Polygroup TG46M6159C00 User manual

Slide the legs up into the slots
of the base on the trunk on
the Bottom Section until
firmly secured.
Fig. A - Tree Stand Assembly
Connect Red
Label Plugs
TREE ASSEMBLY INSTRUCTIONS
Congratulations on purchasing your new tree from Polygroup®!
Carefully follow the instructions below on how to assemble your new tree quickly and at ease:
1. Choose an appropriate location near a wall outlet.
2. Assemble the tree stand (Fig. A) and place on a level surface.
3. Assemble the tree from the bottom to the top. Insert the pole of the tree top into Tree Bottom until firmly secured. Be sure that all
wires are free of branch hinges.
4. Connect the red label plugs, and then insert green label plug into the wall outlet (Fig. B).Your entire tree should now be lit.
5. Shape the tree from the bottom to the top. Start with the branches farthest from the pole – fan out in a star shape (Fig. C), and
continue until the entire tree is shaped.
6. Slightly upsweep all tips for a fuller, uniform look. Shift branches to fill in any gaps.Your Christmas tree is now complete and
ready to be decorated.
MODEL #: TG46M6159C00 2020 TREE LETTER "A"
Fig. B - Tree and Light Assembly *Electrical Rating For The Tree
(For Indoor Use Only)
0.68A 120V, 60Hz
Tree Top
Tree Bottom
Top view Side view
Fig. C
SKU # 5064431
Insert
Green Label
Plug Into Wall
Outlet
NEED HELP?
DO NOT RETURN TO STORE. PLEASE VISIT US AT:
www.polygroupstore.com OR 1-888-919-0070
1

STORAGE INSTRUCTIONS
1. Unplug from the wall outlet, and disconnect the red label plugs.Then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Gently lift the pole straight up to remove from the section below, and fold all
branches toward the pole.
NOTE: In case of difficulty separating the poles, apply a small amount of lubricant at the joint, rotate the upper pole in both
directions, and lift the upper pole again.
3. Carefully place all tree sections into the shipping box and tape it shut.
4. Store your tree in a cool, dry place away from sunlight. Exposure to excessive heat or humidity may damage your tree.
5. Keep out of reach of pets and children.
SPARE PARTS
This tree includes hinge pins/washers, and spare bulbs and fuses.
If extra parts are needed, please contact our customer service center.
2
TROUBLESHOOTING TIPS
If The Tree Does Not Illuminate / Some Bulbs Do Not Light or Flicker
1. Check to make sure that all plugs and poles are properly and firmly connected as indicated in Fig. B and assembly instructions.
2. Disconnect from power source, then check for loose, broken or missing light bulbs and replace as needed.
3. Disconnect from power source, then check for blown fuses and replace as needed.
NOTE: Please make sure to use appropriate spare fuses as indicated on the label plug.
Loose Hinge Pin
1. Extra hinge pins are included for repairing the hinges.
Place the branch into the slot of the bracket.
2. Insert a new hinge pin through the hole and secure
using the retainer washer. (See Fig. D)
Fig. D
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact us at 1-888-919-0070
or visit our website at www.polygroupstore.com. One of our customer service representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
Distributed by: Hobby Lobby Stores, Inc. • Oklahoma City, OK 73179 • www.hobbylobby.com