Pool Frog ABOVE GROUND MINERAL SYSTEM FOR POOLS User manual

Pool FROG
ABOVE GROUND
MINERAL SYSTEM FOR POOLS
Patented Mineral Pool Sanitizer
Instruction Manual
Customer Service 800-222-0169
THE POOL FROG
®
MINERAL RESERVOIR
MUST BE REPLACED
EVERY SIX MONTHS OR
AFTER ONE POOL
SEASON WHICHEVER
IS SHORTER.

TABLE OF CONTENTS
POOL FROG®Introduction 3
Swimming Pool Tips 4
Start-up and Operation 5
Replacing POOL FROG®Mineral Reservoir 7
Replacing FROG BAM®8
Replacing POOL FROG®Bac Pac 9
Troubleshooting 10
Parts List 11
Replacing Control Dial O-Rings 12
Replacing Cap O-Ring and Knob 12
Winterizing 13
Above Ground Filter Installation 14
Above Ground Base Installation 15
Warranty 16

Part III
FROG BAM
®
Use with the POOL
FROG
®
System for an
Algae Protection
Guarantee.
Welcome to easier pool care courtesy of POOL FROG
®
. With POOL FROG
®
,your
pool water will look and feel better without a lot of work or a lot of chlorine.This
system controls bacteria using a combination of minerals and reduced chlorine
levels.There are 4 parts to the POOL FROG
®
System: The Above Ground POOL
FROG
®
Cycler, the POOL FROG
®
Mineral Reservoir, FROG BAM
®
90-day Algae
Preventative and the POOL FROG
®
Bac Pac.
Part I
POOL FROG
®
Cycler
The water treatment center that controls the flow of
water to each part of the POOL FROG
®
System.
Part II
POOL FROG
®
Mineral Reservoir
Holds the minerals and fits inside the POOL FROG®Cycler.
THE POOL FROG
®
MINERAL RESERVOIR MUST BE
REPLACED EVERY SIX MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS SHORTER.
For Above Ground Pools
up to 25,000 gallons.
POOL
FROG®
Part IV
POOL FROG
®
Bac Pac
Chlorine support fits inside
POOL FROG
®
Mineral Reservoir.
( POOL FROG
®
Mineral Reservoir sold inside POOL FROG
®
Cycler and separately for replacements.
POOL FROG
®
Bac Pac and FROG BAM
®
sold separately.)
For best results, the POOL FROG
®
Mineral
Reservoir should be used with the
chlorine Bac Pac.
P
U
L
L
O
U
T
A
N
D
R
E
A
D
Simply remove the
colored tabs on the Bac
Pac and insert into the
center of the Reservoir.
Set the dial for your size
pool, size pumpand
pump-run time per day
and adjust to maintain a
low .5 to 1 ppmchlorine
level (see manual).
Do not put anything else into the center
of the Mineral Reservoir but a Bac Pac
from King Technology or damage to the pool
or equipment could result.
If the pool has an alternate source
of chlorine (a chlorinator, floater or
hand feeding), a Flow Control Pac
must be placed in the center of the
Mineral Reservoir to ensure good
water flowthrough the minerals.
If you need a Flow Control Pac,
please call 1-800-222-0169
before you use the product.
BAM copy to come

•Make sure the pool has adequate circulation. The pool
water must completely circulate through the pump and
filter at least 1 to 2 times per day. This usually requires 8
to 12 hours. Check with your dealer for the proper circulation
time for your pool.
Swimming Pool Tips
Start-up and Yearly Maintenance
•If your fill water is high in metals, use a sequestering agent
or metal out product at start-up only before using the POOL
FROG®Mineral Reservoir. See your local dealer for details
on using these products and always follow manufacturers
directions carefully.
•Check the pool's filter gauge often and periodically clean
filter per the manufacturer's directions. A dirty filter will slow
the flow of water which could hamper proper circulation.
•After your pool is up and running
smoothly, continue to test your
water for pH, total alkalinity and
chlorine and maintain its balance
by adding any necessary
adjustment products (see your
dealer for details).
Water Balance Guidelines
pH: 7.2 — 7.8
Total Alkalinity: 60 — 120 ppm
Calcium Hardness: 150 — 400
Total Dissolved Solids: <1500
Stabilizer: 20 — 80 ppm
Free Chlorine: 0.5 — 1.0 ppm
•Before beginning with any pool care program, you must
first balance your pool water. Take a water sample to your
local pool professional or use a complete test kit that will
test for the following important elements.
1.
2.
3.
4.
5.

Start-up and Operation
•Do not add shock in or near the skimmer or into the
POOL FROG®Cycler as it could damage equipment, risk
potential explosion or discolor your pool surface.
•Add a stabilizer or conditioner to
the pool at the beginning of the
season if the stabilizer level is below
20 ppm. This will prevent chlorine
burn off. Follow manufacturer’s
directions carefully.
•Install a POOL FROG®Mineral
Reservoir into the POOL FROG®
Cycler. (Follow Directions on Page
7.)
REPLACE THE POOL FROG®
MINERAL RESERVOIR EVERY
6 MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS
SHORTER.
•When chlorine reading is down
to 1.0 ppm, which may take a few
days, insert POOL FROG®Bac
Pac. ( Follow directions on page
9.)
1.
6.
2.
3.
4.
5.
•Replace cap and run POOL
FROG®Cycler, with POOL FROG®
Mineral Reservoir inserted, for 10
minutes on Setting 10.
•For an Algae Protection
Guarantee insert FROG BAM®
into POOL FROG®Mineral
Reservoir in POOL FROG®Cycler.
(See page 8 for directions.)
•Shock the pool with chlorine to rid
the water of all contaminants before
beginning with POOL FROG®. Follow
manufacturer's directions carefully.
•THIS STEP IS VERY IMPORTANT
TO START-UP.
USE CHLORINE SHOCK ONLY.

•Set control dial by matching up the parameters of your pool on the chart below. THIS IS A
STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See #8
for directions. IMPORTANT: Pump run times less than 8 hours could result in under chlorination due
to inadequate flow through the System.
12 Hour Pump Run Time 24 Hour Pump Run Time
PUMP SIZE PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp 1/2 hp 3/4 hp 1 hp 1 1/2 hp
4.5 4 3 5 3.5 3 2.5 4
5 4.5 4 5.5 4 3.5 3 4.5
5.5 5 4.5 4 4.5 4 3.5 5
6 5.5 5 4.5 5 4.5 4 3.5
NR 6 5.5 5 5.5 5 4.5 4
7,000 (18')
9,000 (21')
12,000 (24')
15,000
20,000
Gallons
*
*
*
*
*
Diameter
8Hour Pump Run Time
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
5 4.5 4 3.5
5.5 5 4.5 4
6 5.5 5 4.5
NR 6 5.5 5
NR NR 6 5.5
Above Grd.
POOL SIZE
If using another means of chlorine support
Follow steps 1-5 on page 5 then continue below.
Test Strips
P
o
o
l
S
t
r
i
p
s
T
e
s
t
a
n
d
S
p
a
•Set dial to Setting 10.
Maintain a minimum chlorine
reading of 0.5 ppm with a
chlorine delivery device or hand
feeding.
* – Bypass installation recommended.
NR – This pump size is not recommended for this size pool.
RECOMMENDED FLOW RATE: 20-60 gpm
Start-up and Operation
7.
8.
•For the first week test the
pool water daily for free chlorine
to ensure correct dial setting.
Continue to test weekly throughout the
season.
•After each testing, adjust the dial
up by 1/2 increment if the free
chlorine reading has dropped
below 0.5 ppm or adjust down by
1/2 increment if the reading has
risen above 1.0 ppm. Continue this
process each day until the free
chlorine reading stabilizes to at
least 0.5 ppm.
•Shock pool every two weeks
or as needed to maintain water
quality. Follow label directions
on the shock treatment used.
9. •Shock pool every two weeks
or as needed to maintain water
quality. Follow label directions
on the shock treatment used.
6.
7.
•Remember to adjust dial ONLY by 1/2 setting per day in
order to prevent over chlorination which may bleach pool
surfaces.
4
4

SLOT IN POOL
FROG
MINERAL
RESERVOIR
FIN INSIDE
OF POOL
FROG CYCLER
Replacing a POOL FROG
®
Mineral Reservoir
(POOL FROG
®
Mineral Reservoirs MUST be Replaced Every Season)
ABOVE GROUND 5100 (Order #01-12-5112)
NOW FITS THE FOLLOWING CYCLERS:
POOL FROG Series 5100, 5200 or 6100
Prevail Series 5770 or 5771
7322906 05401
4.
5.
3. 6.
2.
7
•Find slot on side of
POOL FROG®Mineral
Reservoir and line up
with fin inside the
POOL FROG®Cycler.
Lower POOL FROG®
Mineral Reservoir into
POOL FROG®Cycler
until secure.
•Turn off pump and turn dial
to Setting 0. This reduces the
flow of water into the unit
when the cap is open.
•IMPORTANT: Remove and read the
information card.
Please note: complete instructions for
inserting a POOL FROG®Mineral
Reservoir, FROG BAM®and POOL
FROG®Bac Pac are included inside
the POOL FROG®Mineral Reservoir
box.
•Check the front of the box and back label of product to
make sure you have the correct POOL FROG®Mineral
Reservoir to fit your POOL FROG®Cycler.
THE POOL FROG®MINERAL RESERVOIR MUST BE
REPLACED EVERY 6 MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS SHORTER
1.
CAUTION read carefully
•USE ONLY the factory recommended replacement
POOL FROG®Mineral Reservoir, FROG BAM®and POOL
FROG®Bac Pac. DO NOT USE any other Pac or bulk
chemical tablets in the POOL FROG®Cycler. Use of any
other product could result in damage to pool equipment or
surface, unsafe pool conditions, fire or explosion. Warranty
will be void if the correct POOL FROG®Mineral Reservoir,
FROG BAM®and POOL FROG® Bac Pac are not used.
•Open cap. If using POOL
FROG® Bac Pac stand back
to avoid inhaling chlorine
fumes.
Open the box and remove the POOL
FROG®Mineral Reservoir

10.
11.
14.
12.
13.
7.
8.
9.
•Turn pump on for 90
minutes allowing FROG
BAM®to circulate through
pool.
8
90 DAY ALGAE PROTECTION
• Turn control dial on POOL
FROG
®
Cycler to Setting 10.
•Remove cap from
FROG BAM®without
removing seal.
•Insert upside down into
center of POOL FROG®
Mineral Reservoir pushing
down firmly on key inside
POOL FROG®Cycler to
puncture seal on FROG
BAM®bottle.
•Replace cap by hand only.
DO NOT OVER TIGHTEN.
Replace FROG BAM®for an Algae Protection Guarantee
If you are not replacing FROG BAM®, proceed to Step 15.
See FROG BAM®product labeling for complete directions
for use (EPA Reg. No. 53735-9).
For a preventive dose add:
• One FROG BAM
®
per 10,000 to 15,000 gallons .
• Two FROG BAM
®
per 15,000 to 30,000 gallons.
90DAYALGAEPROTECTION
90DAYALGAEPROTECTION
•Remove POOL FROG®
Cycler cap.
•To remove FROG BAM®,
turn pump off. Turn dial to
Setting 0.
•Lift FROG BAM®up and
allow any water in the
container to drain through
the POOL FROG®Cycler
before discarding in trash.
NOTE: If water shows
more than a hint of blue
inside POOL FROG®
Cycler, replace the POOL
FROG®Cycler cap, turn
dial to Setting 10 and run
the pump for one minute.
14a. If pool size requires
additional FROG BAM®,
repeat steps 7-14.
14b. When water is clear in
POOL FROG®Cycler,
proceed to step 15.

•Mark your calendar for the six month replacement of the
POOL FROG®Mineral Reservoir, 90-day replacement of
FROG BAM®and approximate replacement times for the
POOL FROG® Bac Pac. Once wetted, the time-released
mineral coating of the POOL FROG®Mineral Reservoir is
effective up to 6 consecutive months or one pool season
whichever is shorter. After that time, even if you hear the
spent media inside, it is no longer effective and must be
replaced.
19.
20.
21.
16.
17.
18.
15.
9
Colored caps
•Line up the small leg of the
POOL FROG® Bac Pac with the
small opening in the POOL
FROG® Mineral Reservoir and
the large leg with the large
opening. Lower POOL FROG®
Bac Pac into POOL FROG®
Mineral Reservoir until secure.
•To remove POOL
FROG® Bac Pac colored
caps, grab on to the lip of
one cap with a pliers and
pull up until cap releases.
Repeat the process for the
other cap.
•Holding the POOL
FROG® Bac Pac over the
POOL FROG®Mineral
Reservoir turn POOL
FROG® Bac Pac over and
shake slightly until chlorine
tablets fall into tower areas.
•Avoid sparks, open flame
or smoking when handling
the POOL FROG® Bac Pac.
Replacing POOL FROG®Bac Pac
•POOL FROG® Bac Pac
recommended to assure up
to 50% reduction in chlorine
use*. POOL FROG® Bac
Pac sold separately.
(EPA Reg. No. 53735-2)
* Compared to the minimum
EPA recommended chlorine
level of 1.0 ppm for a stabilized
swimming pool.
POOL FROG
BAC PAC
POOL FROG
MINERAL
RESERVOIR
PAC
TOWERS
PAC
TOWERS
•Replace cap by hand only.
DO NOT OVER TIGHTEN.

For more in-depth troubleshooting, go to www.kingtechnology.com
Troubleshooting
What do I do
if the water looks
cloudy?
What do I do
if the water turns
color?
1. Make sure your filtration
system is working properly (i.e.
clean filter, skimmer and pump
basket).
2. Make sure circulation time is
adequate – increase pump time
if not.
3. Make sure the pool is properly
balanced (see page 4).
4. Shock the water to eliminate
build up of any organic matter.
5. Make sure pool has a
free chlorine reading of
0.5 to 1.0 ppm.
6. Check with your dealer for
more information.
1. Metals in the fill water may
have been oxidized. Have the
pool tested. Shock the pool and
clean the filter until water clarity
returns.
2. Algae may be trying to form
– shock the pool, increase
circulation time if needed and
clean the filter.
3. Check with your dealer for
more information.
What do I do
if algae forms in
or on my pool?
1. Use a nonmetallic (polyquat)
algaecide per the directions on
the bottle and brush the sides
of the pool often.
2. Clean the filter and shock the
pool with chlorine daily until
water clarity returns.
3. If you are in an area of the
country that struggles with algae
growth, see your dealer
regarding a 90-day Algae
Protection Guarantee using
FROG BAM®. See product
hang tag for guarantee details.
4. Check with your dealer for
more information.
What do I do
if I am under
chlorinating with
the
POOL
FROG®
Bac Pac?
1. If you are unable to maintain
0.5 to 1.0 ppm, first make sure
there are chlorine tablets in the
tower areas of the POOL FROG®
Bac Pac and it is installed
properly. If a correction was
made, test the water in 24 hours.
2. If still low, turn the dial up
one setting and test the water
again in 24 hours. Continue
raising the setting by one
increment each day until the
proper reading is achieved.
3. Shock the pool if the reading
has been lower than 0.5 ppm
for more than one day.
4. Bleed air by unscrewing the
knob in the back of the POOL
FROG®Cycler while the pump
is running.
5. Increase pump time if
possible.
6. Contact your dealer to have
your back pressure tested to
ensure it is between 3 & 8 psi.
7. Contact King Technology’s
Customer Service Department at
800-222-0169.
What do I do
if I am over
chlorinating with
the
POOL FROG®
Bac Pac?
1. If the chlorine reading is over
3.0 ppm, remove the POOL
FROG® Bac Pac from the POOL
FROG®Mineral Reservoir and test
the water daily until the reading is
down to 1.0 ppm.
2. Reinsert the POOL FROG® Bac
Pac, lower the dial one setting and
test the water again in 24 hours.
If the reading has risen, lower
the dial one setting again.
Continue this process until
proper reading is achieved.
3. If over-chlorinating at the
lowest possible setting, consider
decreasing the circulation time.
Depending on your pump size,
Problem Remedy
1.
2.
3.
4.
5.
10
you may be circulating the water
more than is necessary which
results in more chlorine than is
necessary.
4. Contact King Technology’s
Customer Service Department
at 800-222-0169.

CYCLER DIAGRAM/PARTS LIST •Model 6100 or 6500
REF. # PART NO. DESCRIPTION QTY. REQ.
1 & 2 01-22-1418 Cap w/O-Ring 1
2 01-22-1920 Cap O-Ring 1
3 N/A Body 1
4 01-22-9480 Pressure Relief Valve 1
5, 6, 7 01-22-1448 Control Dial
with O-Rings 1
6 01-22-1450 Control Dial O-Ring Set 1
7 N/A Control Dial Locking Pin 1
8 & 9 01-22-9941 Knob with O-Ring 2
10 01-22-9970 Silicone Lubricant 1
11 01-22-1710 Nipple Kit 1
12 01-22-1480 Mounting Base 1
Parts List Model 6100/6500
11
C
OP
Y
C
OP
Y
C
O
PY
C
OP
Y
OT
HE
RC
OP
Y?
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
10
11
1
2
4
8 & 9
5
7
6
8
9
12

POOL FROG®Cycler Maintenance
•Turn control dial back and
forth as you pull it out of the
housing.
•In the back of the POOL
FROG®Cycler depress center
of locking pin with a finger and
pull pin out of dial.
•Replace both o-rings. Apply
silicone lubricant that came with
your POOL FROG®Cycler on
o-rings.
•Carefully insert control dial
back into housing.
•Replace locking pin by
pushing it through the slots on
the dial until it locks into place.
C
OP
Y
C
OP
Y
C
O
PY
C
OP
Y
OT
HE
RC
OP
Y?
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
Replacing Cap O-Ring
•Hold cap in front of you
upside down with the o-ring
groove facing up. Place one
end of o-ring into cap groove
at the point closest to you.
Hold o-ring down with the
thumb and forefinger of one
hand.
•Take hold of the far end of
the o-ring with the thumb and
index finger of the other hand.
Roll o-ring slightly back
towards you as you stretch
the o-ring into the remainder
of the cap groove.
•Lubricate o-ring often with
silicone lubricant that came
with your POOL FROG®
Cycler. DO NOT USE
petroleum based lubricants.
Replacing knob
C
OP
Y
C
OP
Y
C
O
PY
C
OP
Y
x
xxx
x
S
L
I
CO
N
E
L
U
B
R
I
C
A
N
T
• T o replace, simply unscrew
old knob and replace with the
new one.
Back of
POOL
FROG
®
Cycler
Front of
POOL
FROG
®
Cycler
1.
2.
3.
4.
5.
1.
2.
3.
12
Replacing the Control Dial O-Rings
Center of locking pin

Winterizing
•Turn pump off and turn
dial to Setting 0.
•Remove cap.
•Unscrew knob from the
front of POOL FROG®
Cycler. Allow all water to
drain.
•Remove the POOL FROG®
Mineral Reservoir and discard
in trash. Even if you hear spent
minerals inside, it is no longer
effective.
•If POOL FROG® Bac Pac still
contains chlorine wrap in plastic
bag and store in shed or garage
away from children and pets.
Make sure POOL FROG® Bac
Pac is away from open flame or
anything metal.
1.
2.
3.
4.
5.
6.
13
•Replace the cap and knob
loosely.

Above Ground Filter Installation
Apply tape to each threaded
end of nipple.
Screw one end of nipple
into the filter return.
Screw either side of
POOL FROG®Cycler on
to open nipple end until
upright and secure.
Tighten turning
1 to 2 revolutions with wrench.
DO NOT OVER TIGHTEN.
Tighten turning
1 to 2 revolutions
with wrench.
DO NOT
OVER TIGHTEN.
Bi-flow valve
design allows
water flow in
either
direction.
HOSE ADAPTER
4.
5.
6.
1.
2.
3.
7.
MATERIALS NEEDED
One
Hose
Clamp
Corrosion Resistant
Check Valve
RECOMMENDED
INCLUDED WITH
POOL FROG® CYCLER
14
Apply tape to
threaded end of hose
adapter.
Screw adapter into the other
side of POOL FROG®Cycler.
Attach return section of hose
to the adapter with clamp.
Tighten clamp with
screwdriver.
TOOLS NEEDED
Screwdriver
If using a POOL FROG® Bac
Pac, installing a corrosion
resistant check valve is
recommended.
Tape
One Hose Adapter
1 1/2" X1 1/2" X1 1/4"
One 6" X1 1/2" TBE
PVC Nipple
One Section of
1 1/2" Flex Hose
(provided with filter)
Pipe Wrench

Apply tape to the threaded
end of both hose adapters.
Screw adapters into each end of POOL FROG®
Cycler. Tighten turning 1 to 2 revolutions with wrench.
DO NOT OVER TIGHTEN.
Attach the filter section of
flex hose to one hose
adapter and the return
section of flex hose to the
other hose adapter with
clamps and tighten with
screwdriver.
Above Ground, Base Installation
HOSE
CLAMP
HOSE
ADAPTER
HOSE
CLAMP
HOSE
ADAPTER
TO POOL
1 1/2" OR 1 1/4"
FLEX HOSE
1 1/2" X1 1/2" X1 1/4"
HOSE ADAPTER
HOSE
CLAMP
FILTER &
PUMP
The POOL FROG®Cycler should always be
installed between the filter and pool (or between
heater and pool if applicable).
TO POOL
PUMP
FILTER
Bi-flow valve design allows
water flow in either direction.
1. 2.
3.
4. 5.
MATERIALS NEEDED
Two
Hose
Clamps
Corrosive Resistant
Check Valve
RECOMMENDED
OPTION
1 1/2" Male Adaptor
(slip XMPT)
When installing with
hard PVC pipe, use a
male adapter on the
inside port threads.
#10 X1 1/4" Phillips
Pan Head Screws with
Washers
15
TOOLS NEEDED
If using a POOL FROG® Bac Pac installing a corrosion resistant
check valve is recommended.
Tape
Two Hose Adapters
1 1/2" X1 1/2" X1 1/4"
Two Sections
of 1 1/2" Flex Hose
(one provided with filter)
For better stability, POOL
FROG®Cycler may be
mounted on a base using
Phillips pan head screws. One
in front and two in back.
Screwdriver
Pipe Wrench

Manufactured by: KING TECHNOLOGY, INC.
530 11th Avenue South, Hopkins, MN 55343 U.S.A.
952-933-6118 •800-222-0169 •FAX [phone] www.kingtechnology.com
Made in U.S.A.
Covered by one or more of the following U.S. Patent Numbers: 4,662,387;
5,076,315; 5,218,983; 6,190,547; 6,210,566; 6,217,892; 6,383,507; 6,551,609;
6,652,871; 6,544,415 and other U.S. and Foreign Patents Pending.
20-48-0151E
553100543R2
King Technology, Inc. warrants to the original purchaser this unit
will be free from any defects in workmanship and/or material, for
a period of two (2) years from the date of original purchase. This
warranty covers body, cap and control dial, but specifically excludes
o-rings. King Technology at its option may replace any defective
parts or the entire unit without charge after it is determined what
is needed to correct any deficiency. Replacement parts with the
exception of o-rings are warranted for the remainder of the original
warranty. To extend the limited warranty from two years to ten years,
simply complete the warranty card that came with your unit and
return it to King Technology within 30 days of purchase and
installation.
1. To obtain warranty service, you must deliver the unit to King
Technology or its nearest authorized dealer. Shipping expenses
are the purchaser's responsibility. The name of the nearest authorized
dealer can be obtained by writing or calling King Technology at the
address and telephone number provided below. Proof of purchase
is required when requesting warranty service. Purchaser must
present the sales receipt or other documentation verifying proof of
purchase.
2. This warranty does not cover defects caused by: Modification,
alteration, repair or service of the unit contrary to the accompanying
instructions; physical abuse to or misuse of the product or operation
or installation in a manner contrary to the accompanying instructions.
This warranty also excludes all costs arising from the installation,
adjustment, removal or replacement of defective units or parts. This
warranty also excludes any and all claims arising out of the chemicals
used in the product or their characteristics.
3. CAUTION - Read carefully – Failure to follow these instructions
will void the warranty. Do not add shock in or near skimmer.
A. This unit is not designed for shock treatment of pools. See
your pool dealer or distributor for further information concerning
shock treatments.
16
POOL FROG®Cycler Two-Year Limited Warranty
B. Control dial settings in excess of the recommended setting
levels for trichlor can result in excess sanitizers being discharged
into the pool. This can result in bleaching or discoloration of
areas around the pool inlet or in some cases bleaching or
discoloration of the entire pool liner or paint.
C. Excess trichlor in the pool can create health hazards to
bathers. Consult each chemical manufacturer's warnings and
cautions for specifics.
D. Misuse or failure to use the proper POOL FROG®Mineral
Reservoir and POOL FROG®Bac Pac may cause damage to
equipment or personal injury. This warranty will be null and
void, if this unit is not used with the recommended POOL FROG®
Mineral Reservoir and POOL FROG®Bac Pac.
4. This warranty is the exclusive warranty for the POOL FROG®
Cycler. This warranty is not transferable. KING TECHNOLOGY
MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER
CONCERNING THE POOL FROG®CYCLER. Any express warranty
not provided herein, and any remedy for breach of contract but which
for this provision might arise by implication or operation of law is
hereby excluded and disclaimed. THE EXCLUSIVE REMEDY FOR
ANY CUSTOMER IS THE REPAIR OR REPLACEMENT OF THE
UNIT, AND THE RECOVERY OF DAMAGES WILL NOT EXCEED
THE PURCHASE PRICE OF THE UNIT. IN NO EVENT WILL KING
TECHNOLOGY BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL,
SPECIAL OR PUNITIVE DAMAGES FROM ANY CAUSE.
5. Under no circumstance shall King Technology be liable to purchaser
or any other person for any damage or loss incurred because of any
chemicals used in the product or their physical characteristics, or
interruption of service of the product, or any resulting special,
incidental or consequential damages or losses. Some states do not
allow the exclusion or limitation of incidental consequential damages,
so the above limitation or exclusion may not apply to you.