Check Digits
The following selections allow you to specify whether the check digit
should be transmitted at the end of the scanned UPC-A or UPC-E
data or not.
CodeGate/Manual Activation
Use the following programming codes to control CodeGate button/
trigger functions. Any time CodeGate is Active, you must push the
CodeGate button (on the top of the scanner)or press the trigger to
read a bar code. Whenever CodeGate is Inactive, the CodeGate
button/trigger does not need to be pressed. Bar codes are
automatically read when they are in the scanner’s field of view.
Host Configurations
Scan one of the following codes, then scan the Recall Defaults
code, to program the scanner for one of the following configurations.
Miscellaneous
Minimum Symbol Length specifies the minimum number of
characters allowable for non-UPC/EAN bar codes. Scan the Enter/
Exit Programming bar code to begin. Scan Minimum Symbol
Length, then scan the minumum number of characters allowed using
code byte bar codes, below. To save, scan the Enter/Exit
Programming bar code again.
ASCII Conversion Chart
Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char
000 NUL 26 1A SUB 52 34 478 4E N104 68 h
101 SOH 27 1B ESC 53 35 579 4F O105 69 i
202 STX 28 1C FS 54 36 680 50 P106 6A j
303 ETX 29 1D GS 55 37 781 51 Q107 6B k
404 EOT 30 1E RS 56 38 882 52 R108 6C l
505 ENQ 31 1F US 57 39 983 53 S109 6D m
606 ACK 32 20 58 3A :84 54 T110 6E n
707 BEL 33 21 !59 3B ;85 55 U111 6F o
808 BS 34 22 “60 3C <86 56 V112 70 p
909 HT 35 23 #61 3D =87 57 W113 71 q
10 0A LF 36 24 $62 3E >88 58 X114 72 r
11 0B VT 37 25 %63 3F ?89 59 Y115 73 s
12 0C FF 38 26 &64 40 @90 5A Z116 74 t
13 0D CR 39 27 ‘65 41 A91 5B [117 75 u
14 0E SO 40 28 (66 42 B92 5C \118 76 v
15 0F SI 41 29 )67 43 C93 5D ]119 77 w
16 10 DLE 42 2A *68 44 D94 5E ^120 78 x
17 11 DC1 43 2B +69 45 E95 5F _121 79 y
18 12 DC2 44 2C ,70 46 F96 60 ‘122 7A z
19 13 DC3 45 2D -71 47 G97 61 a123 7B {
20 14 DC4 46 2E .72 48 H98 62 b124 7C |
21 15 NAK 47 2F /73 49 l99 63 c125 7D }
22 16 SYN 48 30 074 4A J100 64 d126 7E ~
23 17 ETB 49 31 175 4B K101 65 e127 7F
24 18 CAN 50 32 276 4C L102 66 f
25 19 EM 51 33 377 4D M103 67 g
Technical Assistance
Contact information for technical support, product service, and repair can be
found at www.honeywellaidc.com.
Limited Warranty
Refer to www.honeywellaidc.com/warranty_information for your product’s
warranty information.
User Documentation
For localized versions of this document, and to download the Configuration
Guide or the Installation and User’s Guide, go to www.honeywellaidc.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other
information contained in this document without prior notice, and the reader should in all cases consult
HII to determine whether any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are reserved.
No part of this document may be photocopied, reproduced, or translated into another language without
the prior written consent of HII.
2010-2011 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
