poolstar POOLEX VARILINE PF-VL10P User manual
VARILINE
Variable speed filtration pump
GARANTIE
OWNER’S MANUAL
ANS
Long Life 4 programmable
speeds
3 years
warranty
Silent
Eciency
Energy saving
2
TABLE OF CONTENTS 1. SAFETY INSTRUCTIONS
1 . Safety Instructions ................................................................................................ 3
2. Pump Overview ....................................................................................................... 8
2.1 Pump Overview.............................................................................................. 8
2.2 General Features........................................................................................... 8
2.3 Controller Features ........................................................................................ 9.
2.4 Controller Overview ....................................................................................... 9
3. Control Panel Overview ....................................................................................... 10
3.1 Keypad Navigation....................................................................................... 10
4. Installation ............................................................................................................. 11
4.1 Location ....................................................................................................... 11
4.2 Piping........................................................................................................... 12
4.3 Fitting and Valves......................................................................................... 12
4.4 Electrical Requirements............................................................................... 12
4.5 Wiring Overview and Installation.................................................................. 13
5. Operating the Pump ............................................................................................. 15
5.1 Setting the Clock.......................................................................................... 15
5.2 Using the Default Schedule ......................................................................... 16
5.3 Custom Schedules and quick clean ............................................................ 17
5.4 Speed Priorities............................................................................................ 19
5.5 Operating the Pump While Running ............................................................ 19
6. Maintenance .......................................................................................................... 20
6.1 Pump Strainer Basket.................................................................................. 20
6.2 Cleaning the Pump Strainer Basket............................................................. 20
6.3 Winterizing ................................................................................................... 21
7. Servicing ............................................................................................................... 22
7.1 Electric Motor Care ...................................................................................... 22
7.2 Restart Instructions...................................................................................... 23
8. Troubleshooting ................................................................................................... 25
8.1 Errors and Alarms ........................................................................................ 27
9. Replacement Parts ............................................................................................... 28
9.1 Variable Speed Pump Replacement Parts List............................................ 29
.................................................................................... 30
9.3 Pump Performance Curves ......................................................................... 31
9.4 Pump Dimensions........................................................................................ 32
10. Warranties ........................................................................................................... 33
3
1. SAFETY INSTRUCTIONS
This guide provides installation and operation instructions for this pump. Consult
distributor with any questions regarding this equipment.
Attention Installer: This guide contains important information about the installation,
operation and safe use of this product. This information should be given to the owner
and/or operator of this equipment after installation or left on or near the pump.
Attention User: This manual contains important information that will help you in
operating and maintaining this product. Please retain it for future reference.
Important notice
This is the safety alert symbol. When you see this symbol on your
system or in this manual, look for one of the following signal words
and be alert to the potential for personal injury.
READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should
always be followed, include the following:
WARNING - Do not permit children to use this product.
WARNING - RISK OF ELECTRICAL SHOCK. Connect only to a branch circuit
DANGER - Warns about hazards that can cause death, serious personal injury,
or major property damage if ignored.
WARNING - Warns about hazards that may cause death, serious personal injury,
or major property damage if ignored.
CAUTION - Warns about hazards that may or can cause minor personal injury or
property damage
if ignored.
NOTE : Indicates special instructions not related to hazards.
Carefully read and follow all safety instructions in this manual and on equipment. Keep
safety labels in good condition; replace if missing or damaged.
4
1. SAFETY INSTRUCTIONS
WARNING - This unit must be connected only to a supply circuit that is protected by
and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI
should interrupt power. Push the reset button. Power should be restored. If the GFCI
fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the
possibility of an electric shock. Do not use this pump. Disconnect the pump and have the
CAUTION - This pump is for use with permanent swimming pools and may also be
used with hot tubs and spas if so marked. Do not use with storable pools. A permanently-
installed pool is constructed in or on the ground or in a building such that it cannot be
readily disassembled for storage. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity.
General Warnings
• Never open the inside of the drive motor enclosure. There is a capacitor bank that holds
a 220-24 0 VAC charge even when there is no power to the unit.
• The pump is not submersible.
to limit pumps performance potential with old or questionable equipment.
state, as well as local municipalities. Install equipment in accordance with the National
Electrical Code and all applicable local codes and ordinances.
• Before servicing the pump; switch OFF power to the pump by disconnecting the main
circuit to the pump.
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance by
a person responsible for their safety.
DANGER - FAILURE TO FOLLOW ALL INSTRUCTIONS AND WARNINGS
CAN RESULT IN SERIOUS BODILY INJURY OR DEATH. THIS PUMP SHOULD
BE INSTALLED AND SERVICED ONLY BY A QUALIFIED POOL SERVICE
PROFESSIONAL. INSTALLERS, POOL OPERATORS AND OWNERS MUST READ
THESE WARNINGS AND ALL INSTRUCTIONS IN THE OWNER’S MANUAL BEFORE
USING THIS PUMP. THESE WARNINGS AND THE OWNER’S MANUAL MUST BE
LEFT WITH THE POOL OWNER.
SUCTION ENTRAPMENT HAZARD: STAY OFF THE MAIN DRAIN AND AWAY FROM
ALL SUCTION OUTLETS!
5
1. SAFETY INSTRUCTIONS
THIS PUMP PRODUCES HIGH LEVELS OF SUCTION AND CREATES A STRONG
VACUUM AT THE MAIN DRAIN AT THE BOTTOM OF THE BODY OF WATER. THIS
SUCTION IS SO STRONG THAT IT CAN TRAP ADULTS OR CHILDREN UNDER
WATER IF THEY COME IN CLOSE PROXIMITY TO A DRAIN OR A LOOSE OR
BROKEN DRAIN COVER OR GRATE.
THE USE OF UNAPPROVED COVERS OR ALLOWING USE OF THE POOL OR SPA
WHEN COVERS ARE MISSING, CRACKED OR BROKEN CAN RESULT IN BODY OR
LIMB ENTRAPMENT, HAIR ENTANGLEMENT, BODY ENTRAPMENT, EVISCERATION
AND/OR DEATH.
WARNING - TO MINIMIZE THE RISK OF INJURY DUE TO SUCTION ENTRAPMENT
HAZARD:
• A properly installed and secured , according to the standards in force in the country
concerned, approved anti-entrapment suction cover must be used for each drain.
• Regularly inspect all covers for cracks, damage and advanced weathering.
• If a cover becomes loose, cracked, damaged, broken or is missing, replace with an
• Replace drain covers as necessary. Drain covers deteriorate over time due to exposure
to sunlight and weather.
• Avoid getting hair, limbs or body in close proximity to any suction cover, pool drain or
outlet.
6
1. SAFETY INSTRUCTIONS
WARNING -
an easily accessible, obvious place.
TO MINIMIZE THE RISK OF INJURY DUE TO SUCTION ENTRAPMENT HAZARD:
Make sure users know where it is and how to use it in case of emergency.
For Installation of Electrical Controls at Equipment Pad (ON/OFF Switches, Timers
and Automation Load Center)
CAUTION -
DANGER -HAZARDOUS PRESSURE: STAND CLEAR OF PUMP AND FILTER
DURING START UP
Circulation systems operate under high pressure. When any part of the circulating
and valves to violently separate which can result in severe personal injury or death. Filter
tank lid and strainer cover must be properly secured to prevent violent separation. Stand
clear of all circulation system equipment when turning on or starting up pump.
the pump. IMPORTANT: Place lter manual air relief valve in the open position and
wait for all pressure in the system to be relieved.
Before starting the system, fully open the manual air relief valve and place all system
tank. Stand clear of all equipment and start the pump.
IMPORTANT: Do not close lter manual air relief valve until all pressure has been
discharged from the valve and a steady stream of water appears. Observe lter
pressure gauge and be sure it is not higher than the pre-service condition.
General Installation Information
national, state, and local codes.
• Install to provide drainage of compartment for electrical components.
• These instructions contain information for a variety of pump models and therefore
swimming pool applications. The pump will function correctly only if it is properly sized to
7
1. SAFETY INSTRUCTIONS
WARNING - Pumps improperly sized or installed or used in applications other than
for which the pump was intended can result in severe personal injury or death. These
or severe injury or property damage caused by a structural failure of the pump or other
system component.
WARNING - The pump is not intended for use by young supervision. Young children
should be supervised to ensure that they do not play with the pump. children or from
persons without
WARNING - If the supply cord is damaged, it must be replaced by the manufacturer,
SAVE THESE INSTRUCTIONS
8
2. PUMP OVERVIEW
The perfect choice for all types of pools, the Variable Speed Pump was specifcally
designed to be your best choice for a variety of in-ground pools.
Thick walled body parts, a heavy duty TEFC motor, and highly engineered hydraulics
make this rugged and tested design perfect for any pool, spa, water feature, or
fountain.
2.1 Pump Overview
2.2 General features
Variable Speed Pump
• Extremely quiet operation
replacement
• Strainer cover kit for easy cleaning and
maintenance
motor for long life
• Integral volute and pot reduce hydraulic noise
• See-through lid permits easy inspection of
strainer basket
• Self-priming for quick, easy start-up
• ETLUS/CETL Listed
9
2. PUMP OVERVIEW
2.3 Controller Features
2.4 Controller Overview
• Simple user interface
• IPX4 certifed UV and rain-proof enclosure
• Onboard time of day schedule
• Adjustable priming mode
• Programmable quick clean mode
• Diagnostic alarm display and retention
• Active power factor correction
• Accepts 220-240V, 50/60Hz input power
• Auto power limiting protection circuit
• One week. clock retention for power outages
settings. The pump is intended to run at the lowest speeds needed to maintain a
sanitary environment, which in turn minimizes energy consumption. Pool size, the
presence of additional water features, chemicals used to maintain sanitary conditions,
and local environmental factors will impact optimal programming necessary to
maximize energy conservation.
WARNING - This pump is for use with 220-240 V nominal, and in pool pump applications
ONLY. Connection to the wrong voltage, or use in other application may cause damage to equipment
or personal injury.
The integrated electronics interface controls the speed settings as well as the run
durations. The pump can operate at speeds ranging between 450 and 3450 RPM and
will operate within the voltage range of 220-240V at either 50 or 60Hz input frequency.
Program customization may require some trial-and-error to determine the most
satisfactory settings as dictated by the conditions. In most cases, setting the pump
at the lowest speed for the longest duration is the best strategy to minimize energy
consumption. However, conditions may require running the pump at a higher speed
sanitation.
NOTE
including pool size, other devices, features and environmental factors can all impact
the optimal settings.
10
3. CONTROL PANEL OVERVIEW
1. Speed Buttons - Used to select the run speed desired. The LED above the Speed
Buttons will illuminate when that speed is selected or is currently running. A fashing
LED indicates is active on that speeds channel.
2. Mode select Button - Choose manual and schdule
3. Start/Stop Button - Used to Start and Stop the pump. When the pump is stopped
and the LED is not illuminated, the pump is unable to run from any type of input.
4. Display Mode LED Indicators - An illuminated LED indicates the information
parameter is currently being edited.
5. Display Button
button is also used to set the 24-hour clock and screen resolution.
6. Quick Clean Button - Used to run a selected speed and duration programmed for
Quick Clean. When the LED is illuminated the Quick Clean schedule is active.
7. «<» and «>» Arrows- Choose between a 12 or 24 hour time format
8. “+” and “-” Arrows - Used to make on screen adjustments to the pump settings.
The “+” arrow increases the value of a given setting, while “-” decreases the value of a
given setting. Pressing and holding down either arrow button will increase or decrease
the incremental changes faster.
3.1 Keypad Navigation
CAUTION - If power is connected to the Variable Speed Pump motor, pressing any of the
following buttons referred to in this section could result in the motor starting. Failure to recognize
this could result in personal injury or damage to equipment.
(4) Display Mode
LED Indicators
(5) Display Button
(6) Quick Clean
Button
(3) Start/Stop
Button
(1) Speed
Buttons
(8) “+” and “-”
Arrows
(7)»<» and «>»
Arrows
(2) Mode Select
Button
11
4. INSTALLATION
4.1 Location
Only a qualifed plumbing professional should install the Variable Speed Pump. Refer to
“Safety Instructions” for additional installation and safety information.
NOTE: Do not install this pump within an outer enclosure
or beneath the skirt of a hot tub or spa unless marked
accordingly.
NOTE: Ensure that the pump is mechanically secured to the
equipment pad.
Be sure the pump location meets the following
requirements:
1. Install the pump as close to the pool or spa as possible. To reduce friction loss and
the pool.
5. Install the pump in a well ventilated location protected from excess moisture (i.e. rain
can be removed easily for maintenance and repair. See Figure 1.
15cm
15cm
12
4.2 Pipping
1. For improved pool plumbing, it is recommended to use a larger pipe size.
2. Piping on the suction side of the pump should be the same or larger than the return
line diameter.
3. Plumbing on the suction side of the pump should be as short as possible.
4. For most installations , always installing a v alve on both the pump suction and return
lines so that the pump can be isolated during routine maintenance. However, we also
recommend that a valve, elbow or tee installed in the suction line should be no closer
Figure 2.
Example
suction inlet of the pump. This will help the pump prime faster and last longer.
NOTE: DO NOT install 90° elbows directly into the pump inlet or outlet.
4.3 Fitting and Valves
1. Do not install 90° elbows directly into pump inlet.
2. Flooded suction systems should have gate valves installed on suction and discharge
times the suction pipe diameter as described in this section.
3. Use a check valve in the discharge line when using this pump for any application
4. Be sure to install check valves when plumbing in parallel with another pump. This
helps prevent reverse rotation of the impeller and motor.
4.4 Electrical Requirements
• Install all equipment in accordance with the National Electrical code and all applicable
local codes and ordinances
the wiring rules.
4. INSTALLATION
13
4. INSTALLATION 4. INSTALLATION
4.5 Wiring Overview and Installation
WARNING - RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. The Variable Speed
in accordance with the National Electrical Code and all applicable local codes and ordinances.
Improper installation will create an electrical hazard which could result in death or serious injury to
users, installers, or others due to electrical shock, and may also cause damage to property.
Always disconnect power to the pump at the circuit breaker before servicing the pump.
Failure to do so could result in death or serious injury to service people, pool users or others
due to electric shock and/or property damage.
Read all servicing instructions before working on the pump.
WARNING -
components. Observe all warning notices posted on the existing equipment, pump, and in these
installation instructions.
The pump must be wired according to the local electrical codes and standards. Always
refer to the National Electrical Code. This pump should be installed by a licensed
electrician.
The pump accepts 220V-240V, 50 or 60Hz single phase Input power. The terminal
block connections are capable of handling up to 12AWG solid or stranded wire. There
are also fast-on type quick connectors, however, check the local electrical codes for
the desired connection method. The connections must be permanently made to the
electrical code.
The drive will operate on 2-phase Line-Line-Ground electrical systems as well as
Line-Neutral-Ground systems. This pump must be permanently connected by a circuit
opening or servicing the drive.
2. Choose a wire size for the pump in accordance with the current National Electrical
Code and all applicable local codes and ordinances. When in doubt use a heavier
3. Be sure all electrical connections are clean and tight.
4. Cut wires to the appropriate length so they do not overlap or touch when connected
to the terminal board.
5. Permanently ground the motor using the ground screw located on the inside rear
by the current National Electrical Code. Be sure the ground wire is connected to an
electrical service ground.
14
6. Bond the motor to all metal parts of the pool structure and to all electrical equipment,
swimming pool, spa or hot tub in accordance with the current National Electrical Code.
UL requires use of a solid copper bonding conductor not smaller than 8 AWG. See
Figure 3.
NOTE: For Canada, a 6 AWG or larger solid copper bonding conductor is required.
7. The pump should be permanently connected to either a circuit breaker, 2-pole timer
or 2-pole relay. If AC power is supplied by a GFCI circuit breaker, use a dedicated
circuit breaker that has no other electrical loads.
8. Connect the pump permanently to a circuit. Make sure no other lights or appliances
are on the same
4. INSTALLATION
The bonding lug should be used to bond the motor frame to the equipment pad.
15
4. INSTALLATION 5. OPERATING THE PUMP
5.1 Setting the Clock
the user must be based on accurate time setting.
To Set the Clock:
1. When the pump is plugged in, the TIME led light is blinking. Entering clock setup by
pushing Display key.
(Time setup will be unavailable after 5 seconds’ blinking. Note:Pump must be
plugged out and ensure the lights on panel all go out, then re-plug it to enter the
setup and operate step 1.)
2. Use the (<) and (>) arrows to choose between a 12 or 24 hour time format.
3. Use the (+) and (-) arrows to change the time to the correct time of day. In the 12
hour time format AM/PM will display in the bottom left corner.
4. Press Display to exit the Clock Setup menu. The clock is now set.
During a power outage, the drive will retain the clock setting in memory for as long as
one week. If the power is out longer than one week the clock will have to be set again.
(Pump must be plugged out and ensure the lights on panel all go out, then re-
plug it to enter the setup and operate step 1.)
NOTE:
clock will automatically set itself to the Speed 1 start time, blink and advance. The
pump will also run the associated schedule from that start time.
16
5.2 Using the Default Schedule
The default schedule is designed to provide enough daily turnover to service a typical
pool. See Table 2 for default schedule.
SPEED 1 is set to begin at 8:00am and run at 3000 RPM for a duration of 2 hours.
When SPEED 1 is complete the pump immediately begins running the default SPEED
2. SPEED 2 is factory default to 1500 RPM and will last for 10 hours. When SPEED 2
has completed its run the pump will run SPEED 3 at 2500 RPM for a duration of two
hours.
After 18 hours of run time and completing its run of SPEED 4, the pump will enter a
stationary/paused state for the next 6 hours. The pump will restart at 8:00am the next
morning and cycle through the default schedule again. The pump will continue to run
in this in this manner until a custom schedule is programmed into the drive by the user.
NOTE: The Start/Stop button must be pressed, and the LED lit, for the pump to run.
Speed 1 and priming
The installer should set the priming speed to be sucient for priming the pump
from a fresh install,but not so fast that there is a substantial waste of energy. The
time the pump needs to achieve prime can change based on local environmental
conditions such as water temperature, atmospheric pressure, and your pool’s
water level. All of these things should be taken into consideration when setting
the priming speed, however in most cases the pump will not need to run at 3450
RPM to successfully prime itself.
Please test and verify chosen priming speeds more than once, letting the water
drain from the system in between each test. Turn on pump and switch to Manual
mode to test Priming by operating SPEED1.Take note of the time that the water
lled the PUMP HOUSING, then stop the pump. Re-start the pump to set the
SPEED1/Priming duration.
Duration
(Hours)
Speed
(RPM)
SPEED 1 2 3000
SPEED 2 10 1500
SPEED 3 2 2500
SPEED 4 4 1000
Table 2: Default Schedule
5. OPERATING THE PUMP
17
5.3 Custom Schedules and Quick Clean
To customize the run schedule for your Variable Speed Pump, the pump must be
stopped. Be sure that the Start/Stop button LED is not illuminated.
Programming a Custom Schedule:
NOTE: When programming, the LED light next to the parameter (“Speed”, “Time” and
“Duration”
1.Stop the pump if it is running by pressing the Start/Stop button.
2.Press the “1” button. The LED above the selected SPEED will begin to blink and the
“Speed” parameter LED will blink while editing. See Figure 7.
Figure 7: Setting Speed
3.Use the “+” and “-” arrows to adjust the speed in RPM for SPEED 1.
NOTE: Speed is adjusted up or down by increments of 10 RPM.
4.Press the “1” button again and the display will change to SPEED 1 start time. The
“Time” parameter LED will begin to blink. See Figure 8.
Figure 8: Setting Start Time
5. OPERATING THE PUMP
18
5. OPERATING THE PUMP
5.Use the “+” and “-” arrows to adjust the daily start time for SPEED 1.
6.Press the “1” button again and the display will change to SPEED 1 duration. The
“Duration” parameter LED will begin to blink. See Figure 9.
7. Use the “+” and “-” arrows to adjust the duration for SPEED 1 in hours and minutes.
NOTE: The duration parameter is adjusted in 15 minute increments.
8.Pressing the “1” button will continue to cycle through these parameters, but the
changes are immediately saved as they are adjusted.
9.Press the “2”
10.Use the “+” and “-” arrows to adjust the speed in RPM for SPEED 2.
11.Press the “2” button again and the display will change to SPEED 2 duration.
Note: SPEEDs 2 and 3 do not have a start time, as they begin their duration
12.Use the “+” and “-” arrows to adjust the duration for SPEED 2 in hours and minutes.
13.Repeat steps 9-12 to program SPEED 3-4 and QUICK CLEAN.
Note: Remember that the duration allowed for SPEED 3 will be limited to the remaining
time in a 24 hour day. Any time in the 24 hour day not programmed into SPEEDs 1-4,
the pump will remain in a stationary state.
[ SPEED 1 + SPEED 2 + SPEED 3 +SPEED 4< 24 Hours ]
14.Press the Start/Stop button and ensure the LED is lit. The pump is now on and will
run the custom user-programmed schedule.
NOTE: If the pump has been stopped via the Start/Stop button, the pump will not run
until the pump is turned back on by the Start/Stop button. If the Start/Stop LED is
illuminated then the pump is on and will run the programmed schedule.
Figure 9: Setting Duration
19
5. OPERATING THE PUMP
For schedule duration settings, SPEEDS are prioritized as follows: SPEED 1 ->
SPEED 2 -> SPEED 3 -> SPEED 4. SPEED 1 is the highest priority,while SPEED 4
is the lowest. The drive will not allow a user to program a schedule of more than 24
hours. When the 24th hour of duration is programmed it will take time from the lower
priority speeds in order to add them to the SPEED currently being adjusted.
Example:
SPEED 1 duration = 18 hours
SPEED 2 duration = 2 hours
SPEED 3 duration = 2 hours
adjust to a 0 hour duration.
SPEED 1 duration = 22 hours
SPEED 2 duration = 1 hour
SPEED 3 duration = 1 hours
SPEED 4 duration = 2 hours
SPEED 4 duration = 0 hours
CAUTION - If power is connected to the pump motor, pressing any of the following buttons
referred to in this section could result in the motor starting. Failure to recognize this could result in
personal injury or damage to equipment.
Pressing the Display button will cycle through the current
parameters.
• Speed — current run speed
•Time — current time of day
• Duration — amount of time remaining at the current run speed
• Watts — amount of watts currently being consumed
Pressing any of the Speed Buttons (“1”, “2”, “3”, “4”,“Quick Clean”
is running will act as temporary override. It will run the speed and duration that is
programmed for that button. Once completed it will default back to the appropriate point
in the programmed schedule.
NOTE: If you adjust the speeds of the schedule while the pump is running, it will
run the adjusted speed for the rest of the current duration, but will not save the
adjustments.
5. OPERATING THE PUMP
5.5 Operating the Pump While Running
5.4 Speed priorities
20
6. MAINTENANCE
WARNING - DO NOT open the strainer pot if Variable Speed Pump fails to prime or if pump
has been operating without water in the strainer pot. Pumps operated in these circumstances may
experience a build up of vapor pressure and may contain scalding hot water. Opening the pump
may cause serious personal injury. In order to avoid the possibility of personal injury, make sure
the suction and discharge valves are open and strainer pot temperature is cool to touch, then open
with extreme caution.
CAUTION -To prevent damage to the pump and for proper operation of the system, clean
pump strainer and skimmer baskets regularly.
6.1 Pump Strainer Basket
6.2 Cleaning the Pump Strainer Basket
volute. Inside the chamber is the basket which must be kept clean of leaves and debris
at all times. View basket through the ‘See Through Lid’ to inspect for leaves and debris.
inspect the basket at least once a week.
breaker.
2. Relieve pressure in the system by allowing the water to cool.
3. Gently tap the clamp in a counter-clockwise direction to remove the clamp and lid.
4. Remove debris and rinse out the basket. Replace the basket if it is cracked.
5. Put the basket back into the housing. Be sure to align the notch in the bottom of the
basket with the rib in the bottom of the volute.
6. Fill the pump pot and volute up to the inlet port with water.
7. Clean the cover, O-ring, and sealing surface of the pump pot. Note: It is important to
keep the lid O-ring clean and well lubricated.
8. Reinstall the lid by placing the lid on the pot. Be sure the lid O-ring is properly placed.
Seat the clamp and lid on the pump then turn clockwise until the handles are horizontal.
9. Turn the power on at the house circuit breaker. Reset the pool time clock to the correct
time, if applicable.
air relief valve.
This manual suits for next models
4
Table of contents
Other poolstar Water Pump manuals
Popular Water Pump manuals by other brands
Armstrong
Armstrong 4302 Series manual
Xylem
Xylem Flygt 3127 Installation, operation and maintenance manual
Misters Unlimited
Misters Unlimited Mister PM10 Installation & operation instructions
Wilo
Wilo BF Series operating instructions
TLV
TLV CP-N instruction manual
Trotec
Trotec TWP 4025 E operating manual
Grundfos
Grundfos S Series Installation and operating instructions
Grundfos
Grundfos DP 10 Installation and operating instructions
Alemite
Alemite 7889-6 Service guide
Waterous
Waterous CZ Series Operation and maintenance manual
GORMAN-RUPP PUMPS
GORMAN-RUPP PUMPS 02D3-B Installation, operation and maintenance manual
Agilent Technologies
Agilent Technologies 1260 Infinity Quaternary LC VL System Manual and Quick Reference
