poolstar POOLEX ARTICLINE FI User manual

INSTALLATION AND OPERATION MANUAL
for your heat pump
www.poolstar.fr
ARTICLINE FI

2
AcknowledgementsWarning
This heat pump contains R32 ammable refrigerant.
Prior approval must be obtained before any procedure is performed on the refrigerant circuit.
To ensure user safety, the following precautions must be followed before any procedure is per-
formed on the refrigerant circuit.
1. Work procedure
All work must be carried out in accordance with strict guidelines in order to minimise the risk of gas or ammable
vapour escaping during the execution of the work.
2. General workplace conditions
All persons present in the work area must be informed as to the nature of the work being carried out. Avoid performing
work in conned spaces. The area surrounding the work space must be cordoned o and particular attention must be
paid to nearby sources of heat or ames.
3. Monitoring the presence of refrigerant
The area must be monitored for the presence of refrigerant, using an appropriate detector, before and after any
work takes place in order to ensure that no potentially ammable gas has escaped. Ensure the equipment used for
detecting leaks is suitable for ammable refrigerants, i.e., does not generate sparks, the device is properly sealed or
equipped with internal safety measures.
4. Fire extinguishers
If hot work is being performed on the refrigeration system, or any related system, appropriate re extinguishing
equipment must be available. Install a dry powder or CO2 re extinguisher near the work area.
5. No sources of heat, open ames or sparks
The presence of heat sources, open ames or sparks in close proximity to one or more parts/pipework containing or
having contained ammable refrigerant is strictly prohibited. All sources of sparks, including smoking, must be located
suciently far away from the site of installation, repairs, removal and disposal, during which ammable refrigerant
could escape into the surrounding environment. Before beginning work, the environment surrounding the equipment
must be veried to ensure there is no source of ignition. “No smoking” signs must be displayed.
6. Ventilated area
Ensure that the workplace is open to the air, or properly ventilated, before performing any work on the system or
carrying out hot work. Sucient ventilation must be maintained throughout the period of work.
7. Inspection of refrigeration equipment
When electrical components are replaced, they must be suitable for their intended use and meet the relevant speci-
cations. Replacements must be genuine or OEM parts. If in doubt, contact the manufacturer’s customer support team.
Inspections must be performed on installations using ammable refrigerants:
– Refrigerant charge must be appropriate for the size of the space in which the refrigeration system is installed..
– The ventilation system and air vents must function correctly and must not be obstructed.
– If an indirect refrigeration system is being used, the secondary circuit must also be inspected.
– Equipment markings must be clearly visible and legible. Illegible signs and markings must be corrected.
– Refrigerant pipework and components must be installed in locations with no risk of exposure to substances capable
of corroding components containing refrigerant uid.
8. Inspection of electrical appliances
Repairs and maintenance performed on electrical appliances must include preliminary safety tests and inspection
of components. In the event a fault is detected which is capable of compromising safety, electrical power must be
disconnected from the circuit until the problem is resolved.
Preliminary safety tests must include the following:
• Ensuring the condensers are fully discharged: this must performed in a safe manner to avoid the risk of ignition;
• Ensuring that no wires or electrical components are exposed at the time of charging, recovery, or purging the system
of refrigerant gas.
• Ground continuity test.

3
Dear customer,
Thank you for your purchase and your trust in our products.
Our products are the result of years of research in the design and manufacture of heat
pumps for pools. Our goal is to deliver high-quality products with exceptional performance.
We took great care to put together this manual so you can get the most out of your Poolex
heat pump
Acknowledgements

4
PLEASE READ CAREFULLY
These installation instructions form an integral part of the product.
They must be provided to the installer and kept in a safe place by the user.
If you lose this manual, please visit our website:
www.poolex.fr
The indications and warnings contained in this manual should be carefully read and understood as they
provide important information regarding the safe handling and operation of the heat pump. Keep this
manual handy for future reference.
Installation must be performed by a qualied professional in accordance with regulations in force and
the manufacturer's instructions. Errors made during installation can cause physical injuries to people and
animals, as well as mechanical damage for which the manufacturer shall not be held liable.
After unpacking the heat pump, please check the contents for any signs of damage.
Before plugging in the heat pump, ensure that the instructions provided in this manual are compatible
with the actual installation conditions and do no exceed the maximum authorised limits for the product in
question.
In the event of a defect and/or malfunction of the heat pump, electrical power must be shut o󰀨 and
no attempts to repair the fault should be made.
Repairs must be carried out by an authorised technician using original spare parts. Non-compliance with
the aforementioned clauses can negatively impact the safe operation of the heat pump.
In order to guarantee the e󰀩ciency and ensure the proper functioning of the heat pump, it must be regularly
maintained in accordance with the instructions provided.
In the event the heat pump is sold or transferred to a third party, please ensure that all technical documen-
tation is given to the new owner alongside the equipment.
This heat pump has been designed to only heat the water of a swimming pool. Any other use is considered
inappropriate, incorrect and potentially dangerous.
! !
All contractual and extra-contractual liability on the part of the manufacturer / distributor shall be considered
null and void in the event of damage caused by errors in installation or operation, or due to non-compliance
with the instructions provided in this manual, or the standards in force for the installation of equipment
discussed in this document.

5
Contents
1. General ....................................................................................................................................................................... 6
1.1 General terms and conditions of delivery ............................................................................................................... 6
1.2 Safety instructions .................................................................................................................................................. 6
1.3 Water treatment ...................................................................................................................................................... 7
2. Description................................................................................................................................................................. 8
2.1 Package contents ................................................................................................................................................... 8
2.2 General characteristics ........................................................................................................................................... 8
2.3 Technical characteristics......................................................................................................................................... 9
2.4 Product dimensions .............................................................................................................................................. 10
2.5 Exploded view........................................................................................................................................................11
3. Installation................................................................................................................................................................ 12
3.1 Prerequisite........................................................................................................................................................... 12
3.2 Location ................................................................................................................................................................ 12
3.3 Installation diagram.............................................................................................................................................. 13
3.4 Connecting the condensation draining kit............................................................................................................ 13
3.5 Installing the equipment on silencing supports ..................................................................................................... 13
3.6 Hydraulic connection ............................................................................................................................................ 14
3.7 Electrical installation ............................................................................................................................................. 16
3.8 Electrical connections ........................................................................................................................................... 17
4. Use............................................................................................................................................................................ 18
4.1 Wired control box.................................................................................................................................................. 18
4.2 Operating modes .................................................................................................................................................. 19
4.3 Smart LED technology.......................................................................................................................................... 19
4.4 Heat pump operating mode selector..................................................................................................................... 20
4.5 Temperature set point settings.............................................................................................................................. 20
4.6 Clock settings ....................................................................................................................................................... 21
4.7 On / O󰀨 synchronization adjustment..................................................................................................................... 22
4.8 Lock / Unlock ........................................................................................................................................................ 23
4.9 WiFi connection .................................................................................................................................................... 23
4.10 Status values control ............................................................................................................................................ 24
4.11 User parameters ................................................................................................................................................... 25
4.12 Technical parameters............................................................................................................................................ 26
5. Operation.................................................................................................................................................................. 28
5.1 Operation .............................................................................................................................................................. 28
5.2 Servo-control of circulating pump ......................................................................................................................... 28
5.3 Using the pressure gauge..................................................................................................................................... 29
5.4 Antifreeze protection............................................................................................................................................. 29
6. Maintenance and servicing..................................................................................................................................... 30
6.1 Maintenance and servicing ................................................................................................................................... 30
6.2 Winter storage ...................................................................................................................................................... 30
7. Repairs ..................................................................................................................................................................... 31
7.1 Breakdown and faults ........................................................................................................................................... 31
7.2 List of faults........................................................................................................................................................... 31
8. Warranty ................................................................................................................................................................... 33
8.1 General terms and conditions of delivery ............................................................................................................. 33
9. Appendices .............................................................................................................................................................. 34
9.1 Wiring diagrams.................................................................................................................................................... 34

6
All products and packaging, even those delivered carriage paid, travel at the risk of the recipient.
Persons responsible for accepting delivery of the device must perform a visual inspection to make a note of
any damage that may have occurred during transportation (refrigeration circuit, casing, electric box, frame).
Any damage occurring during transportation must be noted by the recipient on the delivery receipt of the
carrier, and conrmed by registered post sent to the carrier within 48 hours.
The device must be stored and transported upright at all times, on a pallet, and in its original packaging. If
the device has been transported in a horizontal position, please wait at least 24 hours prior to connecting it.
Installation and maintenance
Only a qualied person may undertake installation, start-up, servicing and repairs, in compliance with
current standards.
Before operating or undertaking any work on the devoce (installation, start-up, use, servicing), the person
responsible must be aware of all the instructions in the heat pump’s installation manual as well as the
technical specications.
Under no circumstances install the equipment close to a source of heat, combustible materials or a build-
ing’s air intake.
If installation is not in a location with restricted access, a heat pump protective grille must be tted.
To avoid severe burns, do not walk on pipework during installation, repairs or maintenance.
To avoid severe burns, prior to any work on the refrigerant system, turn o󰀨 the heat pump and wait several
minutes before placing temperature and pressure sensors.
Check the refrigerant level when servicing the heat pump.
Check that the high and low pressure switches are correctly connected to the refrigerant system and that
they turn o󰀨 the electrical circuit if tripped during the equipment’s annual leakage inspection.
Check that there is no trace of corrosion or oil stains around the refrigerant components.
1.1 General terms and conditions of delivery
1.2 Safety instructions
WARNING: Please read carefully all safety instructions before using the device.
As the instructions noted in this document are essential to your safety, please respect them
carefully.
1. General

7
1.3 Water treatment
Poolex heat pumps for swimming pools can be used with all types of water treatment systems.
Nevertheless, it is essential that the treatment system (chlorine, pH, bromine and/or salt chlorinator meter-
ing pumps) is installed after the heat pump in the hydraulic circuit.
To avoid any deterioration to the heat pump, the water’s pH must be maintained between 6.9 and
8.0.
1. General
When in use
Do not touch the vent during operation due to the risk of serious injury.
Do not leave the heat pump within reach of children due to the risk of injury caused by the heat exchanger
ns.
Never start the equipment if there is no water in the pool or if the circulating pump is stopped.
Check the ow rate of the water every month and clean the lter if necessary.
When cleaning
Switch o󰀨 the power supply to the device.
Close the water inlet and outlet valves.
Do not place anything in the openings of the water or air inlets/outlets.
Do not spray the appliance with excessive amounts of water.
During repairs
Carry out work on the refrigerant system in accordance with current safety regulations.
Brazing should be performed by a qualied welder.
When replacing a defective refrigerant component, use only parts certied by our technical department.
When replacing pipework, only copper pipes conforming to Standard NF EN12735-1 may be used for
repairs.
When pressure-testing to detect leaks:
Never use oxygen or dry air as there is a risk of re or explosion.
Use dehydrated nitrogen or a mixture of nitrogen and refrigerant.
The low and high side test pressure must not exceed 42 bar.

8
2.1 Package contents
2.2 General characteristics
✔ Poolex Articline Fi heat pump
✔ 2 hydraulic inlet/outlet connectors 1"1/2 threaded and union D50
✔ Extension cable (10 m) for remote control panel
✔ This installation and operation manual
✔ Condensate discharge pipe
✔ Winter cover
✔ 4 anti-vibration pads (fastenings not supplied)
A Poolex heat pump has the following features:
High performance with up to 80% energy savings compared to a conventional heating system.
Clean, e󰀩cient and environmentally friendly R32 refrigerant.
Reliable high output leading brand compressor.
Wide hydrophilic aluminum evaporator for use at low temperatures.
User-friendly intuitive remote control.
Designed to be silent.
LEDs for quick status indication
Dual antifreeze system to avoid frost damage:
- Revolutionary exchanger with patented antifreeze system,
- A smart monitoring system to preserve the pipework and liner without emptying the pool in winter.
CE certication and complies with the RoHS European directive.
2. Description

9
2.3 Technical characteristics
2. Description
The technical specications of our heat pumps are provided for information purposes only. We reserve the right to make changes without prior
notice.
1 Ambiant air temperature
2Initial water temperature
3
Noise level at 1 m and 10 m in accordance with international standards EN ISO 3741 and EN ISO 354 and according to the selected operating mode
4Calculated for an in-ground private swimming pool covered with a bubble cover in Metropolitan France
Testing
conditions
Poolex Articline Fi
155
Air (1) 26°C
Water (2) 26°C
Heating capacity (kW) 20.01~3.95
Consumption (kW) 3.38~0.286
COP (Coe. of performance) 13.81~5.92
Air (1) 15°C
Water (2) 26°C
Heating capacity (kW) 15.53~2.95
Consumption (kW) 3.12~0.439
COP (Coe. of performance) 6.72~4.97
Air (1) -25°C
Water (2) 26°C
Heating capacity (kW) 6.95~2.35
Consumption (kW) 3.05~0.505
COP (Coe. of performance) 4.65~2.28
Air (1) 35°C
Water (2) 27°C
Cooling capacity (kW) 10.01~3.39
Consumption (kW) 2.95~0.646
EER (Coe. of performance) 5.25~3.39
Max. power (kW) 3.5
Max. current (A) 15.53
Power supply 220-240V 50 / 60 Hz
Protection IPX4
Heating temperature range 15°C~40°C
Cooling temperature range 8°C~28°C
Operation temperature range -25°C~43°C
Unit dimensions L x W x H (mm) 1116 x 434 x 710
Unit weight (kg) 77
Sound pressure level à 1m (dBA) (3) 39~50
Sound pressure level à 10m (dBA) (3) 19~30
Hydraulic connections (mm) PVC 50 mm
Heat exchanger PVC tank and tianium heating coil
Max water ow rate (m³/h) 6.4
Compressor make GMCC
Compressor type Twin Rotary
Refrigerant R32
Refrigerant volume 1350 g
Load loss (mCE) 1.1
Max. pool volume (m³) (4) 80
Remote control Wired digital display control
Mode Eco Booster & Eco Silence (Inverter) / Heating / Cooling / Auto

10
2.4 Product dimensions
2. Description
Dimensions in mm

11
2.5 Exploded view
2. Description
1. Base
2. Front panel 1
3. Left panel
4. Separation panel
5. Fan motor mount
6. Cover
7. Right side panel
8. Right panel
9. Electrical box cover
10. Rear panel
11. Front panel 2
12. Maintenance panel
13. Connection box cover
14. Rear grid
15. Electrical elements
16. Evaporator
17. Titanium heat exchanger
18. EVI
19. Fan motor
20. Ventilator blades
21. Compressor
22. 4-way valves
23. EEV 1
24. EEV 2
25. Pressure gauge
26. LED
27. Connection box
19
3
20
11
16
2
5
17
12
26 7 21 1 18
13
24
4
10
25
142369
15
22
8
27

12
Equipment necessary for the installation of your heat pump:
✔ Power supply cable suitable for the unit’s power requirements.
✔ A By-Pass kit and an assembly of PVC tubing suitable for your installation.
✔ Stripper, PVC adhesive and sandpaper.
✔ 4 wall plugs and 4 expansion screws suitable to attach the unit to your support.
We recommend that you connect the unit to your installation by means of exible PVC pipes in order to
reduce the transmission of vibrations.
Suitable fastening studs may be used to raise the unit.
3.1 Prerequisite
3.2 Location
Please respect the following rules when choosing the heat pump’s installation location
1. The location must be easily accessible for optimal operation and maintenance.
2. The device must be installed on the ground, ideally on a level concrete slab. Ensure that the ground is
su󰀩ciently stable and it can support the weight of the device.
3. A water drainage device must be provided close to the unit in order to protect the area where it is installed.
4. If necessary, the unit may be raised by using suitable mounting pads designed to support its weight.
5. Check that there is enough air ow, that the air exhaust is not directed towards the windows of neighbour-
ing buildings, and that exhaust air cannot return to the intake. In addition, ensure that there is enough
space around the device to perform servicing and maintenance.
6. The device must not be installed in locations susceptible of being exposed to oil, ammable gas, corrosive
agents, sulphur compounds, or near high frequency devices.
7. Do not install the device near to roads or footpaths to avoid mud splattering.
8. To avoid disturbing neighbours, make sure to install the device facing away from areas sensitive to noise.
9. Keep out of the reach of children insofar as possible.
3. Installation
WARNING: Installation must be performed by a qualied professional.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.
Do not place anything within 2.5m of the front of the heat pump.
Leave a free space of 50 cm all around the heat pump.
Do not place any obstacles on top or in front of the device!
2500
Dimensions in mm

13
3.3 Installation diagram
3.4 Connecting the condensation draining kit
3.5 Installing the equipment on silencing supports
While operating, the heat pump is subject to a condensation phenomenom. This will result in a more or less
large run-o󰀨 of water, depending on the degree of humidity. To channel this ow, we recommend that you
install the condensation drainage kit.
How do you install the condensation drainage kit?
Install the heat pump, raising it at least 10 cm with solid water-resistant pads, then connect the drainage
pipe to the opening located under the pump.
In order to minimise the noise pollution associated with heat pump vibrations, it can be positioned on
vibration absorbing pads.
To do this, you simply have to position a pad between each of the unit’s feet and its support, and then x
the heat pump to the support with suitable screws.
3. Installation
Valves 1, 2 and 3: Bypass valves
Valves 4 and 5: Regulating valves
(Recommended for facilitating adjustments close to the machine)
Half-open valve Open valve
Caption
Heat pump
Water outlet
Water inlet
Elevating studs
Drain plug Condensation
drainage
Valve 4
Valve 5
Valve 3 Valve 2
Circulation
pump
Filtration
Valve 1
Automatic treatment system
(electrolyseur, dosing pump)
TO THE POOL
FROM THE POOL
4-way valve

14
Hydraulic connection with the By-Pass kit
Step 1: Take the necessary measurements to cut your pipes.
Step 2: Make a straight perpendicular cut through the PVC pipes with a saw.
Step 3: Assemble your hydraulic circuit without connecting it in order to check that it perfectly ts your
installation, then dismantle the pipes to be connected.
Step 4: Chamfer the ends of the cut pipes with sandpaper.
Step 5: Apply stripper to the ends of the pipes to be connected.
Step 6: Apply glue in the same place.
Step 7: Assemble the pipes.
Step 8: Clean o󰀨 any glue remaining on the PVC.
Step 9: Leave to dry for at least 2 hours before putting the hydraulic circuit into water.
3.6 Hydraulic connections
WARNING: Installation must be performed by a qualied professional.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.
WARNING: Do not run any water through the hydraulic circuit for at least 2 hours following
assembly.
By-Pass assembly
The heat pump must be connected to the pool by
means of a By-Pass assembly.
A By-Pass is an assembly consisting of 3 valves that
regulate the ow circulating in the heat pump.
During maintenance operations, the By-Pass permits
the heat pump to be isolated from the system without
interrupting your installation.
TOWARDS THE POOL
Open valve
Half-open valve
FROM THE POOL
3. Installation

15
By-Pass assembly for several heat pumps
By-Pass assembly for one heat pump
The lter located upstream of the heat pump must be regularly cleared so that the water in the system is
clean, thus avoiding the operational problems associated with dirt or clogging in the lter.
3. Installation
Half-open valve
Half-open valve
Open valve
Open valve
Caption
Caption
TO THE POOL
Filtration + Pump
Filtration + Pump
Automatic treatment
system
Automatic treatment
system
TO THE POOL
FROM THE POOL
POOL
POOL
FROM THE POOL

16
3. Installation
To function safely and maintain the integrity of your electrical system, the unit must be connected to a
general electricity supply in accordance with the following regulations:
• Upstream, the general electricity supply must be protected by a 30 mA di󰀨erential switch.
• The heat pump must be connected to a suitable D-curve circuit breaker (see table below) in accord-
ance with current standards and regulations in the country where the system is installed.
• The electricity supply cable must be adapted to match the unit’s rated power and the length of wiring
required by the installation (see table below). The cable must be suitable for outdoor use.
• For a three-phase system, it is essential to connect the phases in the correct sequence.
If the phases are inverted, the heat pump’s compressor will not work.
• In places open to the public, it is mandatory to install an emergency stop button close to the heat
pump.
Models Power supply Maximum
current
Cable
diameter
Thermal-magnetic
(D curve) protection
Articline Fi Single phase
230V/~50Hz 15.5 A RO2V 3x4 mm² 20 A
1Cable cross-section suitable for max. length 10 metres. For longer than 10 metres, consult an electrician.
3.7 Electrical installation
WARNING: Installation must be performed by a qualied professional.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.

17
Please comply with the following instructions to electrically connect the heat pump.
Step 1: Dismount the electrical side panel with a screwdriver to access the electrical terminal block.
Step 2: Insert the cable into the heat pump unit by passing it through the opening provided for that purpose.
Step 3: Connect the power supply cable to the terminal block in accordance with the diagram below
Step 4: Carefully close the heat pump panel.
Servo-control of circulating pump
Depending on the type of installation, you can also connect a circulating pump to terminals P1 and P2 so
that this operates in tandem with the heat pump.
3. Installation
3.8 Electrical connections
WARNING: The heat pump’s power supply MUST be disconnected before any operation.
WARNING: Servo-control of a pump whose power exceeds 5A (1000W) requires the use of a
power relay.
L N P1P2
Connecter à l’alimentation
230V / 50Hz
Connecter à la
pompe à filtration
ou un relais de puissance
PHASE NEUTRE TERRE PHASE NEUTRE
Single phase model
Connect to power supply
230V / 50 Hz
PHASE NEUTRAL NEUTRALEARTH PHASE
Connect to a
ltration pump
or a power relay

18
SET IN NO ROOM VALUE OUT
1
2
ON
OFF
TEMP
HUM
h
MI N
%
F
C C
AUTO
FAN
h
MI N
%
F
4. Use
4.1 Wired remote control
Before setting your set temperature, familiarise yourself with the di󰀨erent symbols represented by the
remote control:
Eco cooling mode
+nE
+nE
+H1
+H1
+l0
+l0
Compressor
Ventilator
Inlet water temperature
Settings menu
Temperature unit
Clock / Timer
Clock setting
Locking the pad
On/O󰀨 Timer setting
Eco heating mode
Auto mode
Boost heating mode
Boost cooling mode
Eco Silent heating mode
Eco Silent cooling mode
Defrost
Temperature setting
Set temperature and water inlet
(displayed right)
Before use, ensure that the ltration pump is working and that water is circulating through the
heat pump.
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
Connected heater

19
4. Use 4. Use
4.2 Operating modes
4.3 LED smart technology
Prior to setting your required temperature, you must rst select an operating mode for your heat pump.
The Articline proposes 7 operating modes combining:
• Heating mode or cooling mode,
• Eco or Boost or Silent modes.
• Automatic mode can only be used in Eco mode.
Heating mode:
Choose this operating mode so that the heat pump heats up your pool.
Cooling mode:
Choose this operating mode so that the heat pump cools down your pool in Inverter mode.
Automatic mode:
Choose this mode so that the heat pump smartly chooses the operating mode according to the
requirements to reach set temperature.
Eco mode:
Choose this mode so that the heat pump operates in smart mode.
Silent mode:
Choose this mode so that the heat pump operates in silent mode.
Boost Mode:
Choose this mode so that the heat pump operates in full power mode.
+nE
+H1
+l0
The ambient LEDs integrated into the front of your heat pump provide you with instant information on the
operating status of your heat pump.
Blue: Your pool is being heated.
Green: Your heat pump has reached its target temperature.
Red: Action required.
If necessary, this function can be deactivated. See § 4.11, page 25.
Set L6 to 0 to disable LEDs.

20
4. Use
When the incoming water temperature is less than or equal to the required temperature (setpoint temper-
ature - 1°C), the heat pump will switch to heating mode. The heater will stop when the temperature of the
incoming water is greater than or equal to the required temperature (setpoint temperature + 1°C).
WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart
after 10 minutes.
Good to know
4.4 Selecting the operating mode
4.5 Temperature set point setting
WARNING: Before starting, ensure that the ltration pump is operating correctly.
Press on
SET IN NO ROOM VALUE OUT
1
2
ON
OFF
TEMP
HUM
h
MIN
%
F
AUTOFAN
h
MIN
%
F
to switch operating mode. The di󰀨erent modes are displayed in the following order:
Cooling mode
Silent
Cooling mode
Boost
Cooling mode
Eco
+LO
+H1
+nE
+nE
+H1
+L0
Heating mode
Eco
Heating mode
Boost
Heating mode
Silent
Automatic mode
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
SET
IN
1
2
ON
OFF
C
FAN
Once de the control panel unlocked, press on
SET IN NO ROOM VALUE OUT
1
2
ON
OFF
TEMP
HUM
h
MI N
%
F
AUTOFAN
h
MI N
%
F
and
SET IN NO ROOM VALUE OUT
1
2
ON
OFF
TEMP
HUM
h
MI N
%
F
AUTOFAN
h
MI N
%
F
to increase of decrease the set temperature.
Press on
SET IN NO ROOM VALUE OUT
1
2
ON
OFF
TEMP
HUM
h
MI N
%
F
AUTOFAN
h
MI N
%
F
to save the value.
On the display, the following
SET
IN
1
2
ON
OFF
C
FAN
appears. Water inlet temperature will appear after 3 seconds.