Polygroup Home Heritage TG70CH119P00 User manual

MADE IN CHINA
1
ASSEMBLY INSTRUCTIONS
TREE ASSEMBLY INSTRUCTIONS
Fig. B - Tree and Light Assembly
Congratulations on purchasing your new tree from Polygroup®! This tree comes with Quick Set®
technology - it takes less than 10 minutes to set up and light up!
Carefully follow the instructions below on how to quickly and easily set up your new tree:
1. Choose a level surface near a wall outlet.
2. Assemble the tree stand (See Fig. A).
MODEL #: TG70CH119P00
Do Not Tamper
Internal Parts
Open the
protective
cap
Do Not Tamper
Internal Parts
Open the
protective
cap
Tree Top
Section 2
Section 1
3. Identify all tree sections (See Fig. B) by the stickers on them, and start assembling from bottom to top.
4. Open the protective cap of pole, and insert the pole into the stand. Allow all branches fall down into
place. Check to make sure that all wires are free from branch hinges.
5. Shape the tree section one branch at a time. Start with the tips closest to the pole and move outwards.
Fan all the tips out in alternating directions, and slightly upsweep them for a natural look (See Fig. C).
6. Repeat Step 4 and 5 for the upper tree section(s) until tree top is installed and shaped.
7. Connect plug with adaptor, and plug it in to the wall outlet as indicated in Fig. B.
8. Step back and view your tree. Shift branches to fill any gaps.Your Christmas tree is now ready to be
decorated.
Top view Side view
Fig. C
*Electrical Rating For The Tree
(For Indoor Use Only)
Input: 120V, 60Hz, 0.83A
Output: 24V DC 2A
Plug Adaptor
Into Wall
Outlet
Insert Green Label
Plug into Adaptor
Fig. A - Tree Stand Assembly
Click
Pull apart the legs of the stand so that they
are snapped into an x-shape, place the tree
stand on a level surface.
To close the stand, press the metal button
and fold the legs together.

MADE IN CHINA
2
ASSEMBLY INSTRUCTIONS
This tree includes sets of hinge pins & washers, and spare bulbs. If extra parts are needed, please contact
our customer service center.
SPARE PARTS
STORAGE INSTRUCTIONS
TROUBLESHOOTING TIPS
1. Unplug from power source, and detach plug from adaptor. Remove all ornaments and decorations.
2. Disassemble the tree from top to bottom. Gently lift pole straight up to remove from the lower section,
and fold all branches toward the pole.
3. Close the protective caps on the poles to avoid damaging the internal
parts (See Fig. D).
4. Place the disassembled tree into the shipping box and tape it shut.
5. Store your tree in a cool, dry place away from sunlight.Exposure to
excessive heat or humidity may damage your tree.
If Tree Does Not Illuminate / Some Bulbs Do Not Light or Flicker
1. Check to make sure that all plugs and adaptor are properly connected as indicated in Fig. B.
2.Turn the poles gently to make sure pole-to-pole connection is secured.
3. Check for loose, broken or missing bulbs, and replace as needed (See LAMP REPLACEMENT).
1. Place the branch into the hinge bracket (See Fig. E).
2. Insert a new hinge pin all through the holes of bracket,
and secure with a washer (See Fig. E - close up).
Loose Hinge Pin
Fig. E
Fig. D
Lamp Replacement
Step 1. Unplug from power source, by pulling out the adaptor itself - do not pull on the power cord.
(For reference only)
Step 3. Replace with a new spare
LED lamp (included).
Step 2. Lift up the lamp lock tab,
and pull the bulb and its
plastic base straight out
from the lampholder.
CAUTION:
1. Risk of fire. Use only the power adaptor provided with this product. Do not replace lamps with other
than the spare lamps provided with this product.
2.To reduce the risk of fire and electric shock:
a. Do not mount or support light strings in a manner that can cut or damage wire insulation, and
b. Use only the power supply cord provided with this product.

MADE IN CHINA
3
ASSEMBLY INSTRUCTIONS
1. Slide open the battery cover.
2. Replace with a new CR2032 button cell battery
with correct polarities (+/-) as indicated.
3. Slide the battery cover closed.
Battery Replacement
REMOTE CONTROL INSTRUCTIONS
Multi Color Steady Glow
Color Wheel
Speed Up
Speed Down
ON/OFF
Warm White Steady Glow
Brightness Up
Next Preset Motion Effect
Previous Preset Motion Effect
Brightness Down
Remove insulation
tab before use.
Battery Cover
1. Remove the insulation tab before use.
2. Tap to turn lights ON or OFF.
3. Tap the Color Wheel to display all lights in one-color steady glow. Sweep around the color wheel
to select your desired color.
4. Tap to display all lights in warm white steady glow.
5. Tap to display all lights in multi color steady glow.
6. Tap or to select from the 10 preset motion effects:
• Warm White Twinkle
• Color Twinkle
• Fading
• Multi Ball
• Color Switching
• Collision
• Wave
• Waterfall
• Rainbow Shower
• Rainbow
7. Tap or to adjust the speed of motion effect.
8. Tap or to adjust the brightness of lights.
WARNING
1. SMALL PARTS, KEEP AWAY FROM CHILDREN.
2. Do not expose the product to moisture.
3. Remove batteries when not used for an extended period of time, or when depleted.
4. Dispose of used batteries properly by following directions on batteries.
5. Use only CR2032 batteries for the remote controller.
6. Clean the battery contact surfaces gently prior to battery installation.
7. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.

MADE IN CHINA
4
ASSEMBLY INSTRUCTIONS
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroupstore.com. One of our customer service
representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX. TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address (No P.O.Boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem: