poolstar SUP STAR PUMP-8 User manual

HT-782 Operation Instructions
Intelligent DC Electric Pump
Please read the operation instructions carefully before using this product.
Please operate in the correct way based on complete understanding.
Manufacturer:
Dongguan Huatao Metal and Plastic Products Co., Ltd.
Manufacturer's address:
Yanhe East Road, Xiabian Avenue, Chang'an Town,
Dongguan City, Guangdong Province, China
SUP ELECTRIC AIR PUMPSUP ELECTRIC AIR PUMP
INTELLIGENT DC ELECTRIC AIR PUMP
POMPE DE GONFLAGE ÉLECTRIQUE
STARPUMP-8
Operation Instructions
Manuel d’utilisation
Please read the operation instructions carefully before using this product.
Please operate in the correct way based on complete understanding.
Veuillez lire attentivement les instruction avant d’utiliser le produit.
Utilisez le produit conformément aux instructions situées dans ce manuel.
PUMP

/2 STARPUMP 8
CATALOGUE
I. Product introduction / Introduction 2
II. List of accessories / Contenu du produit 3
III. Details of acessories / Détail des accessoires 3
IV. Safety instruction / Avertissements de sécurité 4-5
V. Ination Operation / mode gonage 6-7
VI. Deatation Operation / mode dégonage 8-9
VI. Precautions / Mise en garde 8-9
VII. Fault Handling / Pannes et anomalies 10
VIII. Maintenance and storage / Entretien et stockage 11
IX. Warranty / Garantie 11
I. PRODUCT INTRODUCTION / INTRODUCTION
Thank you for purchasing this product, STARPUMP-8 is an intelligent DC
electric pump with the preset pressure LCD screen, which can be used
for inatable tent, SUP, etc. Thanks to the intelligent pressure system, for
example, if a pressure value is preset, when the pressure reaches the
preset pressure value, the pump will automatically stop inating.
This product also can deation, and when the inatable product is not
used, you can use the air pump to empty the air inside for folding and
storage.
Nous vous remercions pour l’achat de notre produit. La STARPUMP-8 est
une pompe de gonage électrique pour le gonage de SUP ou mate-
las gonable, etc. Elle est équipée d’un écran LCD et d’un système de
pression intelligent qui lui permet de s’arrêter une fois que la pression
préalablement paramétrée est atteinte.
Cette pompe permet également de dégoner nos produits gonables. Ils
sont ainsi plus faciles à entreposer et à transporter.

STARPUMP 8 /3
II. LIST OF ACCESSORIES / CONTENU DU PRODUIT
Please make sure that the following accessories are in the box before
using it, if any missing, please contact with the local supplier.
Vériez que l’ensemble des éléments ci-dessous sont bien présents
dans le packaging. Si un élément est manquant, merci de contacter votre
revendeur.
III. Details of acessories / Détail des accessoires
I. Product Introduction
Thank you for purchasing this product, HT-782 is an intelligent DC electric
pump with the preset pressure LCD screen, which can be used for inflatable
tent, SUP, etc. Thanks to the intelligent pressure system, for example, if a
pressure value is preset, when the pressure reaches the preset pressure
value, the pump will automatically stop inflating.
This product also can deflation, and when the inflatable product is not used,
you can use the air pump to empty the air inside for folding and storage.
II. List of Accessories
Please make sure that the following accessories are in the box before using
it, if any missing, please contact with the local service agents
SUP ELECTRIC AIR PUMPSUP ELECTRIC AIR PUMP
Air pump Hose Instruction Book
Inflation inlet
Deflation outlet
DC plug
Pressure value LCD screen
Pressure unit toggle button
Pressurizing button
Decompressing button
On/off button
Hose
Air tap
Flexible conduit adaptor
III. Details of Accessories
4
1
5
6
7
81
2
3
4
5
6
7
8
9
10
11
1
3
2
11
10
9
20.00
I. Product Introduction.......................................1
II. List of Accessories........................................1
III. Details of Accessories..................................1
IV. Safety Instructions........................................2
V. Inflation Operation......................................3-4
VI. Deflation Operation......................................4
VII. Precautions..............................................4-5
VIII. Fault Handling............................................5
IX. Maintenance and Storage...........................5
X. Suggestions..................................................5
I. Product Introduction
Thank you for purchasing this product, HT-782 is an intelligent DC electric
pump with the preset pressure LCD screen, which can be used for inflatable
tent, SUP, etc. Thanks to the intelligent pressure system, for example, if a
pressure value is preset, when the pressure reaches the preset pressure
value, the pump will automatically stop inflating.
This product also can deflation, and when the inflatable product is not used,
you can use the air pump to empty the air inside for folding and storage.
II. List of Accessories
Please make sure that the following accessories are in the box before using
it, if any missing, please contact with the local service agents
SUP ELECTRIC AIR PUMPSUP ELECTRIC AIR PUMP
Air pump Hose Instruction Book
Inflation inlet
Deflation outlet
DC plug
Pressure value LCD screen
Pressure unit toggle button
Pressurizing button
Decompressing button
On/off button
Hose
Air tap
Flexible conduit adaptor
III. Details of Accessories
4
1
5
6
7
8
1
2
3
4
5
6
7
8
9
10
11
1
3
2
11
10
9
20.00
I. Product Introduction.......................................1
II. List of Accessories........................................1
III. Details of Accessories..................................1
IV. Safety Instructions........................................2
V. Inflation Operation......................................3-4
VI. Deflation Operation......................................4
VII. Precautions..............................................4-5
VIII. Fault Handling............................................5
IX. Maintenance and Storage...........................5
X. Suggestions..................................................5
(1) Ination inlet
raccord de gonage
(2) Deation outlet
raccord de dégonage
(3) DC plug / Prise de courant
(4) Pressure value LCD screen
Ecran LCD
(5) Pressure unit toggle button
Bouton de changement d’unité
(6) Pressurizing button
Bouton d’augmentation
(7) Decompressing button
Bouton de diminussion
(8) On/o󰀨 button / Bouton On/o
(9) Hose / Tuyau exible
(10) Air trap / Sortie d’air
(11) Flexible conduit adaptor
adaptateur de tuyau
Air Pump
Pompe électrique
Hose
Raccord d’air
Instruction Book
Manuel

/4 STARPUMP 8
IV. SAFETY INSTRUCTIONS
•Warning: In order to reduce the risk of injury, please keep children away
• from it. Always supervise children and incapacitated person contacting or
• using this air pump.
•Warning: Children shall be kept far away from this product and wire.
•Warning: This product is not applicable for the person with declining
• physical strength, sensory ability or mental capacity, the person lack of
• skill and the mentally retarded person, unless they are under the
• protection of their guardians, supervised and directed at the same time.
•Warning: Before moving, maintaining, repairing or adjusting this
• product, please rst pull out the DC plug from the socket.
•Warning: Please do not bury the wire in the soil, and it shall be place in
• the safe zone where it won’t be damaged by mower or other equipment.
•Warning: If the power wire is damaged, the power wire must be
• changed by the manufacturer or its service agent or the similar
• authorized personnel, in case of any risk.
•Warning: If you are standing in a place with water or your hands are
• wet, please don’t plug or pull the DC plug.
•Warning: Before inating, please pay attention to check the maximum
• bearable pressure of the inatable product, because the air bag may be
• damaged upon exceeding the maximum bearable pressure.
•Warning: Before using, please check the cigarette lighter socket to
• make sure that there is no rust or residue inside. The cigarette lighter
• socket with poor electric conduction may cause overheating of the
• product or power source, which will damage the product.
•Warning: The purpose of using this product is limited to the description
• in the instruction book.

STARPUMP 8 /5
IV. AVERTISSEMENTS DE SÉCURITÉ
Attention: An de réduire le risque de blessures, veuillez tenir les enfants
à l’écart. Surveillez toujours les enfants et les personnes handicapées qui
entrent en contact avec ou utilisent cette pompe à air.
Attention: Les enfants doivent être tenus à l’écart de ce produit et des
ls.
Attention: Ce produit n’est pas adapté aux personnes dont la force phy-
sique, la capacité sensorielle ou mentale est diminuée, sauf si celle-ci est
sous supervision d’un tuteur.
Attention: Avant de déplacer ou entretenir ce produit, veillez à la mettre
hors tension.
Attention: Veillez à ce que le câble d’alimentation ne soit jamais enterré,
et soit dans une zone sécurisée. Ne pas endommager le l par d’autres
équipements.
Attention: Si le câble d’alimentation est endommagé, il doit être remplacé
uniquement par le fabriquant.
Attention: Ne branchez ou débranchez pas le câble électrique si vos
mains sont mouillées ou si vous vous trouvez dans un endroit présentant
de l’eau sur le sol.
Attention: Avant la mise en route, vériez la pression maximale suppor-
table de votre produit gonable, car celui-ci peut être endommagé en cas
de surpression, même brève.
Attention: Vériez toujours l’état de la prise allume-cigare avant de bran-
cher l’appareil. Elle ne doit pas présenter de rouille ou de déformation.
En cas de mauvaise connection électrique, celle-ci peut provoquer une
surchau󰀨e du produit et l’endommager.
Attention: L’utilisation de ce produit se limite à la description du manuel
d’instructions.

/6 STARPUMP 8
V. INFLATION OPERATION
• Connect the end with Flexible conduit adaptor of the hose with the air
pump ination inlet (1), and twist clockwise to tighten it, as Figure 1.
• Install the other end of the hose into the supporting air tap of the air bag
(step(1) in Figure 2), and twist clockwise to tighten it, and then insert the
ination valve of the air bag and twist clockwise to x it (step(2) in Figure
2).
• Plug the DC plug into the 12V DC socket.
• Press the pressure unit toggle button to select the unit you need.
• Press the pressurizing button or decompressing button to set
the pressure value you need, with the range of the pressure value from 0
to 20PSI, (1PSI=0.0689BAR)
• After nishing the above steps, press the power switch button to
start to inate.
• During the inating process, you can press the pressurizing button
or decompressing button to increase or reduce the pressure value,
press the pressure unit toggle button to switch the unit, and press
the On/O󰀨 button to stop.
• When the pressure reaches the set value, the air pump will stop working
• automatically.
• After completing the ination, pull out the DC plug from the 12V DC
• socket.
• After pulling out the DC plug, please take down the hose from the air
• pump and air bag and store it.
• Notice: The factory set pressure value of the air pump is 10PSI (10PSI=0.
689BAR), and at the time of the secondary use, the set pressure value
for the last time use will be displayed by default.
• Notice: After powered on, if there is no operation within 2 minutes, the
air pump will enter standby mode, and the machine can be initiated by
pressing the power switch button .
2 3
IV. Safety Instructions
Warning: In order to reduce the risk of injury, please keep children away
from it. Always supervise children and incapacitated person contacting or
using this air pump.
Warning: Children shall be kept far away from this product and wire.
Warning: This product is not applicable for the person with declining
physical strength, sensory ability or mental capacity, the person lack of
skill and the mentally retarded person, unless they are under the
protection of their guardians, supervised and directed at the same time.
Warning: Before moving, maintaining, repairing or adjusting this
product, please first pull out the DC plug from the socket.
Warning: Please do not bury the wire in the soil, and it shall be place in
the safe zone where it won't be damaged by mower or other equipment.
Warning: If the power wire is damaged, the power wire must be
changed by the manufacturer or its service agent or the similar
authorized personnel, in case of any risk.
Warning: If you are standing in a place with water or your hands are
wet, please don't plug or pull the DC plug.
Warning: Before inflating, please pay attention to check the maximum
bearable pressure of the inflatable product, because the air bag may be
damaged upon exceeding the maximum bearable pressure.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
Warning: The purpose of using this product is limited to the description
in the instruction book.
（Figure 1） （Figure 2）
When the pressure reaches the set value, the air pump will stop working
automatically.
After completing the inflation, pull out the DC plug from the 12V DC
socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag and store it.
*
*
*
V. Inflation Operation
Connect the end with flexible conduit adaptor （11）of the hose with the
air pump inflation inlet (1), and twist clockwise to tighten it, as Figure 1.
Install the other end of the hose into the supporting air tap of the air
bag (step①in Figure 2), and twist clockwise to tighten it, and then
insert the inflation valve of the air bag and twist clockwise to fix it (step
②in Figure 2).
Plug the DC plug into the 12V DC socket.
Press the pressure unit toggle button to select the unit you need.
Press the pressurizing button or decompressing button to
set the pressure value you need, with the range of the pressure value
from 0 to 16PSI, (1PSI=0.0689BAR)
After finishing the above steps, press the power switch button to
start to inflate.
During the inflating process, you can press the pressurizing button or
decompressing button to increase or reduce the pressure value, press
the pressure unit toggle button to switch the unit, and press the On/Off
button to stop.
*
*
*
*
*
*
*
*
*
*
*
*
HT-782 DC12V HT-782 DC12V
*
*
*
*
*

STARPUMP 8 /7
2 3
IV. Safety Instructions
Warning: In order to reduce the risk of injury, please keep children away
from it. Always supervise children and incapacitated person contacting or
using this air pump.
Warning: Children shall be kept far away from this product and wire.
Warning: This product is not applicable for the person with declining
physical strength, sensory ability or mental capacity, the person lack of
skill and the mentally retarded person, unless they are under the
protection of their guardians, supervised and directed at the same time.
Warning: Before moving, maintaining, repairing or adjusting this
product, please first pull out the DC plug from the socket.
Warning: Please do not bury the wire in the soil, and it shall be place in
the safe zone where it won't be damaged by mower or other equipment.
Warning: If the power wire is damaged, the power wire must be
changed by the manufacturer or its service agent or the similar
authorized personnel, in case of any risk.
Warning: If you are standing in a place with water or your hands are
wet, please don't plug or pull the DC plug.
Warning: Before inflating, please pay attention to check the maximum
bearable pressure of the inflatable product, because the air bag may be
damaged upon exceeding the maximum bearable pressure.
Warning: Before using, please check the cigarette lighter socket to
make sure that there is no rust or residue inside. The cigarette lighter
socket with poor electric conduction may cause overheating of the
product or power source, which will damage the product.
Warning: The purpose of using this product is limited to the description
in the instruction book.
（Figure 1） （Figure 2）
When the pressure reaches the set value, the air pump will stop working
automatically.
After completing the inflation, pull out the DC plug from the 12V DC
socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag and store it.
*
*
*
V. Inflation Operation
Connect the end with flexible conduit adaptor （11）of the hose with the
air pump inflation inlet (1), and twist clockwise to tighten it, as Figure 1.
Install the other end of the hose into the supporting air tap of the air
bag (step①in Figure 2), and twist clockwise to tighten it, and then
insert the inflation valve of the air bag and twist clockwise to fix it (step
②in Figure 2).
Plug the DC plug into the 12V DC socket.
Press the pressure unit toggle button to select the unit you need.
Press the pressurizing button or decompressing button to
set the pressure value you need, with the range of the pressure value
from 0 to 16PSI, (1PSI=0.0689BAR)
After finishing the above steps, press the power switch button to
start to inflate.
During the inflating process, you can press the pressurizing button or
decompressing button to increase or reduce the pressure value, press
the pressure unit toggle button to switch the unit, and press the On/Off
button to stop.
*
*
*
*
*
*
*
*
*
*
*
*
HT-782 DC12V HT-782 DC12V
*
*
*
*
*
V. MODE GONFLAGE
Visser le tuyau d’air à la pompe de gonage dans le sens des aiguilles
d’une montre, puis le serrer
Installez l’autre extrémité du tuyau d’air dans le produit que vous sou-
haitez goner et tournez dans le sens des aiguilles d’une montre, puis le
serrer.
• Branchez la che CC dans la prise 12V (allume-cigare)
• Appuyez sur le bouton de sélection d’unité pour choisir l’unité de
mesure désirée.
• Appuyez sur le bouton d’augmentation ou de diminution pour
choisir la valeur de pression souhaitée, dans l’intervalle de 0 à 20PSI,
(1PSI=0.0689BAR)
• Une fois l’ensemble des étapes validées, appuyez sur le bouton de mise
en route pour démarrer le gonage.
• Pendant le gonage, vous pouvez appuyer sur le bouton d’augmentation
ou de diminution pour ajuster la valeur souhaitée, appuyez sur
le bouton de choix des unités de mesure pour passer d’une unité à
l’autre, et appuyez sur le bouton On/O󰀨 pour arrêter.
• Une fois la pression demandée atteinte, la pompe s’arrête automatique-
ment.
• Une fois le gonage terminé, débrancher la prise de courant 12V CC.
• Débranchez maintenant le tuyau de gonage et rangez le.
• Notice: Le réglage d’usine de la pompe est de 10 PSI
• (10PSI=0.689BAR), lors de votre prochaine utilisation, la dernière valeur
enregistrée est déjà sélectionnée.
• Notice: Si aucune manipulation n’a été e󰀨ectuée après 2 minutes, la
pompe se met en veille,appuyez sur le bouton pour la remettre en
route.

/8 STARPUMP 8
VI. PRECAUTIONS
• The applied power source must be the 12V DC
power source (as Figure 4).
• Do not block the ination inlet (1) and Deation
outlet (2), and ensure that the ination inlet (1) and
Deation outlet (2) shall remain smooth at all times.
• Observe the local waste treatment provisions, and it is not allowed to
throw the air pump away randomly.
• Don’t use this product when the hose is damaged, and please change the
hose immediately.
• Don’t pull out the hose when inating, because that the high pressure
may hurt the physical body.
• Don’t make the air pump work for more than 20 minutes, because that
motor overheating may cause internal damage; and the air pump shall be
fully cooled for 30 minutes after continuously working up to 20 minutes.
• Please don’t use this air pump if any part is damaged, and please contact
• with the professional personnel to repair it.
• This product shall not be exposed to the rain or immersed in water.
• In order to prevent risk, the ination inlet shall not be forward to face or
body.
• Please don’t not leave while inating.
• Please start the car when using the product, in case of unnecessary
• damage.
VI. DEFLATATION OPERATION
• Remove the hose from the ination inlet, Connect the end with exible
conduit adaptor (11) of the hose with the air pump deation outlet (2), and
twist clockwise to tighten it, as Figure 3,and the other end shall still be to
the airbag.
• Press the button of the power switch of air pump, and start the deation
until all the gas is discharged, then the power can be turned o󰀨 to stop
the deation.
14
HT-785
I、Product Introduction
Thank you for purchasing this product. HT-785 is a DC electric air
pump that can inflate inflatable tent, SUP, etc. It has an intelligent
pressure system, such as if you set up the pressue, pump will
automatically stop inflating when pump pressure reaches the preset.
II、List of Accessories
III、List of Accessories
Please make sure that the following accessories are in the box
before using it, if any missing, please contact with the local supplier.
VI. Precautions
ELECTRIC AIR PUMP
Air pump Hose Instruction Book
23
1
4
5
Figure 3
When the pressure reaches the set value, the air pump will stop
working automatically.
After completing the inflation, pull out the DC plug from the 12V
DC socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag, and store it.
The applied power source must be the 12V DC power source
(as Figure 3).
Don't block the air inlet at the bottom of the air
pump, and guarantee air inlet to be always
unblocked.
Observe the local waste treatment provisions, and
it is not allowed to throw the air pump away randomly.
Don't use this product when the hose is damaged, and please change the
hose immediately.
Don't pull out the hose when inflating, because that the high pressure may
hurt the physical body.
Don't make the air pump work for more than 20minutes, because that motor
overheating may cause internal damage; and the air pump shall be fully
cooled for 30 minutes after continuously working up to 20 minutes.
Please don't use this air pump if any part is damaged, and please contact
with the professional person to repair it.
This product shall not be exposed to the rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward to face or body.
Please don't not leave while inflating.
Attention! For best results and to prevent any damage, please start
the car when using the product
5
Please don't use this air pump if any part is damaged, and please contact
with the professional personnel to repair it.
This product shall not be exposed tothe rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward toface or body.
Please don't not leave while inflating.
Please start the car when using the product, in case of unnecessary
damage.
VIII. Fault Handling
Fault Inspection Solution
The air pump
cannot be
started
normally.
1. The power source is
not plugged properly.
2. The fuse in DC plug
(7) is burnt out.
3. Overheating or
overload causes motor
stop.
1. Check whether the
hose is blocked or
cracked.
2. The joint between
the hose and air pump
or air bag is not
installed properly.
1. Make sure that the power wire is
plugged in the 12V DC socket.
2. Change the fuse.
3. Cool the motor and restart it.
4. If the problem cannot be solved,
please contact local service agents or
similar authorized personnel tochange
the product.
1. Change the hose or make it
unblocked, and check whether the hose
is cracked.
2. Reinstall the hose.
3. If the problem cannot be solved,
please contact local service agents or
similar authorized personnel tochange
the product.
Slow or
abnormal
inflation or
deflation.
IX. Maintenance and Storage
After using, or if you want to move, maintain or adjust the product,
please first pull out the DC plug from the socket.
when it is idle, it shall be properly stored after being fully cooled.
It shall not be exposed tothe rain or immersed in water.
Please store it in the dry and ventilated place.
X. Suggestions
The warranty period of this product is one year, and it is suggested to
use the original accessories. For any fault not caused by using the
original accessories, it shall be out of the warranty scope.
*
*
*
*
*
*
*
HT-782 DC12V
4
（Figure 4）
The applied power source must be the 12V DC power source (as Figure 4).
Do not block the inflation inlet (1) and Deflation outlet (2), and ensure that the
inflation inlet (1) and Deflation outlet (2) shall remain smooth at all times.
Observe the local wastetreatment provisions, and it is not allowed tothrow
the air pump away randomly.
Don't use this product when the hose is damaged, and please change the
hose immediately.
Don't pull out the hose when inflating, because that
the high pressure may hurt the physical body.
Don't make the air pump work for more than 20
minutes, because that motor overheating may
cause internal damage; and the air pump shall
be fully cooled for 30 minutes after continuously
working up to 20 minutes.
VII. Precautions
*
*
*
*
*
*
*
*
*
*
Notice: The factory set pressure value of the air pump is 10PSI
(10PSI=0.689BAR), and at the time of the secondary use, the set
pressure value for the last time use will be displayed by default.
Notice: After powered on, if there is no operation within 2 minutes, the
air pump will enter standby mode, and the machine can be initiated
by pressing the power switch button
VI. Deflation operation
Remove the hose from the inflation inlet, Connect the end with
flexible conduit adaptor （11）of the hose with the air pump
deflation outlet (2), and twist clockwise totighten it, as Figure 3,and
the other end shall still be tothe airbag.
Press the button of the power switchof air pump, and start the
deflation until all the gas is discharged, then the power can be
turned off to stop the deflation.
.
HT-782 DC12V
（Figure 3）
*

STARPUMP 8 /9
VI. MISE EN GARDE
La source de courant doit délivrer une tension de 12V
continu ( Figure 3).
Ne pas empêcher l’air d’entrer par le bas de la pompe
et assurez vous que celle-ci n’est jamais obstruée.
Appliquez les dispositions de votre région concernant
le recyclage et le tri des déchets, ne jetez pas cette
pompe dans la nature.
Si le tuyau d’air est endommagé, n’utilisez pas cette pompe et procédez au
remplacement du tuyau.
Ne tirez pas sur le tuyau lors du gonage, la pression présente est élevée et
peut blesser physiquement.
Ne faites pas fonctionner cette pompe pendant plus de 20 minutes car celle
ci peut surchauer et endommager les composants internes.
Attendre 30 minutes pour être certain que la pompe à complètement refroidi
si celle-ci a fonctionné durant 20 minutes.
N’utiliser en aucun cas cette pompe de gonage si un ou plusieurs compo-
sant est endommagé ou manquant. Dans ce cas, contactez votre revendeur
pour eectuer sa réparation.
Ce produit ne doit pas être exposé à la pluie ou être immergé dans l’eau.
An de prévenir tout risque, a sortie d’air de la pompe ne doit pas etre tour-
née vers un visage ou un corps.
Rester près de la pompe de gonage pendant son fonctionnement
ATTENTION ! Pour un fonctionnement optimal, il est conseillé de laisser le
moteur de votre voiture tourner pendant l’utilisation du produit.
VI. MODE DÉGONFLAGE
• Dévissez le tuyau de gonage et connectez le à l’entrée d’air de la
pompe, puis le visser.
• Raccordez l’autre extrémité du tuyau à l’élément que vous souhaitez
dégoner.
• Appuyez sur le bouton marche de la pompe, et commencez le dégon-
age jusqu’à ce que l’élément soit complètement dégoné. Appuyez sur
le bouton On/o󰀨 pour arrêter le dégonage.
14
HT-785
I、Product Introduction
Thank you for purchasing this product. HT-785 is a DC electric air
pump that can inflate inflatable tent, SUP, etc. It has an intelligent
pressure system, such as if you set up the pressue, pump will
automatically stop inflating when pump pressure reaches the preset.
II、List of Accessories
III、List of Accessories
Please make sure that the following accessories are in the box
before using it, if any missing, please contact with the local supplier.
VI. Precautions
ELECTRIC AIR PUMP
Air pump Hose Instruction Book
23
1
4
5
Figure 3
When the pressure reaches the set value, the air pump will stop
working automatically.
After completing the inflation, pull out the DC plug from the 12V
DC socket.
After pulling out the DC plug, please take down the hose from the air
pump and air bag, and store it.
The applied power source must be the 12V DC power source
(as Figure 3).
Don't block the air inlet at the bottom of the air
pump, and guarantee air inlet to be always
unblocked.
Observe the local waste treatment provisions, and
it is not allowed to throw the air pump away randomly.
Don't use this product when the hose is damaged, and please change the
hose immediately.
Don't pull out the hose when inflating, because that the high pressure may
hurt the physical body.
Don't make the air pump work for more than 20minutes, because that motor
overheating may cause internal damage; and the air pump shall be fully
cooled for 30 minutes after continuously working up to 20 minutes.
Please don't use this air pump if any part is damaged, and please contact
with the professional person to repair it.
This product shall not be exposed to the rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward to face or body.
Please don't not leave while inflating.
Attention! For best results and to prevent any damage, please start
the car when using the product
5
Please don't use this air pump if any part is damaged, and please contact
with the professional personnel to repair it.
This product shall not be exposed tothe rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward toface or body.
Please don't not leave while inflating.
Please start the car when using the product, in case of unnecessary
damage.
VIII. Fault Handling
Fault Inspection Solution
The air pump
cannot be
started
normally.
1. The power source is
not plugged properly.
2. The fuse in DC plug
(7) is burnt out.
3. Overheating or
overload causes motor
stop.
1. Check whether the
hose is blocked or
cracked.
2. The joint between
the hose and air pump
or air bag is not
installed properly.
1. Make sure that the power wire is
plugged in the 12V DC socket.
2. Change the fuse.
3. Cool the motor and restart it.
4. If the problem cannot be solved,
please contact local service agents or
similar authorized personnel tochange
the product.
1. Change the hose or make it
unblocked, and check whether the hose
is cracked.
2. Reinstall the hose.
3. If the problem cannot be solved,
please contact local service agents or
similar authorized personnel tochange
the product.
Slow or
abnormal
inflation or
deflation.
IX. Maintenance and Storage
After using, or if you want to move, maintain or adjust the product,
please first pull out the DC plug from the socket.
when it is idle, it shall be properly stored after being fully cooled.
It shall not be exposed tothe rain or immersed in water.
Please store it in the dry and ventilated place.
X. Suggestions
The warranty period of this product is one year, and it is suggested to
use the original accessories. For any fault not caused by using the
original accessories, it shall be out of the warranty scope.
*
*
*
*
*
*
*
HT-782 DC12V
4
（Figure 4）
The applied power source must be the 12V DC power source (as Figure 4).
Do not block the inflation inlet (1) and Deflation outlet (2), and ensure that the
inflation inlet (1) and Deflation outlet (2) shall remain smooth at all times.
Observe the local wastetreatment provisions, and it is not allowed tothrow
the air pump away randomly.
Don't use this product when the hose is damaged, and please change the
hose immediately.
Don't pull out the hose when inflating, because that
the high pressure may hurt the physical body.
Don't make the air pump work for more than 20
minutes, because that motor overheating may
cause internal damage; and the air pump shall
be fully cooled for 30 minutes after continuously
working up to 20 minutes.
VII. Precautions
*
*
*
*
*
*
*
*
*
*
Notice: The factory set pressure value of the air pump is 10PSI
(10PSI=0.689BAR), and at the time of the secondary use, the set
pressure value for the last time use will be displayed by default.
Notice: After powered on, if there is no operation within 2 minutes, the
air pump will enter standby mode, and the machine can be initiated
by pressing the power switch button
VI. Deflation operation
Remove the hose from the inflation inlet, Connect the end with
flexible conduit adaptor （11）of the hose with the air pump
deflation outlet (2), and twist clockwise totighten it, as Figure 3,and
the other end shall still be tothe airbag.
Press the button of the power switchof air pump, and start the
deflation until all the gas is discharged, then the power can be
turned off to stop the deflation.
.
HT-782 DC12V
（Figure 3）
*

/10 STARPUMP 8
VII. FAULT HANDLING / PANNES ET ANOMALIES
Fault Inspection Solution
The air
pump
cannot be
started
normally.
La pompe
ne démarre
pas.
1. The power source
is not plugged
properly.
L’alimentation
n’est pas branchée
correctement.
2. The fuse in DC
plug is burnt out.
Le fusible est
défectueux
3. Overheating or
overload causes
motor stop.
Le moteur a sur-
chaué.
1. Make sure that the power wire
is plugged in the 12V DC socket.
Vérier que la pompe est bran-
chée sur une alimentation 12V
2. Change the fuse.
Changer le fusible
3. Cool the motor and restart it.
Laisser le moteur refroidir puis
réessayer.
4. If the problem cannot be sol-
ved, please contact with the ma-
nufacturer or its service agent or
the similar authorized personnel.
Si le problème persiste, contac-
tez notre revendeur.
Slow or
abnormal
ination.
Fonction-
nement
lent ou
anormal
1. Check whether
the hose is blocked
or cracked.
Vériez si le tuyau
est bloqué ou
ssuré.
2. The joint between
the hose and air
pump or air bag
is not installed
properly.
Le joint entre le
tuyau et la pompe
à air n’est pas ins-
tallé correctement.
1. Change the hose or make it
unblocked, and check whether
the hose is cracked.
Changer le tuyau ou le déblo-
quer, et vérier si il est ssuré.
2. Reinstall the hose.
Réinstaller le tuyau correcte-
ment.
3. If the problem cannot be
solved, please contact with the
manufacturer or its service agent
or the similar authorized person.
Si le problème persiste, contac-
tez notre revendeur.

STARPUMP 8 /11
VII. MAINTENANCE AND STORAGE / ENTRETIEN ET
STOCKAGE
After using, or if you want to move, maintain or adjust the product,please
rst pull out the DC plug from the socket.
• When it is idle, it shall be properly stored after being fully cooled.
• It shall not be exposed to the rain or immersed in water.
• Please store it in the dry and ventilated place.
• Après l’utilisation, ou si vous souhaitez déplacer, entretenir ou régler le
produit, débranchez d’abord la che CC de la prise.
• Ce produit doit avoir complètement refroidi avant d’être correctement
stocké.
• Il ne doit pas être exposé à la pluie ou immergé dans l’eau.
• Veuillez le conserver dans un endroit sec et ventilé.
IX. WARRANTY / GARANTIE
The warranty period of this product is one year, and it is suggested to use
the original accessories. For any fault not caused by using the original
accessories, it shall be out of the warranty scope.
La garantie de ce produit est d’un an, hors réglementation spécique
locale.
Pour tout défaut non causé par l’utilisation d’accessoires d’origine, il sera
hors de portée de la garantie.

/12 STARPUMP 8
PUMP
HT-782 Operation Instructions
Intelligent DC Electric Pump
Please read the operation instructions carefully before using this product.
Please operate in the correct way based on complete understanding.
Manufacturer:
Dongguan Huatao Metal and Plastic Products Co., Ltd.
Manufacturer's address:
Yanhe East Road, Xiabian Avenue, Chang'an Town,
Dongguan City, Guangdong Province, China
SUP ELECTRIC AIR PUMPSUP ELECTRIC AIR PUMP
960 avenue Olivier Perroy, 13790 ROUSSET - FRANCE
www.poolstar.fr