Polygroup TG60P3D94L01 Manual

pre-lit tree
INSTRUCTIONS GUIDE

2
attention
Class B Disclaimer: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
READ AND FOLLOW ALL THE SAFETY INSTRUCTIONS.
This decorative item is not intended for use by persons (including children ) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been giving supervision.
Children should be monitored to ensure that the items are not used as toys.
CAUTION and essentially the following: To reduce the risk of fire and electric shock.
Disconnect the power supply from the decorative item before carrying out any maintenance or cleaning activites.
Do not use the decorative item outdoors.
Do not install or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
Disconnect the appliance when leaving the house, when retiring or if left unattended.
Do not hang ornaments or other objects to the cord, cable or series of lights.
Do not cover the decorative item with a cloth, paper or any material that is not part of the product when it is in use.
Do not install the string lights so that the insulation of the cable can be cut or damaged.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Please note that changes or modifications of this product not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
WARNING!
Do not connect the chain to the supply while it is in the packing.
The connecting cable cannot be repaired or replaced. If the cable is damaged the entire fitting must be discarded.
This product may potentially trigger seizures for people with photosensitive epilepsy when using the motion effect light modes.
NON-REPLACEABLE BULB.
Do not connect this chain electrically to devices from another manufacturer.
CAUTION! For indoor use only.
The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in
accordance with local environmental regulations for waste disposal.
Power supply: see label
Single LED luminous flux: red 600 mcd, green 1500 mcd, blue 500 mcd
Technical Specifications

3
physical set up
a. b.

4
c. d.
e. f.

5
1.

6
1. Assemble the tree as shown in pictures
2. Plug the power adapter into an AC outlet
The tree will illuminate with default effects
3.
Button: Switch between preset effects/reset
2. 3.
BUTTON
LED INDICATOR
• CONTINUOUS GREEN: AP mode, connected
• FLASHING GREEN: AP mode, no device connected
• CONTINUOUS BLUE: Wi-Fi mode, connected
• FLASHING BLUE: Wi-Fi mode, connection in progress
• FLASHING RED: Wi-Fi mode, unable to connect
• GREENISH BLUE: SETUP MODE (Bluetooth ON)
• YELLOW: Firmware Update in progress
• CONTINUOUS RED: General error
• FLASHING WHITE: Reset procedure in progress

7
app download
1. 3.2.
Twinkly
GET
Twinkly Cancel
Twinkly
Lifestyle
30
1. Go to App Store/Google Play (by scanning the QR code)
2. Download and install the “Twinkly” app
3. Ensure that the Twinkly app is correctly installed on your smartphone

8
set up twinkly
1. 2.
Bluetooth
Bluetooth
Bluetooth
Bluetooth
Twinkly
1. Make sure Bluetooth is turned on
2. Open the Twinkly app and select GENERATION II controller for your tree
Choose your Twinkly!
Generation I
(2 Feedback LED)
(1 Feedback LED)
Generation II

9
Configure
3. 4.
Connecting...
Insert your Wi-Fi password
Home Internet
xxxxxxxxxx
5.
5
sec
SKIP SETUP
Configure your Twinkly
Configuring Twinkly with
Please select the LED count of your Twinkly
If you’re not sure, please see the number under the
Twinkly controller
210 270 330
390 435 480
540
750
600 660
Configure
Insert your Wi-Fi password
Home Internet
xxxxxxxxxx
3. Press and hold the controller button until the LED is GREENISH BLUE (approx 5 sec)
4. Select your local Wi-Fi network and enter the password
5. Select the correct light count of your tree and tap "Configure" to complete the connection
to your Twinkly tree
If you do not have access to a local Wi-Fi network, connect directly to your smartphone
Wi-Fi by following the instructions in the “Troubleshooting” section