PondMAX PX Series User manual

PX SERIES
HIGH FLOW FILTER PUMP
INSTRUCTION MANUAL
www.pondmax.com.au
DATE
APR 2022
MODEL
PX15000
PX25000
PMAX PX High Flow Filter Pump Instructions.indd 1PMAX PX High Flow Filter Pump Instructions.indd 1 12/5/2022 9:56 am12/5/2022 9:56 am

FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
WELCOME TO THE WORLD OF PONDMAX™.
YOU MADE THE RIGHT CHOICE INVESTING IN THIS
QUALITY PRODUCT. THANK YOU AND ENJOY.
TECHNICAL SPECIFICATIONS
DESCRIPTION PX15000 PX25000
MAXIMUM WATER FLOW (L/H) 15200 25000
MAXIMUM HEAD (m) 5.5 9.5
POWER CONSUMPTION* (W) 210 620
VOLTS (V) 220 - 240 220 - 240
IP RATING IPX8 IPX8
FREQUENCY (Hz) AC 50 50
CABLE LENGTH (m) 10 10
BALL JOINT OUTLET & STEPPED
HOSETAIL - 40mm / 32mm / 25mm Yes Yes
RECOMMENDED TUBING
SIZE (inch / mm)
1.5 / 2
38 / 50
1.5 / 2
38 / 50
PRODUCT ORDER CODE 02PX150 02PX250
* SUBJECT TO VARIATION ACCORDING TO LOAD.
PMAX PX High Flow Filter Pump Instructions.indd 2PMAX PX High Flow Filter Pump Instructions.indd 2 12/5/2022 9:56 am12/5/2022 9:56 am

PX SERIES
HIGH FLOW FILTER PUMPS
FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
• Any damage to the equipment or unmerited operation
will bring dangers to the surrounding precincts. So if
there is any damage of the equipment, it must not to
be used. The equipment should be placed out of reach
of children.
• For your own safety, disconnect from the power supply
before any maintenance of any equipment is attempted
on the tank or water body. Always unplug the pump
from the power supply when not in use
• Never pull the cable to disconnect the plug from the
power supply - Grasp the plug and pull to disconnect.
If required, have a qualified electrician install a
weatherproof power supply point near to the pond
or water-feature (within the cable length of the
appliance).
• Be sure the equipment is submerged completely in the
water. The depth should not be greater than 2m.
• Do not operate the pump if the appliance or any
components of the system, such as the power cable,
have been damaged. Check appliance for defects
regularly.
• Always use a properly grounded power supply that is
connected to an RCD with a rated residual operating
current not exceeding 30mA. As per AS/NZS
3350.2.41:1997
• To avoid an electric shock, do not attach the plug to the
power supply socket with wet hands. On installation,
the drip loop method should be used to prevent water
from traveling down the cable and onto the plug or
power supply. If the plug does get wet, do not unplug
the cable. Immediately disconnect the circuit breaker
that supplies power to the power supply point. Then
unplug and examine the plug, and power supply point,
for presence of water. If the power point has become
wet, you should consult an electrician before using the
power point again.
• Do not cut the cable as this will result in voiding your
warranty.
• Do not install or store the appliance where it will be
exposed to extreme hot or cold temperatures. Do not
use in water above 40°C.
• Care should be taken to arrange the power cable so
that it cannot be accidentally tripped over or pulled.
• Do not attempt to repair the electrical appliance
yourself. Return to an authorised service centre or place
of purchase if a fault occurs, (regular maintenance is
not considered repair and is required by user).
IMPORTANT SAFEGUARDS
Please read the operating instructions and familiarise yourself with the equipment before placing it
in service. Correct and safe use of the system requires strict compliance with the safety instructions.
For safety reasons persons less than 16 years of age or people that are not familiar with these
instructions should not use this equipment.
DESIGN HIGHLIGHTS
The PondMAX High Flow Filter Pumps have been manufactured with advanced
technology to provide you with the best quality pumps for your pond. Visit our website
to view our range of pond filtration, outdoor/ underwater lighting, water treatments and
general accessories.
• Non-submersible use at the side of the
pond, below the water level.
• Vortex impellor.
• Ideal for use in polluted water, up to a
6mm grain size.
• Ceramic bearings for continuous use.
• All the electrical parts are embedded in a
block of plastic resin.
• Energy saving split tube motor.
• Overload protection by means of a
thermal overload trip
• Simple maintenance with removable rotor
assembly
• Optimum filtration
• Dual use - both submersible or above the
water.
PMAX PX High Flow Filter Pump Instructions.indd 3PMAX PX High Flow Filter Pump Instructions.indd 3 12/5/2022 9:56 am12/5/2022 9:56 am

FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
BEFORE OPERATION
THE PUMP SHOULD NOT BE USED IF:
DURING OPERTATION:
• Check the power voltage and frequency if conformed with those on the nameplate.
• The pump must be supplied through a residual current device (RCD) having a rated
residual operating current no exceeding 30MA.
• Do not lift, lower, or carry the pump by the cable.
• Always switch off the mains before doing any maintenance or placing your hand in the
water to which this pump is connected.
• Do not add any lubricant for the appliance, do not operate the pump without water. It
will damage the pump
• It is prohibited to use in water which temperate are higher than 40°C as it remarkably
shortens the life of the pump.
• Power supply cord or other important parts are damaged in any way. The power supply
cord cannot be replaced. If the cord is damaged, the appliances should be disposed of.
• The plug or receptacle becomes wet.
• Discharge of the pump is reduced.
• Any part is broken and water leaks in.
• Anything abnormal occurs.
• Shut off the power immediately to prevent the motor from being burned out when the
motor is overloaded due to the clogging with foreign matters.
• Please consult with you local dealers or our branch office where you purchased the
unit if you cannot find the cause of the fault. Unauthorised persons are prohibited
to disassemble or assemble as it may result in the inferior of capacity or even motor
damage.
PMAX PX High Flow Filter Pump Instructions.indd 4PMAX PX High Flow Filter Pump Instructions.indd 4 12/5/2022 9:56 am12/5/2022 9:56 am

PX SERIES
HIGH FLOW FILTER PUMPS
FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
INSTALLATION
AFTER OPERATION
Installation when used inside water:
• The pump must be immersed in water completely. The minimum depth is 15cm in case of
inhaling air.
• When used in a pond or a brook, to prevent the filter (sponge) from being closed the
pump must be installed on a solid, flat surface to esnure sand and silt is not sucked up.
NOTE:
• The pump can be used indoors or outdoors. Main’s cable must not be changed or
replaced. It must not be bent or used to carry the pump. If the mains cable is damaged,
please do not use the pump.
• Power socket must be installed in a dry place. The minimum distance between it and the
pond is 1.5m.
• If freezing temperatures are predicted, lift the pump from water and restore it after
drying out the impeller chamber completely.
• If the pump is in the water for a long period of time without operation, it may rust and
floating matters may accumulate inside the pump. Rinse in clean water for a while to
remove floating matters from the pump. Restore it after drying.
PMAX PX High Flow Filter Pump Instructions.indd 5PMAX PX High Flow Filter Pump Instructions.indd 5 12/5/2022 9:56 am12/5/2022 9:56 am

FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
1. Water Inlet Cover 2. Clip 3. Water chamber 4. Impellor is suitable for particles 5. Connector 6. Hose Diameter 7. Main Housing 8. Cable Jacket 9. Handle 10. Screw
EXPLODED VIEW
IMPORTANT These accessories and attachments are recommended for use with your PondMAX product specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use the accessory or attachment for its stated purpose.
PMAX PX High Flow Filter Pump Instructions.indd 6PMAX PX High Flow Filter Pump Instructions.indd 6 12/5/2022 9:56 am12/5/2022 9:56 am

PX SERIES
HIGH FLOW FILTER PUMPS
FOR GARDENS THAT GO THE EXTRA YARDPONDMAX.COM.AU
TROUBLESHOOTING
PROBLEM REASON SOLUTION
Pump is not
working
Power is not turned on Turn on the power
Plugged in insufficiently Plug in sufficiently
Impellor binding Remove foreign matters from
impeller
Apply to wrong voltage Apply to correct voltage
The water inlet or outlet pipe is
clogged with foreign matters
Remove foreign matters from the
pipes
Pump is noisy
Impeller worn out Replace it with a new one
Water level goes down and the pump
exposed on the water source Put the pump into water
Hose is too long or clogged with
foreign matters Shorten the hose or clean up inside
There is air in the impeller chamber
(only when used outside water)
To get rid of the air, put the pump
into the water. Turn the switch to
“ON” then “OFF” intermittently
2-3 times
MAINTENANCE
The motor unit is hermetically sealed by quality resin & as such does not require any other
care. The impeller assembly rests inside an easy-open cover to allow occasional spot
checks for grime & dirt. The water chamber has an effective self-cleaning feature, but
regular maintenance will lengthen the life of the impeller & motor unit. To clean, press the
two sides of the water inlet cover, draw it and the water chamber cover from the pump.
Please note that soap or detergents are not recommended for pump maintenance because
they are bad for fishes’ health.
NOTE: Do not dispose of this unit with domestic waste. For disposal purposes, please use
the return system provided. Disable the unit beforehand by cutting off the cables.
PMAX PX High Flow Filter Pump Instructions.indd 7PMAX PX High Flow Filter Pump Instructions.indd 7 12/5/2022 9:56 am12/5/2022 9:56 am

LIMITED WARRANTY
This product comes with a warranty against defects and motor failure (Warranty). The benefits provided
in this Warranty are in addition to other rights and remedies available to you under the Australia
Consumer Law. The Warranty is provided to the original purchaser of the product on the following terms:
• The Warranty is given by Aquatec Equipment Pty Ltd trading as Aquatec Equipment.
- Tel [phone] or email [email protected]
• To make a claim under the Warranty you must return the faulty product to the place of purchase with
a valid receipt or proof of purchase.
• A Warranty claim must be made within 3 years of the date of purchase.
• If your claim complies with the above terms and the product is not an exhaustible Item and no voiding
events have occurred, we will (at our sole discretion):
- repair the product, if possible; or
- provide a replacement product; or
- if a replacement product is not available, provide a refund for the purchase price paid.
• You will bear the cost associated with claiming under the Warranty such as the cost of transportation
and delivery of the product to and from the place of purchase.
• The product contains a complete Impellor Set. These items are exhaustible (Exhaustible Items) and
are not covered under the Warranty.
• The Warranty will be void if any of the following events occur, as determined by us, at our sole
discretion (Voiding Events):
- any tampering/removal of warranty/identification labels or electrical components is evident;
- the defect has arisen due to: an accident, incorrect or inadequate installation, misuse or abuse
of the product (including improper maintenance and service), excessive wear and tear, not
following manufacturer’s guidelines/ instructions, or the product has been used in a manner
contrary to the purpose or suitability of the product;
- the product has been modified without our authority;
- the defect is caused by power surges/spikes brownouts.
• Loss of livestock, damage to property or personal injury caused by the improper use or abuse of the
product will not be covered and the manufacturer excludes all liability for such events, to the extent
permitted by law.
• In addition to the Warranty set out above, our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
Please consult your retailer for quality original PondMAX replacement parts.
Visit www.pondmax.com.au for your nearest stockists.
E.&O.E.
PONDMAX.COM.AU
PMAX PX High Flow Filter Pump Instructions.indd 8PMAX PX High Flow Filter Pump Instructions.indd 8 12/5/2022 9:56 am12/5/2022 9:56 am