass Ihr Verstarker die angegebenen Werte erfOIit.
CABLAGGIO A BOBINA MOBILE DOPPIA PER I MODELLI DXi104 Dye E DXi124 Dye
Accertarsi che i valori nominali dell'amplificatore siano adeguati al carico specificato.
ESOUEMAS DE L1GACAO PARA AS UNIDADES DXi104 Dye E DXi124 Dye (bobina movel dupla)
o amplificador deve ter capacidade para suportar a carga especificada.
__ 1
E]
(f)=!. 1
AMP
8r .J'J
With coils in parallel, adual4 Ohm speaker
will present a2 Ohm load.
Un haut-parleur a bobines 4 Ohm jumeh~es
eonfigurees en paralh:Jle constitue une charge
de 2 Ohm,
With coils wired in series, adual4 Ohm speaker
will present an 8 Ohm load.
Un haut-parleur a bobines 4 Ohm jumelees
configurees en serie constitue une charge
de 8 Ohm.
Con las bobinas en paralelo, un altavoz de dos
bobinas de 4 Ohm presenta una carga de 2 Ohm.
Bei parallel geschalteten Schwingspulen fUhrt
ein doppelter 4-0hm-Lautsprecher zu einem
2-0hm-Lastwiderstand.
Con Ie bobine in parallelo, un diffusore
da 4 Ohm doppio presenta un carico di 2 Ohm.
Com as bobinas em paralelo, urn alto-falante
de 4 Ohm tera uma carga de 2 Ohm.
Con las bobinas en serie, un altavol de dos
bobinas de 4 Ohm presenta una carga de 8 Ohm.
Bei in Reihe geschalteten Schwingspulen fUhrt
ein doppelter 4-0hm-Lautsprecher zu einem
8-0hm-Lastwiderstand.
Con Ie bobine in serie, un diffusore da 4 Ohm
doppio presenta un carico di 8 Ohm.
Com as bobinas ligadas em serie, urn alto-
falante de 4 Ohm tera uma carga de 8 Ohm.
More Info @ www.polkaudio.com/ear 9

DUAL
VOICE
COIL
WIRING
DIAGRAMS
FOR
DXi104
DVC
&
DXi124
DVC
SCHEMA
DE
CABLAGE-BOBINES
ACOUSTIOUES
JUMElEES:
DXi104
DVC
ET
DXi124
DVC
DlAGRAMAS
DE
CABLEADO
PARA
LOS
MODElOS
DXi104
DVC
Y
DXi124
DVC
CON
DOS
BOBINAS
DE
VOl
SCHALTPLANE
(DOPPEL-SCHWINGSPULE)
FUR
DXi104
DVC
&
DXi124
DVC
CABLAGGIO
A
BOBINA
MOBILE
DOPPIA
PER
I
MODELLI
DXi104
DVC
E
DXi124
DVC
ESOUEMAS
DE
lIGACAO
PARA
AS
UNIDADES
DXi104
DVC
E
DXi124
DVC
(BOBINA
MOVEl
DUPLA)
8
:>-+1-
.......
-----.
With
coils
and
speakers
wired
in
parallel,
two
dual
4
Ohm
speakers
will
present
a1
Ohm
load.
(Not
recommended
unless
amplifier
is
rated
for
1
Ohm
operation.)
Deux
haut-parleurs,
a
bobines
4
Ohm
jumeh~es
configurees
en
parallele,
cables
en
parallele
constituent
une
charge
de
1
Ohm.
(Non
recommande
a
moins
que
I'amplificate
ur
soit
capable
de
soutenir
une
charge
de
1
Ohm.)
Con
las
bobinas
y
los
altavoces
en
paralelo,
2
altavoces
de
dos
bobinas
y
4
Ohm
presentan
una
carga
de
1
Ohm.
(Se
recomienda
no
utilizar
este
cableado
a
menos
que
el
amplificador
tenga
una
clasificaci6n
nominal
para
funcionar
con
1
Ohm.)
Bei
parallel
geschalteten
Schwingspulen
und
Lautsprechern
fOhren
2
doppelte
4-0hm-Lautsprecher
zu
einem
1-0hm-Lastwiderstand.
(Nur
zu
empfehlen,
wenn
der
Verstarker
fOr
den
1-0hm-Betrieb
ausgelegt
ist.)
Con
Ie
bobine
ei
diffusori
collegati
in
parallelo:
due
diffusori
da
4
Ohm
doppi
presentano
un
carico
di
1
Ohm.
(Configurazione
sconsigliata
a
menD
che
i
valori
nominali
dell'amplificatore
non
siano
adeguati
al
funzionamento
a1
Ohm.)
Com
as
bobinas
e
os
alto-falantes
ligados
em
paralelo,
dois
alto-falantes
duplos
de
4
Ohm
terao
uma
carga
de
1
Ohm.
(Nao
recomendado
a
nao
ser
que
0amplificador
seja
classificado
para
funcionamento
em
1
Ohm.)
With
the
coils
wired
in
series
and
the
speakers
wired
in
parallel,
2dual4
Ohm
speakers
will
present
a4
Ohm
load.
Deux
haut-parleurs,
a
bobines
4
Ohm
jumelees
configurees
en
serie,
cables
en
parallele
constituent
une
charge
de
4
Ohm.
Con
los
las
bobinas
en
serie
y
los
altavoces
en
paralelo,
2
altavoces
de
dos
bobinas
de
4
Ohm
presentan
una
carga
de
4
Ohm.
Bei
in
Reihe
geschalteten
Schwingspulen
und
parallel
geschalteten
Lautsprechern
fOhren
2
doppelte
4-0hm
Lautsprecher
zu
einem
4-0hm-Lastwiderstand.
Con
Ie
bobine
in
serie
ei diffusori
in
parallelo,
due
diffusori
da
4
Ohm
doppi
presentano
un
carico
di
4
Ohm.
Com
as
bobinas
ligadas
em
serie
e
os
alto-falantes
ligados
em
paralelo,
dois
alto-falantes
duplos
de
4
Ohm
terao
uma
carga
de
4
Ohm.
10
DXi:
High
Performance
Car
Speakers
DUAL
VOICE
COIL
WIRING
DIAGRAMS
FOR
DXi104
DVC
&
DXi124
DVC
SCHEMA
DE
CABLAGE-BOBINES
ACOUSTIOUES
JUMElEES:
DXi104
DVC
ET
DXi124
DVC
DlAGRAMAS
DE
CABLEADO
PARA
LOS
MODElOS
DXi104
DVC
Y
DXi124
DVC
CON
DOS
BOBINAS
DE
VOl
SCHALTPLANE
(DOPPEL-SCHWINGSPULE)
FUR
DXi104
DVC
&
DXi124
DVC
CABLAGGIO
A
BOBINA
MOBILE
DOPPIA
PER
I
MODELLI
DXi104
DVC
E
DXi124
DVC
ESOUEMAS
DE
lIGACAO
PARA
AS
UNIDADES
DXi104
DVC
E
DXi124
DVC
(BOBINA
MOVEl
DUPLA)
8
:>-+1-
.......
-----.
With
coils
and
speakers
wired
in
parallel,
two
dual
4
Ohm
speakers
will
present
a1
Ohm
load.
(Not
recommended
unless
amplifier
is
rated
for
1
Ohm
operation.)
Deux
haut-parleurs,
a
bobines
4
Ohm
jumeh~es
configurees
en
parallele,
cables
en
parallele
constituent
une
charge
de
1
Ohm.
(Non
recommande
a
moins
que
I'amplificate
ur
soit
capable
de
soutenir
une
charge
de
1
Ohm.)
Con
las
bobinas
y
los
altavoces
en
paralelo,
2
altavoces
de
dos
bobinas
y
4
Ohm
presentan
una
carga
de
1
Ohm.
(Se
recomienda
no
utilizar
este
cableado
a
menos
que
el
amplificador
tenga
una
clasificaci6n
nominal
para
funcionar
con
1
Ohm.)
Bei
parallel
geschalteten
Schwingspulen
und
Lautsprechern
fOhren
2
doppelte
4-0hm-Lautsprecher
zu
einem
1-0hm-Lastwiderstand.
(Nur
zu
empfehlen,
wenn
der
Verstarker
fOr
den
1-0hm-Betrieb
ausgelegt
ist.)
Con
Ie
bobine
ei
diffusori
collegati
in
parallelo:
due
diffusori
da
4
Ohm
doppi
presentano
un
carico
di
1
Ohm.
(Configurazione
sconsigliata
a
menD
che
i
valori
nominali
dell'amplificatore
non
siano
adeguati
al
funzionamento
a1
Ohm.)
Com
as
bobinas
e
os
alto-falantes
ligados
em
paralelo,
dois
alto-falantes
duplos
de
4
Ohm
terao
uma
carga
de
1
Ohm.
(Nao
recomendado
a
nao
ser
que
0amplificador
seja
classificado
para
funcionamento
em
1
Ohm.)
With
the
coils
wired
in
series
and
the
speakers
wired
in
parallel,
2dual4
Ohm
speakers
will
present
a4
Ohm
load.
Deux
haut-parleurs,
a
bobines
4
Ohm
jumelees
configurees
en
serie,
cables
en
parallele
constituent
une
charge
de
4
Ohm.
Con
los
las
bobinas
en
serie
y
los
altavoces
en
paralelo,
2
altavoces
de
dos
bobinas
de
4
Ohm
presentan
una
carga
de
4
Ohm.
Bei
in
Reihe
geschalteten
Schwingspulen
und
parallel
geschalteten
Lautsprechern
fOhren
2
doppelte
4-0hm
Lautsprecher
zu
einem
4-0hm-Lastwiderstand.
Con
Ie
bobine
in
serie
ei diffusori
in
parallelo,
due
diffusori
da
4
Ohm
doppi
presentano
un
carico
di
4
Ohm.
Com
as
bobinas
ligadas
em
serie
e
os
alto-falantes
ligados
em
paralelo,
dois
alto-falantes
duplos
de
4
Ohm
terao
uma
carga
de
4
Ohm.
10
DXi:
High
Performance
Car
Speakers

With the coils wired in series and the speakers
wired in parallel, 3dual4 Ohm speakers will present
a 2.7 Ohm load.
Trois haut-parleurs, a bobines 4 Ohm jumelees
configurees en serie, cables en parallele constituent
une charge de 2,7 Ohm.
Con las bobinas en serie y los altavoces en paralelo,
3 altavoces de 4 Ohm presentan una carga de 2.7 Ohm.
Bei in Reihe geschalteten Schwingspulen und parallel
geschalteten Lautsprechern fUhren 3 doppelte 4-0hm
Lautsprecher zu einem 2,7-0hm-Lastwiderstand.
Con Ie bobine in serie ei diffusori in parallelo,
tre diffusori da 4 Ohm doppi presentano un
carico di 2,7 Ohm.
Com as bobinas ligadas em serie e os alto-falantes
ligados em paralelo, tres alto-falantes duplos de
4 Ohm terao uma carga de 2,7 Ohm.
More Info @ www.polkaudio.com/car 11
With the coils wired in series and the speakers
wired in parallel, 3dual4 Ohm speakers will present
a 2.7 Ohm load.
Trois haut-parleurs, a bobines 4 Ohm jumelees
configurees en serie, cables en parallele constituent
une charge de 2,7 Ohm.
Con las bobinas en serie y los altavoces en paralelo,
3 altavoces de 4 Ohm presentan una carga de 2.7 Ohm.
Bei in Reihe geschalteten Schwingspulen und parallel
geschalteten Lautsprechern fUhren 3 doppelte 4-0hm
Lautsprecher zu einem 2,7-0hm-Lastwiderstand.
Con Ie bobine in serie ei diffusori in parallelo,
tre diffusori da 4 Ohm doppi presentano un
carico di 2,7 Ohm.
Com as bobinas ligadas em serie e os alto-falantes
ligados em paralelo, tres alto-falantes duplos de
4 Ohm terao uma carga de 2,7 Ohm.
More Info @ www.polkaudio.com/car 11

ENGLISH
AMPLIFIER HOOKUP
o
o
NOTE: USE WITH 2 OHM COMPATIBLE AMPLIFIERS.
NOT ALL AMPLIFIERS ARE STABLE INTO A2 OHM LOAD
(ESPECIALLY IN BRIDGED MODE). PLEASE CONSULT
YOUR AMPLIFIER'S OWNER'S MANUAL.
SPECIFICATIONS
DXi112
Type
Frequency Response
Driver Complement
Nominal Impedance
Power Handling (RMS)
Recommended Amplification Range
Power Handling (Peak)
Efficiency
Dimensions
subwoofer enclosure/slot ported
26 Hz - 200 Hz
1- 12" diameter
2 Ohm
360 Watts
50 - 500 Watts
720 Watts
100 dB
Bottom Depth -1811/16" (474.3mm)
Top Depth - 1511/16" (398.1 mm)
Height - 143/4" (374.7mm)
Width -171/4" (438.2mm)
12 DXi: High Performance Car Speakers
ENGLISH
AMPLIFIER HOOKUP
o
o
NOTE: USE WITH 2 OHM COMPATIBLE AMPLIFIERS.
NOT ALL AMPLIFIERS ARE STABLE INTO A2 OHM LOAD
(ESPECIALLY IN BRIDGED MODE). PLEASE CONSULT
YOUR AMPLIFIER'S OWNER'S MANUAL.
SPECIFICATIONS
DXi112
Type
Frequency Response
Driver Complement
Nominal Impedance
Power Handling (RMS)
Recommended Amplification Range
Power Handling (Peak)
Efficiency
Dimensions
subwoofer enclosure/slot ported
26 Hz - 200 Hz
1- 12" diameter
2 Ohm
360 Watts
50 - 500 Watts
720 Watts
100 dB
Bottom Depth -1811/16" (474.3mm)
Top Depth - 1511/16" (398.1 mm)
Height - 143/4" (374.7mm)
Width -171/4" (438.2mm)
12 DXi: High Performance Car Speakers

ENGLISH
PRECONDITIONING PERIOD
DXi Subwoofers will achieve even greater performance once
they are thoroughly broken in. To break in your new DXi
Subwoofer, play 20 to 30 hours of music at moderate levels.
GET MORE INFORMATION ONLINE AT POLK
UNIVERSITY: www.polkaudiocom/car/faqad/index.php
OPTIMAL CROSSOVER SETTING
We recommend using an active crossover with a 12 to
18dB per octave low pass filter slope, and setting it to
an initial setting of 80 to 90Hz as a good starting point
This is an optimal crossover setting on most vehicles.
INVERTING PHASE
Depending on the placement of your subwoofer enclosure
and associated components, it may be necessary to invert the
phase of one or another of your system's connections in order
to gain better subwoofer/mid-range blending. Inverting the
phase simply means switching the positive connections with
the negative connections at the amplifier. If you choose to do
this, invert the phase of only one set of speakers (either your
mains, or your subs, never both).
LOW FREQUENCY CUT-OFF FOR
MID-RANGE SPEAKERS IN
SYSTEMS WITH SUBWOOFERS
Now that you have a subwoofer in your system, you may
want to decrease the amount of bass going to your midrange
speakers. This will get you better mid-range sound and
increase the power handling. There are two ways to roll off
the bass before it gets to your mid-range speakers. One way
is to use a "bass blocker," a capacitor placed in series with
the speaker input Bass blockers are installed in series,
one end connected with the positive lead from your amplifier
and the other end connected to the positive lead of each of
your speakers. Bass blocker capacitors (200 microfarad @
100V, non-polarized) are available at any Radio Shack or
electronic parts supply house. The other route is to use an
electronic crossover device that allows filtering below 100Hz
or so. Find these devices at your authorized Polk Audio dealer.
Radio/Amp
TECHNICAL ASSISTANCE OR SERVICE
If, after following these hookup and installation directions, you
experience difficulty, please double check all wire connections
Make certain your electronic equipment is operating correctly
by hooking up another speaker to the speaker output For
example, if you are not getting sound from the left channel
speaker, connect the right channel speaker to the left output
If you still get no sound from that side, the problem is in your
amplifier or source electronics. Should you isolate the problem
to the speaker, contact the authorized Polk Audio dealer where
you bought your speakers. Authorized Polk Audio dealers are
the best source for advice and assistance. Polk Audio's
Customer Service Department is available from 9am-6pm, EST,
Monday through Friday, at 800-377-7655
(US & Can only, outside the US call 410-358-3600) Please
do not hesitate to call us if you have questions about your
speaker system.
You will find additional information, informative
articles. manual updates and cool stuff to buy
that has "Polk Audio" all over it by visiting:
www.polkaudio.com.
FRANCAIS
PERIODE DE RODAGE
Les subwoofers DXi seront encore plus performants apres
une periode de rodage convenable. Pour bien roder vos
nouveaux subwoofers, jouez de la musique pour 20-30 heu
res a volume modere. Ensuite allez-y a fond la caisse
l
OBTENEZ PLUS D'INFORMATlON
EN lIGNE A:
www.polkaudio.com/car/faqad/index.php
REGLAGE OPTIMAL D'UN SEPARATEUR
Nous recommandons I'utilisation d'un separateur actif avec
filtre passe-bas regie a une frequence de 80 - 90Hz avec une
pente de 12 a l8dB par octave C'est Ie reglage optimal pour la
plupart des voitures.
INVERSION DE PHASE
Selon I'emplacement de votre subwoofer en relation avec les
autres haut-parleurs, vous devrez peut-etre inverser la phase
d'un des composants de votre systeme pour obtenir un meil-
leur melange subwoofer-mediums. Inverser la phase signifie
tout simplement d'inverser Ie fil positif et Ie fil negatif des
bornes de I'amplificateur. Si vous decidez d'inverser la phase,
n'inversez la phase que d'un seul groupe de haut-parleurs (soit
les haut-parleurs principaux, so it les sub-woofers, jamais les
deux)
COUPURE DES BASSES FREQUENCES ENVOYEES AUX
TRANSDUCTEURS DE MEDIUMS (POUR LES
SYSTEMES UTILISANT UN SUBWOOFER).
Maintenant que votre systeme est muni d'un subwoofer,
vous desirez peut-etre reduire les basses frequences qui
sont envoyees avos transducteurs de mediums. Ceci
ameliorera Ie son des mediums et augmentera leur capacite de
puiss-ance. II ya deux fagons d'attenuer les basses frequences
avant qu'elles n'atteignent les transducteurs de mediums. La
premiere est d'utiliser un filtre-condensateur place a I'entree
du haut-parleur. Ce condensateur est connecte en serie, une
de ses extremites connecte au cable positif de votre ampli-
ficateur et I'autre connecte a la borne positive de votre trans-
ducteur. Ce type de condensateur (200 mfd (microfarad)
@ 100V, non-polarise) est disponible dans la plupart des
magasins d'electronique comme La Source/Radio Shack.
L'autre fagon d'attenuer les basses frequences est d'utiliser
un separateur electronique qu i attenue les frequences sous
les 100Hz. Vous pouvezvous procurer ce type de separateur
chez votre revendeur agree Polk Audio.
+.--------,
Radio/Amp
18 DXi: High Performance Car Speakers
ENGLISH
PRECONDITIONING PERIOD
DXi Subwoofers will achieve even greater performance once
they are thoroughly broken in. To break in your new DXi
Subwoofer, play 20 to 30 hours of music at moderate levels.
GET MORE INFORMATION ONLINE AT POLK
UNIVERSITY: www.polkaudiocom/car/faqad/index.php
OPTIMAL CROSSOVER SETTING
We recommend using an active crossover with a 12 to
18dB per octave low pass filter slope, and setting it to
an initial setting of 80 to 90Hz as a good starting point
This is an optimal crossover setting on most vehicles.
INVERTING PHASE
Depending on the placement of your subwoofer enclosure
and associated components, it may be necessary to invert the
phase of one or another of your system's connections in order
to gain better subwoofer/mid-range blending. Inverting the
phase simply means switching the positive connections with
the negative connections at the amplifier. If you choose to do
this, invert the phase of only one set of speakers (either your
mains, or your subs, never both).
LOW FREQUENCY CUT-OFF FOR
MID-RANGE SPEAKERS IN
SYSTEMS WITH SUBWOOFERS
Now that you have a subwoofer in your system, you may
want to decrease the amount of bass going to your midrange
speakers. This will get you better mid-range sound and
increase the power handling. There are two ways to roll off
the bass before it gets to your mid-range speakers. One way
is to use a "bass blocker," a capacitor placed in series with
the speaker input Bass blockers are installed in series,
one end connected with the positive lead from your amplifier
and the other end connected to the positive lead of each of
your speakers. Bass blocker capacitors (200 microfarad @
100V, non-polarized) are available at any Radio Shack or
electronic parts supply house. The other route is to use an
electronic crossover device that allows filtering below 100Hz
or so. Find these devices at your authorized Polk Audio dealer.
Radio/Amp
TECHNICAL ASSISTANCE OR SERVICE
If, after following these hookup and installation directions, you
experience difficulty, please double check all wire connections
Make certain your electronic equipment is operating correctly
by hooking up another speaker to the speaker output For
example, if you are not getting sound from the left channel
speaker, connect the right channel speaker to the left output
If you still get no sound from that side, the problem is in your
amplifier or source electronics. Should you isolate the problem
to the speaker, contact the authorized Polk Audio dealer where
you bought your speakers. Authorized Polk Audio dealers are
the best source for advice and assistance. Polk Audio's
Customer Service Department is available from 9am-6pm, EST,
Monday through Friday, at 800-377-7655
(US & Can only, outside the US call 410-358-3600) Please
do not hesitate to call us if you have questions about your
speaker system.
You will find additional information, informative
articles. manual updates and cool stuff to buy
that has "Polk Audio" all over it by visiting:
www.polkaudio.com.
FRANCAIS
PERIODE DE RODAGE
Les subwoofers DXi seront encore plus performants apres
une periode de rodage convenable. Pour bien roder vos
nouveaux subwoofers, jouez de la musique pour 20-30 heu
res a volume modere. Ensuite allez-y a fond la caisse
l
OBTENEZ PLUS D'INFORMATlON
EN lIGNE A:
www.polkaudio.com/car/faqad/index.php
REGLAGE OPTIMAL D'UN SEPARATEUR
Nous recommandons I'utilisation d'un separateur actif avec
filtre passe-bas regie a une frequence de 80 - 90Hz avec une
pente de 12 a l8dB par octave C'est Ie reglage optimal pour la
plupart des voitures.
INVERSION DE PHASE
Selon I'emplacement de votre subwoofer en relation avec les
autres haut-parleurs, vous devrez peut-etre inverser la phase
d'un des composants de votre systeme pour obtenir un meil-
leur melange subwoofer-mediums. Inverser la phase signifie
tout simplement d'inverser Ie fil positif et Ie fil negatif des
bornes de I'amplificateur. Si vous decidez d'inverser la phase,
n'inversez la phase que d'un seul groupe de haut-parleurs (soit
les haut-parleurs principaux, so it les sub-woofers, jamais les
deux)
COUPURE DES BASSES FREQUENCES ENVOYEES AUX
TRANSDUCTEURS DE MEDIUMS (POUR LES
SYSTEMES UTILISANT UN SUBWOOFER).
Maintenant que votre systeme est muni d'un subwoofer,
vous desirez peut-etre reduire les basses frequences qui
sont envoyees avos transducteurs de mediums. Ceci
ameliorera Ie son des mediums et augmentera leur capacite de
puiss-ance. II ya deux fagons d'attenuer les basses frequences
avant qu'elles n'atteignent les transducteurs de mediums. La
premiere est d'utiliser un filtre-condensateur place a I'entree
du haut-parleur. Ce condensateur est connecte en serie, une
de ses extremites connecte au cable positif de votre ampli-
ficateur et I'autre connecte a la borne positive de votre trans-
ducteur. Ce type de condensateur (200 mfd (microfarad)
@ 100V, non-polarise) est disponible dans la plupart des
magasins d'electronique comme La Source/Radio Shack.
L'autre fagon d'attenuer les basses frequences est d'utiliser
un separateur electronique qu i attenue les frequences sous
les 100Hz. Vous pouvezvous procurer ce type de separateur
chez votre revendeur agree Polk Audio.
+.--------,
Radio/Amp
18 DXi: High Performance Car Speakers

ENGLISH
SUBWOOFER SPECIFICATIONS
12' 10" 12"
(3048mm) 1254mml (304.8mml
- --_._--------- --_.- _ .. - --- ------------
4 Ohm dual 4 Ohm dual 4 Ohm
Type
Driver Size
Nominal Impedance
.-------
Frequency Response
DXi104 svc
subwoofer
10"
(254mm)
_._---~-----_.
4 Ohm
28-200Hz
DXi124 svc
subwoofer
27-200Hz
DXi104 Dve
subwoofer
28-200Hz
DXi124 Dve
subwoofer
27-200Hz
720 Watts
360 Watts
88dB/series
270 Watts
540 Watts
86dB/series
360 Watts
720 Watts
270 Watts
540 Watts
Power Handling (Watts continuous)
Power Handling (Watts peak)
-_._-- ----- ._---- ._--------------------_._------_.
Sensitivity (SPL at 1 Watt / 1 meter) 86dB 88dB
6"
(1524mm)
63/4"
(171.4mm)
2"
(50 Bmm)
2"
(508mm)
57/16"
(138.1mml
63/16"
(1572mm)
Mounting Depth Bottom Mount
Voicecoil Diameter 2" 2"
(508mm) 150.8mm)
.-.---------_._--_._----
57/16" 6"
(138.1mm) (1524mm)
---------------------------~-
63/16" 6 3/4"
(157.2mm) (1714mm)
Mounting Depth Top Mount
Mounting Diameter
91/16" 11"
(230.2mml (2794mm)
91/16"
(230.2mm)
11"
(2794mml
--------_ .....
Thiele/Small Parameters
._--_.
Fs (Hz)
35Hz 30Hz
Re 3.5 Ohm 3.5 Ohm
Le
3.0mH
3.0mH
Oms
91
104
Oes
0.59 0.46
Ots
0.55 044
---_.
Vas 0.99ft
3
2.54ft
3
(28.3L)
(71.85L)
_._-- -------
Sd 54.25in
2
80.6in
2
(350cm
2)
(520cm
2)
Xmax (Linear) 0.622" 0.622"
(15.8mm) (158mm)
35Hz
3.4 Ohm/coil
34 Ohm/bob.
5.1mH
10.9
0.66
0.62
1.17ft3
33.3L
54.25in
2
(350cm
2)
0728"
(185mm)
30Hz
3.4 Ohm/coil
34 Ohm/bob.
--- ---
5.1mH
10.8
0.49
0.50
3.10ft
3
87.8L
80.6in
2
(520cm
2)
0.728"
(185mm)
WARNING: LISTEN CAREFULLY
Polk Audio loudspeakers and subwoofers are capable of playing
at extremely high volume levels, which could cause serious or
permanent hearing damage. Polk Audio, Inc. accepts no liability
for hearing loss, bodily injury or property damage resulting from
the misuse of its products.
Keep these guidelines in mind and always use your own good
judgment when controlling volume:
• You should limit prolonged exposure to volumes that exceed 85 decibels(dB).
• High volume in an automobile can hinder your ability to safely operate a vehicle.
• You are responsible for knowing the local laws governing acceptable mobile volume levels.
For more about safe volume levels, go to: www.polkaudio.com/education/article/SPU
Or refer to the Occupational Health and Safety Administration (OSHA) guidelines at:
www.osha.gov/dts/osta/otm/noise/standards_more.html
Product Disposal· Certain
international. national and/or local
laws and/or regulations may apply
regarding the disposal of this product.
For further detailed information.
please contact the retailer where you
purchased this product or the
Polk Audio Importer/Distributor in
your country. A listing of Polk Audio
Importer/ Distributors can be found on
the Polk Audio website
www.polkaudio.com or by contacting
Polk Audio at 5601 Metro Drive.
Baltimore. Maryland 21215. USA-
Phone [phone].
22 D Xi: High Per for man ce Car S pea ker s
ENGLISH
SUBWOOFER SPECIFICATIONS
12' 10" 12"
(3048mm) 1254mml (304.8mml
- --_._--------- --_.- _ .. - --- ------------
4 Ohm dual 4 Ohm dual 4 Ohm
Type
Driver Size
Nominal Impedance
.-------
Frequency Response
DXi104 svc
subwoofer
10"
(254mm)
_._---~-----_.
4 Ohm
28-200Hz
DXi124 svc
subwoofer
27-200Hz
DXi104 Dve
subwoofer
28-200Hz
DXi124 Dve
subwoofer
27-200Hz
720 Watts
360 Watts
88dB/series
270 Watts
540 Watts
86dB/series
360 Watts
720 Watts
270 Watts
540 Watts
Power Handling (Watts continuous)
Power Handling (Watts peak)
-_._-- ----- ._---- ._--------------------_._------_.
Sensitivity (SPL at 1 Watt / 1 meter) 86dB 88dB
6"
(1524mm)
63/4"
(171.4mm)
2"
(50 Bmm)
2"
(508mm)
57/16"
(138.1mml
63/16"
(1572mm)
Mounting Depth Bottom Mount
Voicecoil Diameter 2" 2"
(508mm) 150.8mm)
.-.---------_._--_._----
57/16" 6"
(138.1mm) (1524mm)
---------------------------~-
63/16" 6 3/4"
(157.2mm) (1714mm)
Mounting Depth Top Mount
Mounting Diameter
91/16" 11"
(230.2mml (2794mm)
91/16"
(230.2mm)
11"
(2794mml
--------_ .....
Thiele/Small Parameters
._--_.
Fs (Hz)
35Hz 30Hz
Re 3.5 Ohm 3.5 Ohm
Le
3.0mH
3.0mH
Oms
91
104
Oes
0.59 0.46
Ots
0.55 044
---_.
Vas 0.99ft
3
2.54ft
3
(28.3L)
(71.85L)
_._-- -------
Sd 54.25in
2
80.6in
2
(350cm
2)
(520cm
2)
Xmax (Linear) 0.622" 0.622"
(15.8mm) (158mm)
35Hz
3.4 Ohm/coil
34 Ohm/bob.
5.1mH
10.9
0.66
0.62
1.17ft3
33.3L
54.25in
2
(350cm
2)
0728"
(185mm)
30Hz
3.4 Ohm/coil
34 Ohm/bob.
--- ---
5.1mH
10.8
0.49
0.50
3.10ft
3
87.8L
80.6in
2
(520cm
2)
0.728"
(185mm)
WARNING: LISTEN CAREFULLY
Polk Audio loudspeakers and subwoofers are capable of playing
at extremely high volume levels, which could cause serious or
permanent hearing damage. Polk Audio, Inc. accepts no liability
for hearing loss, bodily injury or property damage resulting from
the misuse of its products.
Keep these guidelines in mind and always use your own good
judgment when controlling volume:
• You should limit prolonged exposure to volumes that exceed 85 decibels(dB).
• High volume in an automobile can hinder your ability to safely operate a vehicle.
• You are responsible for knowing the local laws governing acceptable mobile volume levels.
For more about safe volume levels, go to: www.polkaudio.com/education/article/SPU
Or refer to the Occupational Health and Safety Administration (OSHA) guidelines at:
www.osha.gov/dts/osta/otm/noise/standards_more.html
Product Disposal· Certain
international. national and/or local
laws and/or regulations may apply
regarding the disposal of this product.
For further detailed information.
please contact the retailer where you
purchased this product or the
Polk Audio Importer/Distributor in
your country. A listing of Polk Audio
Importer/ Distributors can be found on
the Polk Audio website
www.polkaudio.com or by contacting
Polk Audio at 5601 Metro Drive.
Baltimore. Maryland 21215. USA-
Phone [phone].
22 D Xi: High Per for man ce Car S pea ker s

LIMITED WARRANTY
Polk Audio, Inc. warrants the original purchaser only that this
Polk Audio DXi Subwoofers Product (the Product) will be free
from defects in materials and workmanship for a period of
(1) one year from the date of original retail purchase from
a Polk Audio Authorized Dealer. However, this warranty will
automatically terminate prior to the expiration of the (1) one
year period if the original retail purchaser sells or otherwise
transfers the Product to any other party. The original retail
purchaser shall herein after be referred to as "you." To allow
Polk Audio to offer the best possible warranty service, please
fill out the Product Registration Card(s) and send them to the
Factory at the address provided in the Registration Card
within (10) ten days of the date of purchase.
Defective Products must be shipped, together with a proof of
purchase, prepaid insured to the Authorized Polk Audio Dealer
from whom you purchased the Product, or to 1 Viper Way,
Vista, California 92081. Products must be shipped in the
original shipping container or its equivalent; in any case
the risk of loss or damage in transit is to be borne by you.
If, upon exam-ination at the Factory or Polk Audio Authorized
Dealer it is determined that the unit was defective in materials
or workmanship at any time during the Warranty period,
Polk Audio or the Polk Audio Dealer will, at its option, repair
or replace this Product at no additional charge, except as set
forth below. All replaced parts and Products become property
of Polk Audio. Products replaced or repaired under this
Warranty will be returned to you, within a reasonable
time, freight prepaid.
This Warranty does not include service or parts to repair
damage caused by accident, disaster, misuse, abuse,
negligence, inad-equate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maxi-
mum of the unit, cosmetic appearance of the cabinetry not
directly attributable to defects in materials or workmanship,
or service, repair, or modifications of the Product which
has not been authorized or approved by Polk Audio.
This Warranty is in lieu of all other expressed Warranties.
If this Product is defective in materials and workmanship as
warranted above, your sole remedy shall be repair or replace-
ment as provided above. In no event will Polk Audio, Inc. be
liable to you for any incidental or consequential damages
arising out of the use or inability to use the Product, even
if Polk Audio, Inc. or a Polk Audio Dealer has been advised
of the possibility of such damages, or any other claim by any
other party. Some states do not allow the exclusion or
limitation of consequential damages, so the above limitation
and exclusion may not apply to you. This Warranty gives you
specific legal rights which may vary from state to state.
This warranty applies only to Products purchased in the United
States of America, its possessions, and US and NATO armed
forces exchanges and audio clubs. The Warranty terms and
conditions applicable to Products purchased in other countries
are available from the Polk Audio Authorized Distributors
in such countries.
28 D Xi: Hi gh Per for man ce Car S pea kers
LIMITED WARRANTY
Polk Audio, Inc. warrants the original purchaser only that this
Polk Audio DXi Subwoofers Product (the Product) will be free
from defects in materials and workmanship for a period of
(1) one year from the date of original retail purchase from
a Polk Audio Authorized Dealer. However, this warranty will
automatically terminate prior to the expiration of the (1) one
year period if the original retail purchaser sells or otherwise
transfers the Product to any other party. The original retail
purchaser shall herein after be referred to as "you." To allow
Polk Audio to offer the best possible warranty service, please
fill out the Product Registration Card(s) and send them to the
Factory at the address provided in the Registration Card
within (10) ten days of the date of purchase.
Defective Products must be shipped, together with a proof of
purchase, prepaid insured to the Authorized Polk Audio Dealer
from whom you purchased the Product, or to 1 Viper Way,
Vista, California 92081. Products must be shipped in the
original shipping container or its equivalent; in any case
the risk of loss or damage in transit is to be borne by you.
If, upon exam-ination at the Factory or Polk Audio Authorized
Dealer it is determined that the unit was defective in materials
or workmanship at any time during the Warranty period,
Polk Audio or the Polk Audio Dealer will, at its option, repair
or replace this Product at no additional charge, except as set
forth below. All replaced parts and Products become property
of Polk Audio. Products replaced or repaired under this
Warranty will be returned to you, within a reasonable
time, freight prepaid.
This Warranty does not include service or parts to repair
damage caused by accident, disaster, misuse, abuse,
negligence, inad-equate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maxi-
mum of the unit, cosmetic appearance of the cabinetry not
directly attributable to defects in materials or workmanship,
or service, repair, or modifications of the Product which
has not been authorized or approved by Polk Audio.
This Warranty is in lieu of all other expressed Warranties.
If this Product is defective in materials and workmanship as
warranted above, your sole remedy shall be repair or replace-
ment as provided above. In no event will Polk Audio, Inc. be
liable to you for any incidental or consequential damages
arising out of the use or inability to use the Product, even
if Polk Audio, Inc. or a Polk Audio Dealer has been advised
of the possibility of such damages, or any other claim by any
other party. Some states do not allow the exclusion or
limitation of consequential damages, so the above limitation
and exclusion may not apply to you. This Warranty gives you
specific legal rights which may vary from state to state.
This warranty applies only to Products purchased in the United
States of America, its possessions, and US and NATO armed
forces exchanges and audio clubs. The Warranty terms and
conditions applicable to Products purchased in other countries
are available from the Polk Audio Authorized Distributors
in such countries.
28 D Xi: Hi gh Per for man ce Car S pea kers

polkaudio~
This is your Product Model and Serial Number.
Enter this number in the "Serial Number" space
when registering your product online. Keep
this card handy for Model and Serial Number
reference when calling Polk Customer Service.
Register Your New Polk Audio Product
Online NOW for a Chance to win
$500 of Polk Product
www.polkaudio.com/registration/
Become a valued member of the Polk Family and get a chance to win " • •• ,
II fe,
~ Creates a permanent record of your purchase, in case you misplace your original receipt.
~ Enters you in our monthly FREE drawing for $500-worth of Polk Audio Speakers.
~ Allows you to enroll in Club Polk: for informative Polk Website Forums, special discounts
in the Polk Webstore, advance notice of Polk Promos, and discounts on Authorized
Polk Audio parts.
~ Keeps y~u up to date when there is news and announcements about your product.
~ Gives you the option to I'opt-in" for Polk Audio's Audio Enjoyment Enhancers:
Our Monthly Emails, with news, reviews and tips on everything audio; and our
FREE Polk Audio Newspaper.
We take your privacy seriously. Polk Audio does not share or sell
infonnation to any other parties, unless directed by court order.
Registering your product has no effect on your warranty.
Warranties apply as stated in your product manual.
Please be sure to keep your original purchase receipt.
Questions? ,Concerns? Contact Polk Audio Customer Service, 9am - 6pm, M-F, EST (USA)
800-317-1655 US & Canada only • 410-358-3600 outside US & Canada • [email protected]
RM0320-7
polkaudio~
This is your Product Model and Serial Number.
Enter this number in the "Serial Number" space
when registering your product online. Keep
this card handy for Model and Serial Number
reference when calling Polk Customer Service.
Register Your New Polk Audio Product
Online NOW for a Chance to win
$500 of Polk Product
www.polkaudio.com/registration/
Become a valued member of the Polk Family and get a chance to win " • •• ,
II fe,
~ Creates a permanent record of your purchase, in case you misplace your original receipt.
~ Enters you in our monthly FREE drawing for $500-worth of Polk Audio Speakers.
~ Allows you to enroll in Club Polk: for informative Polk Website Forums, special discounts
in the Polk Webstore, advance notice of Polk Promos, and discounts on Authorized
Polk Audio parts.
~ Keeps y~u up to date when there is news and announcements about your product.
~ Gives you the option to I'opt-in" for Polk Audio's Audio Enjoyment Enhancers:
Our Monthly Emails, with news, reviews and tips on everything audio; and our
FREE Polk Audio Newspaper.
We take your privacy seriously. Polk Audio does not share or sell
infonnation to any other parties, unless directed by court order.
Registering your product has no effect on your warranty.
Warranties apply as stated in your product manual.
Please be sure to keep your original purchase receipt.
Questions? ,Concerns? Contact Polk Audio Customer Service, 9am - 6pm, M-F, EST (USA)
800-317-1655 US & Canada only • 410-358-3600 outside US & Canada • [email protected]
RM0320-7