pottery barn kids BELDEN BED User manual

1
pottery barn kids
BELDEN
BED
PRE
-
ASSEMBLY:

Remove all parts and hardware from the box and lay out on a clean carpeted or scratch
-
free work surface (The shipping
box provides an ideal work surface). This will avoid damaging any parts during assembly. Do no
t dispose of any contents
until assembly is completed to avoid accidentally discarding small parts or hardware.

Two people recommended for ease of assembly.

Usethe parts and hardware lists to identify and separate each of the pieces included prior tostar
ting assembly.

The illustrations provided allowfor easier assembly when used in conjunction with the assembly instructions.

Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts t
o
misa
lign during assembly.

If using power tools to aid in assembly please use caution. Power tools can damage hardware or split wood.
PARTS INCLUD
ED:
A
–
Front panel (1)
B
–
Back panel (1)
C
–
Left side panel (1
)
D
–
Right side p
anel (1)
E
-
Bottom
frame
with
drawers (
1)
F
-
Slat
rolls
(1)
G
–
Drawer
fill
-
in panel (1)
TOOLS REQUIRED:
Phillips head screwdriver (not included)
H
–
Allen Key (included)
HARDWARE INCLUDED:
I
–
A
llen bolt 1/4
”
x32x15mm (
7
)
J
–
Large
Phillips
head screw 8x30mm (28)
K
–
Small
Phillips
head screw
8x1
7
mm (
12
)
L
–
Mending plate 70x40mm (2)

2
M
–
Leveller
120x37x29mm (1)
N
-
Wooden
dowel 8x25mm (2)
ASSEMBLY:
1. Pull 2 Drawer out from the Bottom frame (E) as shown.
2.
Attach the leveler (M) to the Bottom frame (E
) using 4pcs
Small
Phillips
head screw
8x17
mm
(K)
,
ti
ghten with
Phillips head screwdriver (not included).

3
3. Lay down the Front panel (A) and
attach 2pcs
Wooden
dowel 8x25mm (N) to the Bottom panel (E)
,
make sure
the pre
-
drilled holes align. Attach the Bottom frame (
E
) to the Front panel (
A)
using 3pcs
Allen bolt 1/4
”
x32x15mm
(
I) and Allen key (H)
4
.
Attach the
Left
Side panel (
C)
and Right Side panel (D)
up to slots on the
Front
Panel
(A) and
Back panel
(B) by
inserting the hooked ends into the corresponding
slots,
as shown below. Ensure that the connections are secure.

4
5.
Fix the
Bottom frame (E
) to
Left
Side panel (
C)
and Right Side
panel (D)
using 4pcs
Allen bolt 1/4
”
x32x15mm
(I
),
tighten with Allen key (H
).
Then
tighten the leveler as shown.
6. Put the drawer boxes back to the Bottom frame (E)
by aligning the wooden runners
making
sure the drawer
fit
s
properly.

5
7
. If only
one
drawer is needed
,
replace that open drawer front using the drawer
Fill
-
in panel (G
),
make sure the
bead board align
s properly
for both the Front panel (A) and Drawer Fill
-
in
panel
(G)
,
then fix 2pcs Mending plate
70x40mm
(
L
) through the pre
-
dr
illed holes by using 8pcs
Small Phillips head screw
8x17
mm
(
K
) and Phillips head
screwdriver (not
included).
8.
Lay the slat roll (E) in between the Front
panel
(A)
and the Back
panel
(B) using 28 pc
Large
Phillips
head screw
8x30mm
(
J
), affix the Slat Roll (E) to the bed frame and loosely tighten with the Phillips Head Screwdriver.
Tighten
all bolts and screws to make sure all are tight and bed structure is rigid. It is recommended all screws be checked
from time to time for safety as the hardware may loosen over time.
T
hank you for your purchase
.
stores | cata
log |
www.potterybarnkids.com