Portable Bar Company FOLD+ROLL BACK BAR User manual

FOLD+ROLL BACK BAR SETUP GUIDE

Note: This setup requires 2 or more persons.
2BEFORE YOU BEGIN THE INSTALLATION
• Read all the instructions before installing.
• Remove all packing materials before you start.
• This installation requires basic mechanical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under
the warranty.
• Keep this instruction manual.

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Main Cabinet
QTY: 1
Upper Frame
QTY: 1
Note: Parts are not to scale.
3
PART LIST
Ice bin
QTY: 2
Lock Pin
QTY: 8
Large Thumbscrews
QTY: 4
Acrylic Panel
QTY: 4
Front Acrylic
Side Acrylic
x2
Cutting Board
QTY: 3
Cover
QTY: 3
See page 11.
Upper Acrylic
(Pre-Installed on Main Cabinet)
Short Thumbscrews
QTY: 3

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
PART LIST
LED Controller
QTY: 1
Y
L
P
P
U
S
R
E
W
O
P
Power Adapter
QTY: 1
Battery
QTY: 1
LED Kit - Upper Shelves(if Purchased)
4
LED Kit - Main Cabinet(if Purchased)
LED Controller
QTY: 1
Y
L
P
P
U
S
R
E
W
O
P
Power Adapter
QTY: 1
Battery
QTY: 1
LED Strips
QTY: 2
LED Strip
QTY: 1
(With Velcro tape) (With Velcro tape)
(Pre-installed on Upper Frame) (Pre-installed on Main Cabinet)

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 1: Uninstall the hex screws and security tab at the top
of the upper frame.
STEP 2: Pull the acrylic panel out.
STEP 3: Remove protective film from the acrylic panel.
Figure 3
STEP 5: Using two people, lift upper frame and place onto main cabinet.
STEP 4: Follow steps 1 and 2 in reverse order to set panel.
Figure 1
Figure 2
Figure 4
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
Note: If laminate panel was ordered, skip to Step 5.
5

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 7: Install thumbscrews on both sides of the frame.
Figure 6
Figure 7. Full Assembly
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
STEP 6: Align the back part of the frame with the back edge of
the working surface, as shown below:
Figure 5
6
Note: Do not overtighten thumbscrews.

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
Folding the Fold+Roll Back Bar
STEP 1: Uninstall thumbscrews on both sides of the upper frame.
Figure 8
STEP 2: Take the Upper Frame assembly out and place it
temporarily on a flat and secure surface using
two people.
Figure 9
STEP 3: Fully open both doors.
Figure 10
STEP 4: Pull down the spring latch to release the door. Slightly
tilt and pull out the door. Do this step with both doors.
Figure 11
Figure 12
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS 7
Note: Disconnect controllers and batteries before
breaking down the bar.

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 5: Pull spring latches to release the working surface. Hold
the working surface while moving it to avoid damage.
STEP 6: Remove the 4 pins located on side frames,
as shown below.
Figure 13
Figure 14
Figure 15
STEP 7: Swing side frames while slightly lifting them.
Figure 16
STEP 8: Unscrew the far back thumbscrew. While you do so,
hold the support bar, once the thumbscrew is fully
out, the support bar will fall if not supported.
Figure 17
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
8
Note: Replace lock pins after swinging side frames.

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 9: Move up the base of the frame, hold it in place while
screwing the thumbscrews back onto the base.
As shown below;
STEP 10: Place upper assembly on the bar’s base, as shown;
Figure 18
Figure 19
Figure 21. Full Folded Assembly
Figure 20
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
STEP 11: Place doors between upper frame and folded base, then
place ice bins onto shelves of upper frame for storage.
Figure 21
Figure 22
9

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 1: Unscrew thumbscrew of center cutting board.
Ice bins installation
STEP 2: Take the center cutting board out.
STEP 3: Place ice bins.
Acrylic panels swapping
STEP 1: Fold down the bar. Follow Steps 1-7 on Page 6.
STEP 2: Remove all the screws located at the sides, and
uninstall the secuirty tab, as shown below.
STEP 3: Pull out acrylic panel.
Figure 25
Figure 26
Figure 22
Figure 23
Figure 24
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
10

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 4: Remove screws and security tab, as in the last step, this time for the back acrylic panel. Once the tab is fully removed,
pull out acrylic panel. Handle acrylic panel with care, it can scratch when in contact with hard surfaces.
Figure 27
Figure 28
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS 11

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
STEP 1: Place battery inside the cabinet, as shown below:
Cabinet LED Kit Installation
STEP 2: Using the included velcro tape, place the LED
Controller as shown below;
Figure 29
Figure 30
STEP 3: Connect the battery to the controller using the power out
battery port to the DC IN controller .
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS
(If purchased)
12
Upper Frame LED Kit Installation (If purchased)
STEP 1: Place battery underneath the bottom shelf on the
upper frame, inside casing as shown below:
Figure 31
STEP 3: Connect the battery to the controller using the power
out battery port to the DC IN controller .
STEP 2: Using the included velcro tape, place the LED
Controller as shown below;
Figure 32

PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED WITHIN THIS DOCUMENT IS THE SOLE PROPERTY OF THE PORTABLE BAR COMPANY
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF THE PORTABLE BAR COMPANY IS PROHIBITED.
FOLD+ROLL BACK BAR ASSEMBLY SETUP STEPS 13
Covers (3)
Upper and Lower covers for Upper Frame and Cabinet:
Cover for Folded position
1
2
3
1
2

Contact us
Tel # [phone]
Fax # [phone]
E-mail: [e-mail]
Visit us at
www.theportablebarcompany.com
FOLD+ROLL BACK BAR SETUP GUIDE - 06/2019