Polytron TSM 1000 HD-C User manual

TSM 1000 HD-C
TSM 1000 HD-CF
User Manual
MADE IN GERMANY
0901743 V1

2
Table of contents
Page
1. Hazard and safety information 3
2. General 5
3. Description 5
4. Scope of supply 5
5. Input circuit 5
6. Assembly 6
6.1 Earthing (grounding) 6
7. Installation 6
7.1 TSM-HD-C input assignment 7
7.2 Input level 8
7.3 Output level 8
8. Programming, general 9
8.1 Software installation 9
8.1.1 Installing the driver 9
8.1.2 Installing the programming software 10
8.2 Programming the device parameters 10
8.2.1 Input parameters 11
8.2.2 Output parameters 13
8.3 Saving the programs 15
8.3.1 Saving the settings 15
8.3.2 Loading the settings 15
8.5 LED evaluation 16
8.6 Firmware update 17
8.6.1 CPU (micro-controller) 17
9. Application examples 18
9.1 TSM-HD-C 18
10 Technical data 20
11. Declaration of Conformity 22
12 Default assignment 23

3
1. Hazard and safety information
Power supply and power cord
The device must be operated only at a power supply with a voltage
of 230 V / 50 Hz.
Connection cable
Place the connection cable always trip proof !
Replace the power cord only with an original power cord.
Potential equalization / grounding
Proper grounding and installation of the device must be carried out according to EN 60728-11 / VDE
0855-1 regulations.
Operation without grounding or potential equalization of equipment is not allowed.
Humidity and placement location
The device must not be exposed to dripping or splashing water. If water condensation occurs, wait
until the device is completely dry. The device must be installed on a vibration-free location.
Ambient temperature and heat effect
The maximum allowable ambient temperature is 50 ° C.
The ventilation holes of the device must NOT be covered under any circumstances. Too much heat
or heat accumulation affect the life of the device and can be a source of danger.
To prevent heat buildup and to ensure good ventilation, the device must be mounted horizontally (eg.
on a wall). The device must not be mounted above, on top, or near heat sources (e.g radiators,
heating plants), where the device is exposed to heat radiation or oil vapors. The installation must be
done only in rooms that ensure compliance with the permissible ambient temperature range, even
under changing climatic conditions.
Warning:
When installed in rooms such as storage or attic one should pay particular attention on compliance
with the ambient temperature. Because of the danger of fire due to overheating or lightning strike, it
is recommendable to install the device on a noncombustible surface. Combustible surfaces are wood
beams or bars, wood boards, plastic materials, etc.
Conditions to ensure electromagnetic compatibility (EMC)
All covers, screws and connectors must be securely mounted and tightened, contact springs must
not be bent or oxidized.

4
Opening the case
ATTENTION Device’s case opening and repairs must be performed only by authorized
personnel. First to be done is to pull the network plug. Replacing of fuses must be
done only with fuses of same type, value and melting characteristics.
No maintenance work during storms
ATTENTION
This module contains ESD components! (ESD = Electrostatic Sensitive Device). An
electrostatic discharge is an electrical current pulse, which can flow also through an
electrically insulated material, when triggered by large voltage difference.
To ensure the reliability of ESD components, it is necessary to consider their most important
handling rules:
Electrostatic sensitive components can be processed only on electrostatic protected area (EPA)!
Pay attention permanently to potential equalization (equipotential bonding)!
Use wrist straps, approved footwear for personnel grounding!
Avoid electrostatically chargeable materials such as normal PE, PVC, polystyrene!
Avoid electrostatic fields >100 V/cm !
Use only labeled and defined packing and transportation materials!
Damage caused by faulty connections and / or improper handling are excluded from
any liability.
Waste disposal
Electronic equipment is not household waste but should be properly disposed on electrical and
electronic equipment waste - in accordance with Directive 2002/96/EC OF THE EUROPEAN
PARLIAMENT AND COUNCIL.
Please take this device at the end of its use for proper disposal at the designated public collection
points.
WEEE-Reg.-Nr. DE 51035844

5
2. General
With the TSM 1000 HD-C, any desired DVB-S/S2 satellite transponder is converted from its original
frequency range to a user-defined SAT IF frequency raster. Any transponders that are not desired
are thus ruled out. The outputs of multiple devices can be interconnected via a distributor at the
output. Each channel strip has an automatic gain control (AGC), so that all the transponders (even if
there are level fluctuations at the input) are in line with the system level set at the output.
The TSM 1000 HD CF is equipped with a built-in TSM SAB 09 filter.
3. Description
The TSM 1000 HD-C.. implements any 10 DVB-S or DVB-S2 transponders (QPSK / 8PSK) in any 10
output frequencies in the SAT IF range. The output frequency range can be individually adjustable
from 950 to 2150 MHz. This frequency range can be fed into an existing, satellite-grade coaxial
distribution network. It does not matter if it is a network with a star, tree or mixed structure.
Viewers can receive all the TV channels located on the transponders via a commercially available
DVB-S/S2 receiver or a TV set with an integrated DVB-S/S2 tuner. It does not matter whether the
individual channels are broadcast in HDTV, as pay TV or as free-to-air signals.
Programming is performed using a laptop or a desktop PC. This is connected to the USB connector
via the USB cable (supplied). The TSM 1000 HD-C.. can be quickly and easily programmed using a
graphical user interface.
4. Scope of supply
1 x TSM 1000 HD-C.. (TSM 1000 HD-CF: with built-in TSM SAB 09 filter).
1x Power cable
1x USB cable
1x USB flash drive (programming software)
1x User manual
1x Mounting accessories
1x Drilling template
5. Input circuit
Four freely selectable SAT IF signals can be switched to the 10 tuners with the 4 in 10 switching
matrix. The power supply for the LNB is available directly from the input tuner at inputs 1 and 4.

6
6. Assembly
The TSM 1000 HD-C must be assembled in a well-ventilated room. The ambient temperature
must not exceed 50°C. Ensure that air can circulate through the ventilation holes. There must
be a minimum distance of 15 cm around the unit to allow air to circulate freely. To perform
any assembly work or when working on the cabling, the power plug must first be unplugged.
6.1 Earthing (grounding)
The device must be earthed in accordance with EN 60728-11.
- Strip off approx. 15 mm of the cable insulation from the earthing cable (4 mm²).
- Slip the end from which the insulation has been stripped under the earthing screw and tighten the
screw securely.
15 cm
15 cm
Earthing screw

7
7. Installation
Remove the screws and take off the cover, lifting it upwards.
Connect the various SAT levels to the four inputs (SAT 1, SAT 2, SAT 3, and SAT 4).
Levels from different LNBs can also be connected.
The LNB voltage is fixed at inputs 1 and 4.
The current consumption of the LNBs connected must not exceed 250 mA per input.
Please note that a digital-grade Quattro LNB (e.g. a Polytron OSP AP 94) should be used.
If the LED for the LNB supply is not lit, the LNB supply will be interrupted or disrupted.
Please note:
The overall current consumption of all the LNBs connected must not exceed 500mA.
7.1 TSM 1000 HD-C input assignment
The inputs and outputs of the device are pre-programmed at the factory with a standard frequency
assignment (see the extra sheet). This assignment is adapted to the usage of the TSM SAB 09
(already installed in the TSM HD CF).
In order to receive the pre-programmed ASTRA transponders, the satellite inputs must be connected
as shown in the following diagram.
Assignment during pre-programming
1
HH 2 VH 3 HL 4 VL
DC
DC
DC
DC

8
7.2 Input level
To ensure good reception, make sure that the level at the inputs is between 60 and 80 dBµV.
When receiving digital signals, it is better to have a level that is too low rather
than one that is too high.
Use an attenuator with high input levels
7.3 Output level
The output level is 90 dBµV when supplied. This can be changed
by programming the device (see Point 9.2.2)
Output/OUT USB LED
8 Programming in general
After connecting the power supply cable, the device runs through an internal routine, and all 10
channels are set to the data previously stored. During this time, the Status LED next to the USB
socket will flash green.
A connection between the TSM HD-C 1000 and the laptop or PC is only possible once the status
LED is permanently illuminated green .
The programming software
must first be installed on the laptop
or PC before this is connected to
the TSM 1000 HD-C
USB
LED

9
8.1 Software installation
Download the software package (SATIF10.zip) from the www.polytron.de homepage and unzip it
to any directory (e.g. C:\TSM1000HDC ).
The software can also be downloaded from the USB flash drive (supplied).
8.1.1 Installing the driver
Start Instal_driver.cmd
Follow the instructions on the screen.
With some initial installations, the following dialog may appear. This depends on the operating
system. Follow the subsequent instructions and tick the check boxes:
No, not now
Next
Automatically install the software
Next
If this information is shown:
continue installation

10
The installation of the driver software is now complete.
8.1.2 Installing the programming software
Install the software in the desired folder by launching the “Setup.exe” program.
Follow the instructions on the screen.
Close the screen displays when the installation is complete.
The TSM 1000 HD-C may be connected to the computer with the USB cable
once the programming software has been installed on the computer.
8.2.0 Programming the device parameters
Launch the – SATIF10 – program
Click the top left
Menu
The following menu items will be available:
•Program Menu
•Firmware Update
•Exit
All the settings of the input and output parameters are made in the “Program Menu”. After calling
up the menu, all 10 channels will be queried and the respective set parameters will be displayed.
The software for the
following hardware has
been installed
Proceed