PondMAX PV350L User manual

PMAX PV350L Instructions.indd 3 29/10/21 5:56 am
PV350L
POND / OUTDOOR VACUUM
INSTRUCTION MANUAL
DATE
OCT 2021 v1.0 www.pondmax.com.au
MODEL
03OV234

PMAX PV350L Instructions.indd 4 29/10/21 5:56 am
P O N D M A X . C O M . A U
WELCOME TO THE WORLD OF PONDMAX™.
YOU MADE THE RIGHT CHOICE INVESTING IN THIS
QUALITY PRODUCT. THANK YOU AND ENJOY.
BEFORE USING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY AND MAKE
YOURSELF FULLY FAMILIAR WITH THE UNIT. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE
FOR FUTURE REFERENCE.
TECHNICAL SPECIFICATIONS
DESCRIPTION PV350L
CONTAINER SIZE (L) 35
SUCTION PRESSURE (kPa)
18
POWER (W)
1400
VOLTS (V)
240
CABLE LENGH (M)
10
DESCRIPTION & FEATURES
Your PondMAX Pond/Outdoor Vacuum has been manufactured with advanced technology to provide you a convenient,
painless and efficient solution for routine cleaning of your pond and waterfeature.
•
This multi-function pond vacuum can be used for either wet or dry applications.
•
Comes with a range of nozzles and accessories to meet the most demanding applications.
•
Equipped with a 4.5m suction hose and 1.5m discharge hose (for wet applications). A 10m power cable further
compliments the features and convenience of this vacuum.
•
Caster wheels allow for easy transportation and use around your yard.
•
Features an automatic fill/drain system as well as a large 35L container holding capacity.
•
2 Year warranty, see WARRANTY AGAINST DEFECTS clause.
ASSEMBLY
•
Loosen and disconnect the vacuum tank clamps (x2)
and remove motor head. Remove all parts from inside
of the container as well as any contents remaining in
the original box.
•
Connect the intake filter to the bottom portion of the
motor head. With the drawstring positioned at the
higher point-tighten firmly.
•
Install plastic feet into notches on the outside of the
vacuum container. Once feet are installed use provided
screws to attach feet firmly to tank.
•
Insert castor wheels into the bottom of the plastic feet
while applying pressure.
•
Replace the motor head back onto container and lock
the clamps.
•
Connect the end of suction hose into the upper port of
the vacuum container and lock into place by twisting
lightly to the right.
•
On the opposite end of the suction hose, connect the
clear and black extension rods firmly into each other
and fit desired suction nozzle onto opposite end.
•
For wet use remove the drain cap at the bottom of the
vacuum container and thread the end of the discharge
hose onto the bottom port on the container.
•
The hose end with one way flapper should be away
from the vacuum at farthest point. The waste filter bag
attaches to the end with flapper using the squeeze
clamps to hold firmly.
•
For dry use, keep drain cap connected to the bottom
port on vacuum container (Do not connect discharge
hose).

PMAX PV350L Instructions.indd 5 29/10/21 5:56 am
MAINTENANCE
•
Your PondMAX vacuum requires very little maintenance.
However the container, foam intake filter and waste
filter bag should periodically be rinsed to rid of
lingering sludge or debris. Occasional inspection of the
hoses is also recommended.
•
Always switch off the vacuum cleaner at the main
switch and unplug cable from power source, before any
maintenance is performed.
•
Remove all hoses and the motor head from container.
•
Rinse the container with a garden hose until all sludge
or debris has been removed.
•
Pull the foam intake filter and waste filter bag off. Rinse
with garden hose until all sludge or debris has been
removed.
•
While the intake filter is off, always inspect the float for
free movement.
•
Once the vacuum and components are clean, put the
vacuum back together inspecting the hoses and suction
rods carefully for possible damage.
OPERATION IN WET APPLICATION
•
Set up the vacuum as near to the pond or waterfeature
as possible. Make sure the vacuum is standing firmly to
prevent tipping.
•
Attention: The vacuum is designed to be positioned
above the water level during operation, to assure
proper drain function.
•
Position the end of the discharge hose in such a manner
that the discharged water is diverted to a remote
location, away from pond (e.g. garden, flower bed). Lay
the discharge hose flat on the ground (or if possible
with a slight incline downward).
•
Make sure that the waste filter bag is fastened securely
to the end of the discharge hose so that large particles
are contained.
•
Connect the vacuum power cable to the mains power
source.
•
Insert one of the supplied nozzles into the end of the
suction hose/rods.
•
Power on the vacuum at the switch on the motor head,
using the “II” switch setting. This setting automatically
cycles the fill/drain system. Vacuum has an initial 10
second delay before motor starts, 50 second suction
time and 50 second emptying time. The motor will then
shut off for 50 seconds and will repeat cycle.
•
While vacuum is running, apply vacuum directly to
debris using slow and even movements. Keep the
vacuum hose below waist level for best performance.
When the vacuum container has reached its maximum
liquid level, the vacuum will stop sucking automatically.
The one way flapper at the end of the discharge hose
will open and the debris will exit the vacuum container
until empty. Operation from this point on depends on
the switch setting used,
•
When operation is complete switch off vacuum,
positioning switch centrally to ‘O’.
OPERATION IN DRY APPLICATION
•
Set up the vacuum as near as possible to where vacuum
will be used. Make sure the vacuum is standing firmly to
prevent tipping.
•
Loosen and disconnect the vacuum container clamps
and remove motor head. Install paper dust bag firmly
onto the suction port on the inside of the container.
Reinstall the motor head and tighten clamps.
•
Connect the vacuum power cable to the mains power
source.
•
Insert one of the supplied nozzles into the end of the
suction hose/rods.
•
Power on the vacuum at the main switch on the motor
head, using the “I” switch setting. This setting allows for
basic manual on/off function for vacuum.
•
While operating vacuum, use slow and even movements
back and forth.
•
When operation is complete switch off vacuum,
positioning switch centrally to ‘O’.
WARNING
•
Never use the vacuum without the foam intake filter.
•
The device may not be used for commercial purposes.
• Never make technical alterations to the device.
•
Only use original replacement parts and accessories
made specifically for this vacuum.
•
Only have the device repaired at authorized PondMAX
service locations.
•
Do not operate the vacuum in the rain or store in the
rain.
•
Never use the vacuum without the foam intake filter!
•
Never vacuum up flammable or toxic liquids like
gasoline, copy machine toner or other volatile
substances.
•
Never vacuum up acids.
•
Never use in the presence of explosive liquids/fumes.
•
Never vacuum up asbestos.
F O R G A R D E N S T HA T G O T H E E X T R A YARD

PMAX PV350L Instructions.indd 6 29/10/21 5:56 am
IMPORTANT
SAFEGUARDS
Please read the operating instructions and familiarise yourself with the equipment before placing it
in service. Correct and safe use of the system requires strict compliance with the safety instructions.
For safety reasons, persons less than 16 years of age or infirm persons that are not familiar with these
instructions should not use this equipment.
•
Do not operate the vacuum while standing in water or
while anyone else is in the water.
•
Before reaching into the water always unplug all
devices located in the water.
•
Only operate the device from an outlet that has been
installed in accordance with this manual.
•
Compare supply voltage (V) and supply frequency (Hz)
of your power source with the specifications pertaining
to the vacuum. This info must agree with each other.
•
Ensure that the device is protected via a residual
current protective circuit. Please consult a certified
licensed electrician if you are not sure about this.
•
For safety, plug the vacuum into an electrical outlet
with a (RCD) Residual Current Device.
•
Do not carry or pull the device by the power cable at
any time.
•
Keep the power cable plug and all other connection
points dry.
•
The device may not be operated if power cable or
motor head is defective or appears damaged.
LIMITED WARRANTY 2 YEAR
•
This product comes with a warranty against defects and
motor failure (Warranty). The benefits provided in this
•
Warranty are in addition to other rights and remedies
available to you under the Australia Consumer Law. The
Warranty is provided to the original purchaser of the
product on the following terms:
•
The Warranty is given by Aquatec Equipment Pty
Ltd trading as Aquatec Equipment: 37 Edison Circuit,
Forrestdale WA 6112; contactable by phone (08 6260
1000) or email ([email protected])
•
To make a claim under the Warranty you must return
the faulty product to the place of purchase with a valid
receipt or proof of purchase.
•
A Warranty claim must be made within 2 years of the
date of purchase.
•
If your claim complies with the above terms and the
product is not an Exhaustible Item and no Voiding
Events have occurred, we will (at our sole discretion):
- repair the product, if possible; or
-
provide a replacement product; or
-
if a replacement product is not available,
provide a refund for the purchase price paid.
•
You will bear the cost associated with claiming under
the Warranty such as the cost of transportation and
delivery of the product to and from the place of
purchase.
•
This product contains an Intake Filter, Waste Filter Bag
and Dust Bag. These items are exhaustible (Exhaustible
Items) and are not covered under the warranty.
•
The Warranty will be void if any of the following events
occur, as determined by us, at our sole discretion
(Voiding Events):
-
any tampering/removal of warranty/
identification labels or electrical components
is evident;
-
the defect has arisen due to: an accident,
incorrect or inadequate installation, misuse
or abuse of the product (including improper
maintenance and service), excessive
wear and tear, not following manufacturer’s
guidelines instructions, or the product has
been used in a manner contrary to the
purpose or suitability of the product;
-
the product has been modified without our
authority;
-
the defect is caused by power surges/spikes
brownouts.
•
Loss of livestock, damage to property or personal injury
caused by the improper use or abuse of the product
will not be covered and the manufacturer excludes all
liability for such events, to the extent permitted by law.
•
In addition to the Warranty set out above, our goods
come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to
a major failure
Please consult your retailer for quality original PondMAX replacement parts.
Visit www.pondmax.com.au for your nearest stockists. E.&O.E.
P O N D M A X . C O M . A U

PMAX PV350L Instructions.indd 1 29/10/21 5:56 am
EXPLODED VIEW
1
Motor Head
2 Intake
Filter
3
35L Container
4
Feet (X4)
5
Castor Wheels (X4)
6
Suction Hose (4.5m)
7
Wide Hard Floor Tool
8 Drain Hose (1.5m)
9
Crevice
Tool
10
Narrow Nozzle
11
Drain Cap (For Dry Use)
12
Waste Filter Bag
13
Dust Bag (X1)
14
Black Suction Rod (X2)
15
Clear Suction Rod (X2)
POWER SWITCH SETTINGS
I
Basic manual on/off function for vacuum (best for dry operation).
O Vacuum is off.
II
Automatically cycles the fill/drain system (ideal for pond operation). Vacuum has an initial
10 second delay before motor starts, 50 second suction time and 50 second emptying time. The
motor will then shut off for 50 seconds and will repeat cycle.
1
2
3
6
7
9
8
10
12
14
11
15
13
5
4

PMAX PV350L Instructions.indd 2 29/10/21 5:56 am
www.pondmax.com.au
MADE IN CHINA