Godex BP300 User manual

BP300/BP330 BARCODE PRINTER
USER MANUAL
User Manual
Version
Issue Date
P/N
: BP300 series
: Rev. A
: 2015.01.20
: 920-015711-00

Contents
BP300/BP330 USER MANUAL
CONTENTS
1
Barcode Printer
001
1.1
1.2
Box Content
Getting To Know Your Printer
001
002
2
Printer Setup
004
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Open The Printer Cover
Open The Printing Mechanism
Loading The Ribbon
Loading The Label Roll
Installing The Label Supply Hub
Connecting The Printer To The Host Computer
Installing The Driver
004
004
005
009
012
013
015
3
Operation Panel
018
3.1
3.2
3.3
LED Operation Panel
Error Alerts
Label Calibration and Self Test Page
018
019
020
4 NetSetting For Ethernet 021
4.1
4.2
Installing The NetSetting Software
The Interface of NetSetting
021
022
5 Maintenance and Adjustment 029
5.1
5.2
5.3
5.4
Cleaning The Print Head
Adjusting The Print Head Pressure
Adjusting The Print Line
Troubleshooting
029
030
031
032
Appendix
Product Specifications
Interface

BP300 SERIES

BP300 Barcode Printer

1Barcode Printer
1.1 Box Content
Please check that all of the following items are included with your printer
1
USB Cable

CD
Including QLabel software
and BP300 user manual.

Ribbon Module
Empty Ribbon Core
Ribbon
Power Adapter
Power Cord
AC Adapter

Label Supply Module
Label Supply Hub
Label Guide Plates(Set of 2)
Label Stock

BP300 Quick Guide

BP300/BP330

2
Front View

1Barcode Printer
1.2 Getting To Know Your Printer
002
Device Overview
Rear View

TOP COVER
COVER OPEN BUTTONS
Release buttons for opening the printer cover
LED INDICATOR
FEED BUTTON
LED OPERATION PANEL
ETHERNET PORT
POWER SLOT
POWER SWITCH
- ON
- OFF
FAN-FOLD LABEL INSERT
Feed slot for continuous labels
USB PORT
SERIAL PORT

3
1Barcode Printer
Open The Printer Cover
RELEASE CATCH(Left)
SCREW(Left)
Screw for adjusting the print head pressure
LABEL SUPPLY MODULE
- LABEL SUPPLY HUB
- LABEL GUIDE PLATES(Set of 2)
RELEASE CATCH(Right)
SCREW(Right)
Screw for adjusting the print head pressure
RIBBON REWIND WHEEL
HOLDER OF RIBBON REWIND CORE
003
Open The Printing Mechanism
PLATEN
LABEL GUIDE(Right)
LABEL SENSOR
LABEL GUIDE(Left)
ADJUSTMENT SCREW
Screw for adjusting
the printer line
PRINTING MECHANISM
RIBBON SUPPLY
WHEEL
HOLDER OF
RIBBON SUPPLY CORE
PRINT HEAD

4
2Printer Setup
2.1 Open The Printer Cover
Pressing The Cover Open Buttons
Place the printer on a flat surface. Open the printer cover by pressing the release buttons on both sides of the printer
housing and lift the cover.
004
Lift the printer cover backward
COVER OPEN BUTTONS
Release buttons for opening the printer cover.
Pressing the button
Pressing the button
Lift the printing mechanism
Pressing
Pressing
RELEASE CATCHES
2.2 Open The Printing Mechanism
Pressing The Release Catches
Release and lift the printing mechanism.

2Printer Setup
2.3 Loading The Ribbon
5
A New Ribbon Module Installation
NEW RIBBON EMPTY RIBBON CORE
Wind the ribbon around the core
1. Attach the ribbon to the empty ribbon core with the adhesive strip at the end of the ribbon.
2. Wind the ribbon around the empty ribbon core for 2 to 3 circles.
Stick on empty ribbon core
Notch on left side
A NEW RIBBON MODULE
RIBBON SUPPLY
RIBBON REWIND
3. A ribbon module is assembled as below.

6
2Printer Setup
006
2. Then place the left-hand side of the ribbon.
Load The Ribbon On The Printer
For Ribbon Supply Module
1. Place the right-hand side of ribbon first.
RIBBON SUPPLY MODULE
Right side
Push the ribbon to tighten
the spring of the holder
HOLDER
SPRING OF HOLDER
Align the ribbon core
to the holder
Left side
NOTCH OF RIBBON CORE
SPOKE
GEAR
Rotate the gear for alignment
if necessary
Align the notch of the ribbon core to the spoke

7
2Printer Setup
007
3. Close the printing mechanism to complete the ribbon supply module loading.
Load The Ribbon On The Printer
For Ribbon Rewind Module
RIBBON REWIND MODULE
1. Place the right-hand side of empty ribbon core first.
Right side
Align the empty ribbon core
to the holder
HOLDER
Push the empty ribbon core
to tighten the spring of the holder
SPRING OF HOLDER
Close the printing mechanism